Hi, i have one 3945e router with default ios image 15.1 M4,when i connect one sre910,i can see int sm 1/0 on router console,but when i upgrade the router iso imge to 15.1 T2,then i can not see sre910 on router console. run the below comand hw-module oir-stop hw-module oir-start but no luck,then the slot from 1 to 2 but still no luck. can anybody please help me here. Thanks kshitij

Hi Brett,
Thanks for reply.
but we want to test cme version 8.0 which is supported on this iso image only.
is there any workaround to fix this issue.
Thanks
kshitij

Hi Kshitij,
I found a link to a webpage that describes the CME releases and its corresponding IOS versions.  It has a footnote that says to get the latest release of the IOS rebuild, so you should be able to use a later IOS image.  Please also note that CME is currently on release 9.1, so I'm sure they'd recommend using a later release of CME as well.
http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/requirements/guide/33matrix.htm
Thanks,
Brett

Hi Brett,
Sorry for my late reply.Please find the attached doc as you required.
we want to install cuc on sre blade 910/900 for testing,and want to test it with different falouu of cme-srst image which are supported on router 3900/2900.
I updated the router iso image to 15.1(1) T5,but still it in not working.
please let me know,is there any way we can test sre blade with cuc on it and cme-srst 8.0 on router.
 
Thanks
kshitij

Hi Kshitij,
Thanks for the data.  I can see that the SRE service module is not being recognized by the earlier IOS versions that you would like to use.  Our documentation specifies that you need to use IOS release 15.1(4)M at minimum.  I see from the CME chart that I provided to you that this IOS release contains CME 8.6 .   I don't have specifications for the T train; however I checked the SRE configuration guide at http://www.cisco.com/go/sre , and it appears that you could use IOS version 15.1(3)T; however this release contains CME version 8.5 .  In either case I don't think CME 8.0 is a viable candidate for use on the router with the SRE service module because a later IOS version is required for the SRE.
Thanks,
Brett

Try

Sh ver or sh inv

Thanks

Anurag Gurtu

On Nov 22, 2012, at 10:47 AM, "Cisco Developer Community Forums" <cdicuser@developer.cisco.com<mailto:cdicuser@developer.cisco.com>> wrote:

Kshitij Purwar has created a new message in the forum "SRE-V Technical Questions": -------------------------------------------------------------- Hi Brett,
thanks your valuable inputs provided here.
is there any command to find out the router chassis is 3945 or 3945e.
as i know cisco 3945 has spe150 and 3945e has spe 250.
Thanks
kshitij
--
To respond to this post, please click the following link: <http://developer.cisco.com/web/srev/forums/-/message_boards/view_message/8755425> http://developer.cisco.com/web/srev/forums/-/message_boards/view_message/8755425 or simply reply to this email.

Hi Brett, i used 15.1 (3) T,but still i can not install SRE-V on 910/900. getting below
error-

Warning: Router's ROMMON ne eds to be upgraded to suppport proper operation of module SM-SRE-900-K9 SM-SRE-9 10-K9 . Operation SM-SRE-900-K9 SM-SRE-910-K9  without upgrading ROMMON may caus e the module hard disk driver to become unstable.

Thanks kshitij

Hi Kshitij,
You should be able to get the router chassis and hardware via the command: 'show diag | inc FRU'.
It sounds like you need to upgrade the ROMMON software on the router, so that the SRE hardware is recognized.  You can download the ROMMON software from http://www.cisco.com/cisco/software/navigator.html?a=a&i=rpm .  You'll need to go through the selections to locate it such as what I've listed below. After downloading the IOS ROMMON software you can upgrade the router via command: "upgrade rom-monitor file ftp://<ip>/file"
1.  Click 'Cisco IOS and NX-OS software'
2. Click 'Cisco IOS'
3. Click '<a>Cisco IOS Software Release 15M&T'</a>
4. Click '<a>Cisco IOS 15.1M&T'</a>
5. Click 'Routers'
6. Click 'Branch Routers'
7. Click 'Cisco 3900 Series Integrated Routers'
8. Click 'Cisco 3945E Integrated Services Router'
9. For Software Type click 'IOS ROMMON Software'
 
Thanks,
Brett

Hi Kshitij,

Unfortunately I don't have a 3945e ISR in my lab; however an easy way to identify whether you have a 3945e or a 3945 ISR is by the number of GE Interfaces.  The 3945e has 4 while the 3945 has 3.  I've attached a link to a document that does a side-by-side comparison on page 2 of the different ISR routers including the 3945e/3945. 
www.cisco.com/en/US/prod/collateral/routers/ps10538/aag_c45_556315.pdf
Thanks,
Brett

Thanks Manuka and Brett for helping me here.
I got it I have 3945e.

I have upgraded the router rommon 15.1 (1r)T5 from 15.1 (1r) T4 which was default.
But still I am not able to install sre-v on sre 900,910.
Kindly see the attached logs.

Thanks
kshitij
From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com]
Sent: Tuesday, December 04, 2012 1:44 AM
To: cdicuser@developer.cisco.com
Subject: New Message from Manuka Jayakody in Service Ready Engine Virtualization - SRE-V Technical Questions: RE: find new intresting issue on SRe 3945 router

Manuka Jayakody has created a new message in the forum "SRE-V Technical Questions": -------------------------------------------------------------- Hi Kshitij,
PID "C3900-SPE250/K9" means that you have a 3945e router. 3925, 3945, 3925e, 3945e share the same chassis and that's why you see the "CISCO3945-CHASSIS" in the output.
if you have a 3945 you should see the PID as C3900-SPE150/K9.
3925 - C3900-SPE100/K9
3925e - C3900-SPE200/K9
thanks
Manuka
--
To respond to this post, please click the following link: http://developer.cisco.com/web/srev/community/-/message_boards/view_message/9043375 or simply reply to this email.

Attachments: