Yes you can have upto 4 SREs running SRE-V in 3945e / 3945 chassis.



Thanks



Anurag Gurtu, CISSP

Hi anurag,

Thanks for your reply.

can i use the same gateway and network for another sre-910.

Regards
kshitij

Hi ,

i am not able to install sre-v on another sre-910 blade.

sre status is

Router#service-module sm 2/0 status
Service Module is Cisco SM2/0
Service Module supports session via TTY line 130
Service Module is failed
Service Module heartbeat-reset is enabled
Service Module is in fail open
Service Module status is not available
No install/uninstall in progress

Local Partition Info
=====================
Please reset module to retrieve
partition information if needed

can not ping TFTP from bootloader menu.

router configuration is

interface GigabitEthernet0/0
no ip address
shutdown
duplex auto
speed auto
!
interface GigabitEthernet0/1
ip address 10.65.157.175 255.255.254.0
duplex auto
speed auto
!
interface GigabitEthernet0/2
ip address 192.168.1.1 255.255.255.0
duplex auto
speed auto
!
interface GigabitEthernet0/3
no ip address
shutdown
duplex auto
speed auto
!
interface SM1/0
ip unnumbered GigabitEthernet0/1
service-module ip address 10.65.157.176 255.255.254.0
!Application: VMware ESXi 5.0.0 build-474610 running on SRE
service-module ip default-gateway 10.65.157.175
!
interface SM1/1
description Internal switch interface connected to Service Module
no ip address
!
interface SM2/0
ip unnumbered GigabitEthernet0/1
service-module fail-open
service-module ip address 10.65.157.180 255.255.254.0
service-module ip default-gateway 10.65.157.175
!
interface SM2/1
description Internal switch interface connected to Service Module
no ip address
!
interface Vlan1
no ip address
shutdown
!
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
ip route 0.0.0.0 0.0.0.0 10.65.156.1
ip route 10.65.157.176 255.255.255.255 SM1/0
ip route 10.65.157.177 255.255.255.255 SM1/0
ip route 10.65.157.180 255.255.255.255 SM2/0
!
!
!

Regards
Kshitij

Hi,

when i try to seession on sm 2/0 it shows

Router#service-module sm 2/0 session
Trying 10.65.157.175, 2130 ...
% Connection refused by remote host

Regards
Kshitij

Router#service-module sm 2/0 session clear ?
<cr>

Router#service-module sm 2/0 session clear


Router#service-module sm 2/0 session
Trying 10.65.157.175, 2130 ... Open


Time-out from RBIP response wait loop


Time-out from RBIP response wait loop


Time-out from RBIP response wait loop

Can you reset the sm module the CLI “service-module sm 2/0 reset” command and then enable the debug on ios using the command “debug scp install all” and give us the output of the debug commands.



Thanks,

Radhika



From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
Sent: Tuesday, March 27, 2012 10:20 AM
To: cdicuser@developer.cisco.com
Subject: New Message from Kshitij Purwar in Service Ready Engine Virtualization - SRE-V Technical Questions: RE: can i add one more sre-910 on cisco 3945



Kshitij Purwar has created a new message in the forum "SRE-V Technical Questions":

--------------------------------------------------------------
Hi,

SRE installation step 1 failed

Abort initiated due to RBIP timeout


Time-out from RBIP response wait loop


Time-out from RBIP response wait loop
Valid link not established
Valid link not established
Loading disk:/bzImage ... done.
Unable to load image
Error: Selected disk does not exist (21)
ÿnable to boot image



Initializing memory #1. Please wait...




Initializing memory #2. Please wait...


This may take a minute....


Serial ATA Port 0 : ST9500620NS
Serial ATA Port 1 : ST9500620NS
DDR Memory 4096 MB detected
Intel(R) Core(TM)2 Duo CPU L9400 @ 1.86GHz
BIOS SM 3.52.8, BIOS Build date: 02/08/2011

Intel(R) Core(TM)2 Duo CPU L9400 @ 1.86GHz
BIOS SM 3.52.8, BIOS Build date: 02/08/2011
System now booting...


Please wait...

Please press P to select Primary Boot Loader ...
or S to select Secondary Boot Loader ...
or wait to boot from default configuration ...

.......................................................................................................
SRE module get located and run....

Now booting from secondary boot loader....


Authenticating boot loader....


Secondary Boot Loader authenticated - booting....

Valid link not established


Please enter '***' to change boot configuration:

Detect and Initialize network device
Valid link not established


Backup current platform configurations....

SRE step 1 - SM registration...
Finding (hd1,3)/296e03bc-3236-4a68-a178-688e56400a1e, failed
Local install not supported


Time-out from RBIP response wait loop


Time-out from RBIP response wait loop
--
To respond to this post, please click the following link:

<http://developer.cisco.com/web/srev/forums/-/message_boards/view_message/5360075>

or simply reply to this email.

Forgot to mention that after you enable the debugs please try install so we can see debug messages.



From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
Sent: Tuesday, March 27, 2012 10:24 AM
To: cdicuser@developer.cisco.com
Subject: New Message from Radhika Miriyala in Service Ready Engine Virtualization - SRE-V Technical Questions: RE: New Message from Kshitij Purwar in Service Ready Engine Virtualization



Radhika Miriyala has created a new message in the forum "SRE-V Technical Questions":
--------------------------------------------------------------
Can you reset the sm module the CLI “service-module sm 2/0 reset” command and then enable the debug on ios using the command “debug scp install all” and give us the output of the debug commands.



Thanks,

Radhika



From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
Sent: Tuesday, March 27, 2012 10:20 AM
To: cdicuser@developer.cisco.com
Subject: New Message from Kshitij Purwar in Service Ready Engine Virtualization - SRE-V Technical Questions: RE: can i add one more sre-910 on cisco 3945



Kshitij Purwar has created a new message in the forum "SRE-V Technical Questions":

--------------------------------------------------------------
Hi,

SRE installation step 1 failed

Abort initiated due to RBIP timeout


Time-out from RBIP response wait loop


Time-out from RBIP response wait loop
Valid link not established
Valid link not established
Loading disk:/bzImage ... done.
Unable to load image
Error: Selected disk does not exist (21)
ÿnable to boot image



Initializing memory #1. Please wait...




Initializing memory #2. Please wait...


This may take a minute....


Serial ATA Port 0 : ST9500620NS
Serial ATA Port 1 : ST9500620NS
DDR Memory 4096 MB detected
Intel(R) Core(TM)2 Duo CPU L9400 @ 1.86GHz
BIOS SM 3.52.8, BIOS Build date: 02/08/2011

Intel(R) Core(TM)2 Duo CPU L9400 @ 1.86GHz
BIOS SM 3.52.8, BIOS Build date: 02/08/2011
System now booting...


Please wait...

Please press P to select Primary Boot Loader ...
or S to select Secondary Boot Loader ...
or wait to boot from default configuration ...

.......................................................................................................
SRE module get located and run....

Now booting from secondary boot loader....


Authenticating boot loader....


Secondary Boot Loader authenticated - booting....

Valid link not established


Please enter '***' to change boot configuration:

Detect and Initialize network device
Valid link not established


Backup current platform configurations....

SRE step 1 - SM registration...
Finding (hd1,3)/296e03bc-3236-4a68-a178-688e56400a1e, failed
Local install not supported


Time-out from RBIP response wait loop


Time-out from RBIP response wait loop
--
To respond to this post, please click the following link:

<http://developer.cisco.com/web/srev/forums/-/message_boards/view_message/5360075>

or simply reply to this email.
--
To respond to this post, please click the following link:
<http://developer.cisco.com/web/srev/forums/-/message_boards/view_message/5360085>
or simply reply to this email.

Hi,

Router#$ule sm 2/0 install url ftp://192.168.1.2/sre-v-k9-r.SPA.smv.2.0.1.pkg
Proceed with installation? : yes
Router#
[Resuming connection 1 to 10.65.157.175 ... ]




Initializing memory #1. Please wait...

Detect and Initialize network device
Valid link not established


Backup current platform configurations....

SRE step 1 - SM registration...
Finding (hd1,3)/296e03bc-3236-4a68-a178-688e56400a1e, failed
Local install not supported


Time-out from RBIP response wait loop


Time-out from RBIP response wait loop

Hi,

I plugged the blade when the router was on and working.

Regards
kshitij

no i didnt use this command.
can i run it now.

try for installation again but no luck


Router#$ule sm 2/0 install url ftp://192.168.1.2/sre-v-k9-r.SPA.smv.2.0.1.pkg
Proceed with installation? : yes

no op return back to router cli.

Hi,

right now i am not near by router,i can try it tomorrow.

thanks for all your valuable info for my troubleshooting.if i will hv any issue,i will let you know.

Regards
kshitij