Developer Network

SRE-V Forums

« Back to SRE-V Technical Questions

Loading the SRE with ESXi

Combination View

Post New Thread

Showing 1 - 20 of 34 results.

First Previous Next Last

SCOTT PITTS Posts: 47 Join Date: 9/1/10 Recent Posts	Loading the SRE with ESXi Answer 4/19/11 6:32 PM Mark as an Answer Submit Reply with Quote Quick Reply I have tried many things at this point to attempt to get the software loaded on the SRE. The two most recenct SRE's were apparently shipped with nothing on them and I believe the first one we got had the AXP image on it. The first one is loaded but these two SRE's do not seem to be co-operating. These 2 SREs will load the TFTP boot image but then have the following message. disk:bzImage ... done Loading Disk:/cmdlineextra ... done Verifying ... Verifying application key failed, ret=0 done Starting Kernel and then reboots over and over. the FTP/TFTP server is on a different subnet than the SRE. I have tried to use the Internal interface with the static route to the IP to utlize the same net as GIG0/0. I tried NATing it from a GIG0/0 address to a internal address that I put on the SM1/0. I tried using the config command on the SRE and using the external interface. This is on a Cisco 2911sec/k9 with an SRE900.
	Sign in to vote. Flag Please sign in to flag this as inappropriate. Top

Stefan de Kooter Posts: 6 Join Date: 10/15/08 Recent Posts	Automatisch antwoord: New Message from SCOTT PITTS in Service Ready Engine Answer 11/20/10 7:33 AM as a reply to SCOTT PITTS. Mark as an Answer Submit Reply with Quote Quick Reply ¿ Geachte dame/heer, Tot maandag 27 september ben ik niet aanwezig en heb ik geen toegang tot e-mail en voicemail. Een reactie op uw bericht kunt u na deze datum verwachten Wilt u een nieuw ticket aanmelden of een bestaand probleem escaleren, stuur uw bericht dan naar helpdesk@proxsys.nl. Met vriendelijke groet, Stefan de Kooter Projects PROXSYS* Spijksedijk 16H 4207 GN Gorinchem K.V.K. 11051004 T 0183 - 645 080 F 0183 - 645 081 I www.proxsys.nl<http://www.proxsys.nl/>
	Sign in to vote. Flag Please sign in to flag this as inappropriate. Top

Anurag Gurtu Posts: 62 Join Date: 4/2/08 Recent Posts	RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - S Answer 11/20/10 7:33 AM as a reply to SCOTT PITTS. Mark as an Answer Submit Reply with Quote Quick Reply Which application are you trying to install on SRE?
	Sign in to vote. Flag Please sign in to flag this as inappropriate. Top

Radhika Miriyala Posts: 174 Join Date: 8/12/10 Recent Posts	RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - S Answer 11/20/10 7:33 AM as a reply to SCOTT PITTS. Mark as an Answer Submit Reply with Quote Quick Reply Scott, A few questions. How are you installing the image? Are you using the SRE install CLI¿ Service-module sm x/0 install url ftp://<ip address>/<image directory> to install? Or are you using the old method of boot helper to install? Can you also provide the console log of the whole install process so we can take a look to see where exactly the system fails. Thanks, Radhika From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com] Sent: Wednesday, September 08, 2010 6:44 AM To: cdicuser@developer.cisco.com Subject: New Message from SCOTT PITTS in Service Ready Engine Virtualization - SRE-V Beta Testing: Loading the SRE with ESXi SCOTT PITTS has created a new message in the forum "SRE-V Beta Testing": -------------------------------------------------------------- I have tried many things at this point to attempt to get the software loaded on the SRE. The two most recenct SRE's were apparently shipped with nothing on them and I believe the first one we got had the AXP image on it. The first one is loaded but these two SRE's do not seem to be co-operating. These 2 SREs will load the TFTP boot image but then have the following message. disk:bzImage ... done Loading Disk:/cmdlineextra ... done Verifying ... Verifying application key failed, ret=0 done Starting Kernel and then reboots over and over. the FTP/TFTP server is on a different subnet than the SRE. I have tried to use the Internal interface with the static route to the IP to utlize the same net as GIG0/0. I tried NATing it from a GIG0/0 address to a internal address that I put on the SM1/0. I tried using the config command on the SRE and using the external interface. This is on a Cisco 2911sec/k9 with an SRE900. -- To respond to this post, please click the following link: <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2515364> or simply reply to this email.
	Sign in to vote. Flag Please sign in to flag this as inappropriate. Top

SCOTT PITTS Posts: 47 Join Date: 9/1/10 Recent Posts	RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - S Answer 11/20/10 7:33 AM as a reply to Radhika Miriyala. Mark as an Answer Submit Reply with Quote Quick Reply Here is the output from the attempted load of the SRE with the ESXi image followed by a show config. I hope this helps. Router#$l ftp://pittssc:cisco7500@10.10.97.51/sre-v-k9.smv.1.0.0.19.pkg Proceed with installation? : y Loading sre-v-k9.smv.1.0.0.19.pkg.install.sre ! [OK - 1757/4096 bytes] Service module installation ios_version 15.0(1)M2, ios_image c2900-universalk9-mz pkg_name sre-v-k9.smv.1.0.0.19.pkg key_file sre-v-k9.smv.1.0.0.19.key helper_file sre-v-installer.smv.1.0.0.19 Check target platform capabilities cpu 1865 Resource check completed successfully. Proceeding to Install.... Router# Sep 8 18:07:13.006: %SM_INSTALL-6-INST_RESET: SM1/0 is reset for software installation. [Resuming connection 1 to 192.168.75.5 ... ] Initializing memory. Please wait... Initializing memory. Please wait... 4,290,379,776 bytes of system memory tested OK Channel 0 Master : Hitachi HTE545050B9A300 Channel 1 Master : Hitachi HTE545050B9A300 DDR Memory 4096 MB detected Intel(R) Core(TM)2 Duo CPU L9400 @ 1.86GHz BIOS SM 2.4, BIOS Build date: 11/04/2009 Intel(R) Core(TM)2 Duo CPU L9400 @ 1.86GHz BIOS SM 2.4, BIOS Build date: 11/04/2009 System now booting... Please wait... Please press P to select Primary Boot Loader ... or S to select Secondary Boot Loader ... or wait to boot from default configuration ... ....................................................................................................... Now booting from primary boot loader.... Authenticating boot loader.... Primary Boot Loader Authenticated - booting.... Please enter '*' to change boot configuration: Detect and Initialze network device Backup current platform configurations.... SRE step 1 - SM registration... SRE step 2 - SM requests key file info... Sep 8 18:07:58.630: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request Sep 8 18:07:58.634: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request SRE step 3 - SM stores registration info... SRE configuration keeps the same. No flash update needed! SRE step 4 - SM downloads key-file... Writing keyfile to flash Size 919 writing complete. Updating flash with bootloader configuration. Please wait .................. done. SRE step 5 - SM requests installer info... Sep 8 18:08:05.486: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request SRE step 6 - SM stores installer info... Updating flash with bootloader configuration. Please wait .................. done. SRE step 7 - SM now downloads installer done. SRE step 8 - SM requests tcl header file info... Sep 8 18:08:21.194: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request SRE step 9 - SM now downloads the tcl header file TCL header file downloaded completely size: 698 SRE step 10 - SM requests tcl file info... Sep 8 18:08:26.674: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP File Request SRE step 11 - SM now downloads the tcl file TCL file downloaded completely size: 1757 SRE step 12 - SM now boots Installer Verifying ... Verifying application key failed, ret=0 done. Starting Kernel. þ Initializing memory. Please wait... Initializing memory. Please wait... 4,290,379,776 bytes of system memory tested OK Channel 0 Master : Hitachi HTE545050B9A300 Channel 1 Master : Hitachi HTE545050B9A300 DDR Memory 4096 MB detected Intel(R) Core(TM)2 Duo CPU L9400 @ 1.86GHz BIOS SM 2.4, BIOS Build date: 11/04/2009 Intel(R) Core(TM)2 Duo CPU L9400 @ 1.86GHz BIOS SM 2.4, BIOS Build date: 11/04/2009 System now booting... Please wait... Please press P to select Primary Boot Loader ... or S to select Secondary Boot Loader ... or wait to boot from default configuration ... ....................................................................................................... Now booting from primary boot loader.... Authenticating boot loader.... Primary Boot Loader Authenticated - booting.... Please enter '**' to change boot configuration: Detect and Initialze network device Backup current platform configurations.... SRE step 1 - SM registration... Verification error occurred, cancelling installation Updating flash with bootloader configuration. Please wait .................. done. Sep 8 18:09:17.630: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request Error message(code:0) Keyfile Verification Failed received on SM1/0 SRE Step 1 complete ending installation Sep 8 18:09:19.958: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Error Msg Req Sep 8 18:09:19.958: %SM_INSTALL-6-RBIP_ERROR: Error message(code:0) Keyfile Verification Failed received on SM1/0 ServicesEngine Bootloader Version : 2.1.27 ServicesEngine boot-loader> Initializing memory. Please wait... Initializing memory. Please wait... 4,290,379,776 bytes of system memory tested OK Channel 0 Master : Hitachi HTE545050B9A300 Channel 1 Master : Hitachi HTE545050B9A300 DDR Memory 4096 MB detected Intel(R) Core(TM)2 Duo CPU L9400 @ 1.86GHz BIOS SM 2.4, BIOS Build date: 11/04/2009 Intel(R) Core(TM)2 Duo CPU L9400 @ 1.86GHz BIOS SM 2.4, BIOS Build date: 11/04/2009 System now booting... Please wait... Please press P to select Primary Boot Loader ... or S to select Secondary Boot Loader ... or wait to boot from default configuration ... ....................................................................................................... Now booting from primary boot loader.... Authenticating boot loader.... Primary Boot Loader Authenticated - booting.... Please enter '**' to change boot configuration: Detect and Initialze network device Backup current platform configurations.... SRE step 1 - SM registration Abort successful on SM1/0 ... Response - no installation needed (len: 422) SRE Installation Not Needed Restoring orignial configuration... Updating flash with bootloader configuration. Please wait .................. done. Sep 8 18:10:35.630: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request Sep 8 18:10:35.630: %SM_INSTALL-6-INST_ABORT: SM1/0 SW installation aborted, reason:user command ServicesEngine Bootloader Version : 2.1.27 ServicesEngine boot-loader> Show Config Initializing memory. Please wait... Initializing memory. Please wait... 4,290,379,776 bytes of system memory tested OK Channel 0 Master : Hitachi HTE545050B9A300 Channel 1 Master : Hitachi HTE545050B9A300 DDR Memory 4096 MB detected Intel(R) Core(TM)2 Duo CPU L9400 @ 1.86GHz BIOS SM 2.4, BIOS Build date: 11/04/2009 Intel(R) Core(TM)2 Duo CPU L9400 @ 1.86GHz BIOS SM 2.4, BIOS Build date: 11/04/2009 System now booting... Please wait... Please press P to select Primary Boot Loader ... or S to select Secondary Boot Loader ... or wait to boot from default configuration ... ....................................................................................................... Now booting from primary boot loader.... Authenticating boot loader.... Primary Boot Loader Authenticated - booting.... Please enter '*' to change boot configuration: Detect and Initialze network device Backup current platform configurations.... SRE step 1 - SM registration Abort successful on SM1/0 ... Response - no installation needed (len: 422) SRE Installation Not Needed Restoring orignial configuration... Updating flash with bootloader configuration. Please wait .................. done. Sep 8 18:10:35.630: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request Sep 8 18:10:35.630: %SM_INSTALL-6-INST_ABORT: SM1/0 SW installation aborted, reason:user command ServicesEngine Bootloader Version : 2.1.27 ServicesEngine boot-loader> *********************************************SHOW CONFIG******************************************************* Router#show config Using 1941 out of 262136 bytes ! ! Last configuration change at 21:11:55 UTC Tue Sep 7 2010 ! version 15.0 service config service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Router ! boot-start-marker boot-end-marker ! ! no aaa new-model ! ! ! memory-size iomem 20 ! no ipv6 cef ip source-route ip cef ! ! ! ! ! multilink bundle-name authenticated ! ! ! ! license udi pid CISCO2911/K9 sn FTX1429A35B hw-module sm 1 ! ! ! vtp version 2 ! redundancy ! ! ! ! ! ! ! ! ! interface GigabitEthernet0/0 ip address dhcp ip nat outside ip virtual-reassembly duplex auto speed auto ! ! interface GigabitEthernet0/1 no ip address shutdown duplex auto speed auto ! ! interface GigabitEthernet0/2 no ip address shutdown duplex auto speed auto ! ! interface FastEthernet0/3/0 ! ! interface FastEthernet0/3/1 ! ! interface FastEthernet0/3/2 ! ! interface FastEthernet0/3/3 ! ! interface FastEthernet0/3/4 ! ! interface FastEthernet0/3/5 ! ! interface FastEthernet0/3/6 ! ! interface FastEthernet0/3/7 ! ! interface FastEthernet0/3/8 ! ! interface SM1/0 ip address 192.168.75.5 255.255.255.0 ip nat inside ip virtual-reassembly service-module fail-open service-module ip address 192.168.75.98 255.255.255.0 service-module ip default-gateway 192.168.75.99 ! ! interface SM1/1 no ip address ! ! interface Cellular0/1/0 no ip address encapsulation ppp ! ! interface Vlan1 no ip address ! ! ip forward-protocol nd ! no ip http server no ip http secure-server ! ip nat inside source static 192.168.75.6 10.11.16.98 ip nat inside source static 192.168.75.5 10.11.16.99 ! ! ! ! ! ! ! control-plane ! ! ! line con 0 line aux 0 line 0/1/0 no exec line 67 no activation-character no exec transport preferred none transport input all transport output pad telnet rlogin lapb-ta mop udptn v120 ssh stopbits 1 flowcontrol software line vty 0 4 login ! scheduler allocate 20000 1000 end Router#
	Sign in to vote. Flag Please sign in to flag this as inappropriate. Top

Radhika Miriyala Posts: 174 Join Date: 8/12/10 Recent Posts	RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - S Answer 4/19/11 6:34 PM as a reply to SCOTT PITTS. Mark as an Answer Submit Reply with Quote Quick Reply Scott, Thanks for the logs. It looks like a key verification issue. One thing I noticed is in step 4 of the sre install it writes a key file into the flash and in your case the key size is 919 but it should be 916 bytes. Can you please download the key file (sre-v-k9.smv.1.0.0.19.key )may be even the whole package once again and try? How are you copying the files to your ftp server. Thanks
	Sign in to vote. Flag Please sign in to flag this as inappropriate. Top

Ashwin Venkatesan Posts: 36 Join Date: 8/12/10 Recent Posts	RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - S Answer 4/19/11 6:35 PM as a reply to SCOTT PITTS. Mark as an Answer Submit Reply with Quote Quick Reply Hi Scott, Can you check if you have the key file (sre-v-k9.smv.x.x.x..key in your ftp server). If you have it can you recopy the file and try again Thanks, Ashwin
	Sign in to vote. Flag Please sign in to flag this as inappropriate. Top

Anurag Gurtu Posts: 62 Join Date: 4/2/08 Recent Posts	RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - S Answer 11/20/10 7:33 AM as a reply to SCOTT PITTS. Mark as an Answer Submit Reply with Quote Quick Reply I will also suggest you to upgrade the IOS image to the one uploaded on CDN and then configure service-module mgf ip address and gateway. -Anurag
	Sign in to vote. Flag Please sign in to flag this as inappropriate. Top

SCOTT PITTS Posts: 47 Join Date: 9/1/10 Recent Posts	RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - S Answer 11/20/10 7:33 AM as a reply to Anurag Gurtu. Mark as an Answer Submit Reply with Quote Quick Reply I will also suggest you to upgrade the IOS image to the one uploaded on CDN and then configure service-module mgf ip address and gateway. -Anurag The FTP server is a windows box (CiscoWorks) with FTP and TFTP. I downloaded if from the console this time. Within Winzip is sais the key file is 916 bytes but once it is extracted it is 919bytes. The first time it was extracted on my workstation and copied via a file share. Re-downloading did not make a difference. I have the Beta 2911 image on another 2911 and it performs the same way, just dont have to NAT it.
	Sign in to vote. Flag Please sign in to flag this as inappropriate. Top

Brett Tiller Posts: 114 Join Date: 4/9/08 Recent Posts	RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - S Answer 4/19/11 6:36 PM as a reply to SCOTT PITTS. Mark as an Answer Submit Reply with Quote Quick Reply Hi Scott, When using Winzip to extract files be sure to turn off the Smart Tar feature or it can corrupt files. Here's some more information on it. http://developer.cisco.com/web/axp/blogroll/-/blogs/be-careful-with-winzip?_33_redirect=%2Fweb%2Faxp%2Fblogroll Thanks, Brett Custom Application Engineer http://developer.cisco.com/web/axp/home
	Sign in to vote. Flag Please sign in to flag this as inappropriate. Top

SCOTT PITTS Posts: 47 Join Date: 9/1/10 Recent Posts	RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - S Answer 11/20/10 7:33 AM as a reply to Brett Tiller. Mark as an Answer Submit Reply with Quote Quick Reply It would appear that WinZip was the culpret but I still can not load the SRE. Now it download everything and reboots and then fails installing the package because it can not reach the FTP server, although it just pulled all those files from it.
	Sign in to vote. Flag Please sign in to flag this as inappropriate. Top

Brett Tiller Posts: 114 Join Date: 4/9/08 Recent Posts	RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - S Answer 4/19/11 6:37 PM as a reply to SCOTT PITTS. Mark as an Answer Submit Reply with Quote Quick Reply Scott, Glad we got one issue figured out. Please include the messages being displayed so we can analyze exactly what is occurring on your system. Thanks, Brett Custom Application Engineer http://developer.cisco.com/web/axp/home
	Sign in to vote. Flag Please sign in to flag this as inappropriate. Top

SCOTT PITTS Posts: 47 Join Date: 9/1/10 Recent Posts	RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - S Answer 11/20/10 7:33 AM as a reply to Brett Tiller. Mark as an Answer Submit Reply with Quote Quick Reply It is really is ugly that I had to route a network to the router just to load the SRE, but it appears to be the only way as my attempt to NAT did not work. I used the config another post on this forum and left of the VLANs and routed the network to the module. I then tried to load the SRE again. It appears to have done something different and may have even loaded the ESXi image. Seems to be stuck on loading MgmtVM, but maybe it is up and running. rbcp: INFO rbcp daemon output module = 4 rbcp: INFO rbcp daemon output product/name doesn't exist rbcp: INFO rbcp daemon output bryce registration message information: rbcp: INFO rbcp daemon output length: (89,1493172224), version (1,0), app_name(Cisco Foundation Software), app_ver(1.0), subsys_id (0), app_status (FNDN Running on SM), capability (1289), app_cookie_id (SM-SRE-900-K9) rbcp: INFO rbcp daemon output rbcp_dump raw message: sent, opcode = 0x13 rbcp: INFO rbcp daemon output rbcp_dump: 0x0e 0xff 0x00 0x5d 0x01 0x00 0x00 0x13 0xb0 0xd7 0x04 0x08 0xb0 0xd7 0x04 0x08 rbcp: INFO rbcp daemon output rbcp_dump: 0x00 0x00 0x00 0x59 0x54 0x4c 0x56 0x2d 0x54 0x59 0x50 0x45 0x01 0x00 0x10 0x19 rbcp: INFO rbcp daemon output rbcp_dump: 0x43 0x69 0x73 0x63 0x6f 0x20 0x46 0x6f 0x75 0x6e 0x64 0x61 0x74 0x69 0x6f 0x6e rbcp: INFO rbcp daemon output rbcp_dump: 0x20 0x53 0x6f 0x66 0x74 0x77 0x61 0x72 0x65 0x20 0x03 0x31 0x2e 0x30 0x30 0x01 rbcp: INFO rbcp daemon output rbcp_dump: 0x00 0x40 0x00 0x00 0x00 0x12 0x46 0x4e 0x44 0x4e 0x20 0x52 0x75 0x6e 0x6e 0x69 rbcp: INFO rbcp daemon output rbcp_dump: 0x6e 0x67 0x20 0x6f 0x6e 0x20 0x53 0x4d 0x50 0x04 0x00 0x00 0x05 0x09 0x60 0x0d rbcp: INFO rbcp daemon output rbcp_dump: 0x53 0x4d 0x2d 0x53 0x52 0x45 0x2d 0x39 0x30 0x30 0x2d 0x4b 0x39 rbcp: INFO rbcp daemon output current platform sm rbcp: INFO rbcp daemon output app_cookie_id from sysdb = SM-SRE-900-K9 rbcp: INFO rbcp daemon output ios_image_type1 from sysdb = 0 rbcp: INFO rbcp daemon output ios_image_type2 from sysdb = 0 rbcp: INFO rbcp daemon output app_capability from sysdb = 1289 rbcp: INFO rbcp daemon output subsys_id from sysdb = 0 rbcp: INFO rbcp daemon output rsrcmgr: moduleplatno: 4 rbcp: INFO rbcp daemon output rsrcmgr: rbcpmsg_fmt: 1 rbcp: INFO rbcp daemon output rbcp_register - SCP register, Version 2.6.22.10-vs2.2.0.5-cisco-smv rbcp: INFO rbcp daemon output Copyright (c) 1999-2009 by Cisco Systems, Inc. rbcp: INFO rbcp daemon output All rights reserved. rbcp: INFO rbcp daemon output product/name doesn't exist rbcp: INFO rbcp daemon output module type is 4 rbcp: INFO rbcp daemon output got configured variables: rbcp: INFO rbcp daemon output ios_image_type1 = 0 rbcp: INFO rbcp daemon output ios_image_type2 = 0 rbcp: INFO rbcp daemon output capability = 1289 rbcp: INFO rbcp daemon output subsys_id = 0 rbcp: INFO rbcp daemon output app_cookie_id = SM-SRE-900-K9 rbcp: INFO rbcp daemon output module = 4 add_file /mnt/dwnld/pkgdata/sre-v-k9.smv.1.0.0.19.pkg 8 /mivmdk sw/installed/manifest/installer_manifest.sig none rbcp: INFO rbcp daemon output product/name doesn't exist rbcp: INFO rbcp daemon output bryce registration message information: rbcp: INFO rbcp daemon output length: (89,1493172224), version (1,0), app_name(Cisco Foundation Software), app_ver(1.0), subsys_id (0), app_status (FNDN Running on SM), capability (1289), app_cookie_id (SM-SRE-900-K9) rbcp: INFO rbcp daemon output rbcp_dump raw message: sent, opcode = 0x13 rbcp: INFO rbcp daemon output rbcp_dump: 0x0e 0xff 0x00 0x5d 0x01 0x00 0x00 0x13 0xb0 0xd7 0x04 0x08 0xb0 0xd7 0x04 0x08 rbcp: INFO rbcp daemon output rbcp_dump: 0x00 0x00 0x00 0x59 0x54 0x4c 0x56 0x2d 0x54 0x59 0x50 0x45 0x01 0x00 0x10 0x19 rbcp: INFO rbcp daemon output rbcp_dump: 0x43 0x69 0x73 0x63 0x6f 0x20 0x46 0x6f 0x75 0x6e 0x64 0x61 0x74 0x69 0x6f 0x6e rbcp: INFO rbcp daemon output rbcp_dump: 0x20 0x53 0x6f 0x66 0x74 0x77 0x61 0x72 0x65 0x20 0x03 0x31 0x2e 0x30 0x30 0x01 rbcp: INFO rbcp daemon output rbcp_dump: 0x00 0x40 0x00 0x00 0x00 0x12 0x46 0x4e 0x44 0x4e 0x20 0x52 0x75 0x6e 0x6e 0x69 rbcp: INFO rbcp daemon output rbcp_dump: 0x6e 0x67 0x20 0x6f 0x6e 0x20 0x53 0x4d 0x50 0x04 0x00 0x00 0x05 0x09 0x60 0x0d rbcp: INFO rbcp daemon output rbcp_dump: 0x53 0x4d 0x2d 0x53 0x52 0x45 0x2d 0x39 0x30 0x30 0x2d 0x4b 0x39 rbcp: INFO rbcp daemon output current platform sm rbcp: INFO rbcp daemon output app_cookie_id from sysdb = SM-SRE-900-K9 rbcp: INFO rbcp daemon output ios_image_type1 from sysdb = 0 rbcp: INFO rbcp daemon output ios_image_type2 from sysdb = 0 rbcp: INFO rbcp daemon output app_capability from sysdb = 1289 rbcp: INFO rbcp daemon output subsys_id from sysdb = 0 rbcp: INFO rbcp daemon output rsrcmgr: moduleplatno: 4 rbcp: INFO rbcp daemon output rsrcmgr: rbcpmsg_fmt: 1 rbcp: INFO rbcp daemon output rbcp_register - SCP register, Version 2.6.22.10-vs2.2.0.5-cisco-smv rbcp: INFO rbcp daemon output Copyright (c) 1999-2009 by Cisco Systems, Inc. rbcp: INFO rbcp daemon output All rights reserved. rbcp: INFO rbcp daemon output product/name doesn't exist rbcp: INFO rbcp daemon output module type is 4 rbcp: INFO rbcp daemon output got configured variables: rbcp: INFO rbcp daemon output ios_image_type1 = 0 rbcp: INFO rbcp daemon output ios_image_type2 = 0 rbcp: INFO rbcp daemon output capability = 1289 rbcp: INFO rbcp daemon output subsys_id = 0 rbcp: INFO rbcp daemon output app_cookie_id = SM-SRE-900-K9 rbcp: INFO rbcp daemon output module = 4 rbcp: INFO rbcp daemon output product/name doesn't exist rbcp: INFO rbcp daemon output bryce registration message information: rbcp: INFO rbcp daemon output length: (89,1493172224), version (1,0), app_name(Cisco Foundation Software), app_ver(1.0), subsys_id (0), app_status (FNDN Running on SM), capability (1289), app_cookie_id (SM-SRE-900-K9) rbcp: INFO rbcp daemon output rbcp_dump raw message: sent, opcode = 0x13 rbcp: INFO rbcp daemon output rbcp_dump: 0x0e 0xff 0x00 0x5d 0x01 0x00 0x00 0x13 0xb0 0xd7 0x04 0x08 0xb0 0xd7 0x04 0x08 rbcp: INFO rbcp daemon output rbcp_dump: 0x00 0x00 0x00 0x59 0x54 0x4c 0x56 0x2d 0x54 0x59 0x50 0x45 0x01 0x00 0x10 0x19 rbcp: INFO rbcp daemon output rbcp_dump: 0x43 0x69 0x73 0x63 0x6f 0x20 0x46 0x6f 0x75 0x6e 0x64 0x61 0x74 0x69 0x6f 0x6e rbcp: INFO rbcp daemon output rbcp_dump: 0x20 0x53 0x6f 0x66 0x74 0x77 0x61 0x72 0x65 0x20 0x03 0x31 0x2e 0x30 0x30 0x01 rbcp: INFO rbcp daemon output rbcp_dump: 0x00 0x40 0x00 0x00 0x00 0x12 0x46 0x4e 0x44 0x4e 0x20 0x52 0x75 0x6e 0x6e 0x69 rbcp: INFO rbcp daemon output rbcp_dump: 0x6e 0x67 0x20 0x6f 0x6e 0x20 0x53 0x4d 0x50 0x04 0x00 0x00 0x05 0x09 0x60 0x0d add_file /mnt/dwnld/pkgdata/sre-v-k9.smv.1.0.0.19.pkg 4 /mivmdk sw/installed/manifest/oscore_manifest.sig none rbcp: INFO rbcp daemon output rbcp_dump: 0x53 0x4d 0x2d 0x53 0x52 0x45 0x2d 0x39 0x30 0x30 0x2d 0x4b 0x39 rbcp: INFO rbcp daemon output current platform sm rbcp: INFO rbcp daemon output app_cookie_id from sysdb = SM-SRE-900-K9 rbcp: INFO rbcp daemon output ios_image_type1 from sysdb = 0 rbcp: INFO rbcp daemon output ios_image_type2 from sysdb = 0 rbcp: INFO rbcp daemon output app_capability from sysdb = 1289 rbcp: INFO rbcp daemon output subsys_id from sysdb = 0 rbcp: INFO rbcp daemon output rsrcmgr: moduleplatno: 4 rbcp: INFO rbcp daemon output rsrcmgr: rbcpmsg_fmt: 1 rbcp: INFO rbcp daemon output rbcp_register - SCP register, Version 2.6.22.10-vs2.2.0.5-cisco-smv rbcp: INFO rbcp daemon output Copyright (c) 1999-2009 by Cisco Systems, Inc. rbcp: INFO rbcp daemon output All rights reserved. rbcp: INFO rbcp daemon output product/name doesn't exist rbcp: INFO rbcp daemon output module type is 4 rbcp: INFO rbcp daemon output got configured variables: rbcp: INFO rbcp daemon output ios_image_type1 = 0 rbcp: INFO rbcp daemon output ios_image_type2 = 0 rbcp: INFO rbcp daemon output capability = 1289 rbcp: INFO rbcp daemon output subsys_id = 0 rbcp: INFO rbcp daemon output app_cookie_id = SM-SRE-900-K9 rbcp: INFO rbcp daemon output module = 4 rbcp: INFO rbcp daemon output product/name doesn't exist rbcp: INFO rbcp daemon output bryce registration message information: rbcp: INFO rbcp daemon output length: (89,1493172224), version (1,0), app_name(Cisco Foundation Software), app_ver(1.0), subsys_id (0), app_status (FNDN Running on SM), capability (1289), app_cookie_id (SM-SRE-900-K9) INIT: Sending processes the TERM signalump raw Rebooting ... shutdown: sending all processes the TERM signal... rbcp: INFO rbcp daemon output END shutdown: sending all processes the KILL signal. shutdown: turning off swap shutdown: unmounting all file systems Please stand by while rebooting the system. Restarting system. Sep 9 13:06:20.771: %SM_INSTALL-6-INST_SUCC: SM1/0 SUCCESS: install-completed. Install successful on SM1/0 Initializing memory #1. Please wait... Initializing memory #2. Please wait... This may take a minute.... Serial ATA Port 0 : Hitachi HTE545050B9A300 Serial ATA Port 1 : Hitachi HTE545050B9A300 DDR Memory 4096 MB detected Intel(R) Core(TM)2 Duo CPU L9400 @ 1.86GHz BIOS SM 3.52.6, BIOS Build date: 08/03/2010 Intel(R) Core(TM)2 Duo CPU L9400 @ 1.86GHz BIOS SM 3.52.6, BIOS Build date: 08/03/2010 System now booting... Please wait... Please press P to select Primary Boot Loader ... or S to select Secondary Boot Loader ... or wait to boot from default configuration ... ....................................................................................................... SRE module get located and run.... New SRE installation detected.... Now booting from secondary boot loader.... Authenticating boot loader.... Secondary Boot Loader authenticated - booting.... Updating flash with bootloader configuration. Please wait .................. done. Updating flash with bootloader configuration. Please wait .................. done. Please enter '*' to change boot configuration: Sep 9 13:07:47.799: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Status Req Sep 9 13:07:47.799: %SM_INSTALL-6-RBIP_STATUS: SM1/0 RBIP status is at Secondary Bootloader Verified Copying to Primary. Detect and Initialze network device Backup current platform configurations.... SRE step 1 - SM registration... Response - no installation needed (len: 422) SRE Installation Not Needed Restoring orignial configuration... Updating flash with bootloader configuration. Please wait .................. done. Sep 9 13:07:53.739: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Requestgot meta list size: 3, 49, 96, 613 Verifying ... Upgrading...Primary Bootloader done. Starting Kernel. Starting VMKernel initialization ... Initializing memory ... Initializing chipset ... Initializing timing ... Initializing scheduler ... Initializing device support ... Initializing processors ... Initializing interrupts ... Initializing IOV ... Initializing chipset IOAPIC ... Enabling interrupts ... Initializing ACPI ... Initializing Power Management ... VMKernel loaded successfully. Loading module procfs ... procfs loaded successfully. Loading module vmkapiv1_0_0_0_vmkernel_shim ... vmkapiv1_0_0_0_vmkernel_shim loaded successfully. Loading module vmklinux ... vmklinux loaded successfully. Loading module random ... random loaded successfully. Loading module usb ... usb loaded successfully. Loading module ehci-hcd ... ehci-hcd loaded successfully. Loading module usb-uhci ... usb-uhci loaded successfully. Loading module hid ... hid loaded successfully. Loading module dm ... dm loaded successfully. Loading module nmp ... nmp loaded successfully. Loading module vmw_satp_local ... vmw_satp_local loaded successfully. Loading module vmw_satp_default_aa ... vmw_satp_default_aa loaded successfully. Loading module vmw_psp_lib ... vmw_psp_lib loaded successfully. Loading module vmw_psp_fixed ... vmw_psp_fixed loaded successfully. Loading module vmw_psp_rr ... vmw_psp_rr loaded successfully. Loading module vmw_psp_mru ... vmw_psp_mru loaded successfully. Loading module vmw_psp_fixed_ap ... vmw_psp_fixed_ap loaded successfully. Loading module vmw_satp_alua ... vmw_satp_alua loaded successfully. Loading module vmw_satp_cx ... vmw_satp_cx loaded successfully. Loading module libata ... libata loaded successfully. Loading module usb-storage ... usb-storage loaded successfully. Loading module vfat ... vfat loaded successfully. Loading module mask_path_plugin ... mask_path_plugin loaded successfully. Loading module vaai_filter ... vaai_filter loaded successfully. Loading module vmw_vaaip_emc ... vmw_vaaip_emc loaded successfully. Loading module vmkapiv1_0_0_0_nmp_shim ... vmkapiv1_0_0_0_nmp_shim loaded successfully. Loading module vtddmar ... vtddmar loaded successfully. Loading module vmci ... vmci loaded successfully. Loading module iscsi_trans ... iscsi_trans loaded successfully. Loading module hub ... hub loaded successfully. Loading module netsched ... netsched loaded successfully. Loading module e1000e ... e1000e loaded successfully. Loading module bnx2 ... bnx2 loaded successfully. Loading module cnic ... cnic loaded successfully. Loading module iscsi_linux ... iscsi_linux loaded successfully. Loading module bnx2i ... bnx2i loaded successfully. Loading module ata_piix ... ata_piix loaded successfully. Loading module lvmdriver ... lvmdriver loaded successfully. Loading module deltadisk ... deltadisk loaded successfully. Loading module multiextent ... multiextent loaded successfully. Loading module dvsdev ... dvsdev loaded successfully. Loading module etherswitch ... etherswitch loaded successfully. Loading module shaper ... shaper loaded successfully. Loading module cdp ... cdp loaded successfully. Loading module tcpip3 ... tcpip3 loaded successfully. Loading module dvfilter ... dvfilter loaded successfully. Loading module vmkapiv1_0_0_0_dvfilter_shim ... vmkapiv1_0_0_0_dvfilter_shim loaded successfully. Loading module vmkibft ... vmkibft loaded successfully. Loading module vmfs3 ... vmfs3 loaded successfully. Loading module nfsclient ... nfsclient loaded successfully. Loading module vmkstatelogger ... vmkstatelogger loaded successfully. Loading module migrate ... migrate loaded successfully. Loading module cbt ... cbt loaded successfully. Loading module spi ... spi loaded successfully. Running ntpd start Running DCUI start Running vprobed start Running vobd start Running storageRM start Running sensord start Running lbtd start Running hostd start Running slpd start Running wsman start Running usbarbitrator start Running sfcbd-watchdog start Running cisco-agent start cisco-agent: Starting first boot procedure cisco-agent: Verifying Cisco MgmtVM H/G vSwitch & portgroup cisco-agent: Verifying Cisco MgmtVM network cisco-agent: Verifying Cisco MGF network cisco-agent: Starting Cisco MgmtVM
	Sign in to vote. Flag Please sign in to flag this as inappropriate. Top

Anurag Gurtu Posts: 62 Join Date: 4/2/08 Recent Posts	RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - S Answer 11/20/10 7:33 AM as a reply to SCOTT PITTS. Mark as an Answer Submit Reply with Quote Quick Reply We currently have a know issue which we are working on where sometimes the loading stops at Management VM. Please issue the following command from IOS Service-module sm X/0 reset This will reset the module and upon reload it shouldn¿t get stuck at management VM. If it does, please issue reset once again. This issue will be fixed very soon. I would like to understand why you are setting up additional routes on the router for SRE installation. Is it due to the fact that FTP server is on a network which is not reachable by SRE?
	Sign in to vote. Flag Please sign in to flag this as inappropriate. Top

SCOTT PITTS Posts: 47 Join Date: 9/1/10 Recent Posts	RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - S Answer 11/20/10 7:33 AM as a reply to Anurag Gurtu. Mark as an Answer Submit Reply with Quote Quick Reply I would like to understand why you are setting up additional routes on the router for SRE installation. Is it due to the fact that FTP server is on a network which is not reachable by SRE? The FTP server in not on the same network as the as the GIG0/0 interface. It is a routing issue because I could not seem to get the SRE to be on the same network as the GIG0/0 interface. I tried to put it on an 192.168.75.X network and NAT it to the 10.11.17.x network on GIG0/0. It would load the initial config rebot and then the code install would fail as it could not get to the FTP server.
	Sign in to vote. Flag Please sign in to flag this as inappropriate. Top

SCOTT PITTS Posts: 47 Join Date: 9/1/10 Recent Posts	RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - S Answer 11/20/10 7:33 AM as a reply to Anurag Gurtu. Mark as an Answer Submit Reply with Quote Quick Reply We currently have a know issue which we are working on where sometimes the loading stops at Management VM. Please issue the following command from IOS Service-module sm X/0 reset This seems to have gotten the SRE back up and running the ESXi image: Router#SERVice-module SM 1/0 STATUS Service Module is Cisco SM1/0 Service Module supports session via TTY line 67 Service Module is in Steady state Service Module heartbeat-reset is enabled Getting status from the Service Module, please wait.. Cisco SRE-V Software 1.0.0.19 SRE-V Running on SMV No install/uninstall in progress Router# Per the SRE document I should be able to go to the SRE's MGF interface to get the vSpere Client via https. Https does not return anything and http returns a 404 error http://192.168.75.51 <h1>HTTP Status 404 - /admin</h1> <hr size="1" noshade="noshade" /> type Status report message /admin description The requested resource (/admin) is not available. <hr size="1" noshade="noshade" /> <h3>Apache Tomcat/6.0-snapshot</h3> How do I begin managing the ESXi?
	Sign in to vote. Flag Please sign in to flag this as inappropriate. Top

Radhika Miriyala Posts: 174 Join Date: 8/12/10 Recent Posts	RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - S Answer 11/20/10 7:33 AM as a reply to SCOTT PITTS. Mark as an Answer Submit Reply with Quote Quick Reply Scott, Did you activate the license on the SRE? Can you also please give me the output of cli ¿show hypervisor ip¿ Thanks, Radhika From: Cisco Developer Community Forums [mailto:cdicuser@developer.cisco.com] Sent: Thursday, September 09, 2010 9:47 AM To: cdicuser@developer.cisco.com Subject: New Message from SCOTT PITTS in Service Ready Engine Virtualization - SRE-V Beta Testing: RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - S SCOTT PITTS has created a new message in the forum "SRE-V Beta Testing": -------------------------------------------------------------- We currently have a know issue which we are working on where sometimes the loading stops at Management VM. Please issue the following command from IOS Service-module sm X/0 reset This seems to have gotten the SRE back up and running the ESXi image: Router#SERVice-module SM 1/0 STATUS Service Module is Cisco SM1/0 Service Module supports session via TTY line 67 Service Module is in Steady state Service Module heartbeat-reset is enabled Getting status from the Service Module, please wait.. Cisco SRE-V Software 1.0.0.19 SRE-V Running on SMV No install/uninstall in progress Router# Per the SRE document I should be able to go to the SRE's MGF interface to get the vSpere Client via https. Https does not return anything and http returns a 404 error http://192.168.75.51 <h1>HTTP Status 404 - /admin</h1> <hr size="1" noshade="noshade" /> type Status report message /admin description The requested resource (/admin) is not available. <hr size="1" noshade="noshade" /> <h3>Apache Tomcat/6.0-snapshot</h3> How do I begin managing the ESXi? -- To respond to this post, please click the following link: <http://developer.cisco.com/group/srev/forums/-/message_boards/message/2519349> or simply reply to this email.
	Sign in to vote. Flag Please sign in to flag this as inappropriate. Top

SCOTT PITTS Posts: 47 Join Date: 9/1/10 Recent Posts	RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - S Answer 11/20/10 7:33 AM as a reply to Radhika Miriyala. Mark as an Answer Submit Reply with Quote Quick Reply Scott, Did you activate the license on the SRE? Can you also please give me the output of cli ¿show hypervisor ip¿ Thanks, Radhika That is interesting as it would appear to not have an IP. I did accept the license. I also can not reload or reset the module and it seen to go into some loop. I have to power cycle the router to get the SRE back running. se-192-168-75-51# show hypervisor ip Hostname: localhost Domain Name: None IP Config: 169.254.0.1(Subnet Mask: 255.255.0.0) 169.254.1.1(Subnet Mask: 255.255.255.0) Default Gateway: None Preferred DNS Server: None Alternative DNS Server: None se-192-168-75-51# show license Index 0 Feature: VMIVR-VM-MBX Period left: 8 weeks 4 days License Type: Evaluation License State: Active, Not in Use, EULA not accepted License Count: 250 / 0 License Priority: None Index 1 Feature: TEST_APP1 Period left: 1 hour 0 minute License Type: Evaluation License State: Active, Not in Use, EULA not accepted License Count: Non-Counted License Priority: None Index 2 Feature: TEST_APP2 Period left: 1 day 1 hour License Type: Evaluation License State: Active, Not in Use, EULA not accepted License Count: Non-Counted License Priority: None Index 3 Feature: TEST_APP3 Period left: 1 week 0 day License Type: Evaluation License State: Active, Not in Use, EULA not accepted License Count: Non-Counted License Priority: None Index 4 Feature: TEST_CAPP1 Period left: 1 hour 0 minute License Type: Evaluation License State: Active, Not in Use, EULA not accepted License Count: 250 / 0 License Priority: None Index 5 Feature: TEST_CAPP2 Period left: 1 day 1 hour License Type: Evaluation License State: Active, Not in Use, EULA not accepted License Count: 250 / 0 License Priority: None Index 6 Feature: TEST_CAPP3 Period left: 1 hour 0 minute License Type: Evaluation License State: Active, Not in Use, EULA not accepted License Count: 24 / 0 License Priority: None Index 7 Feature: TEST_CAPP4 Period left: 1 day 1 hour License Type: Evaluation License State: Active, Not in Use, EULA not accepted License Count: 24 / 0 License Priority: None Index 8 Feature: SRE-V-HOST-LIC Period left: 8 weeks 3 days License Type: Evaluation License State: Active, In Use License Count: Non-Counted License Priority: Low se-192-168-75-51# *** Reloading ** se-192-168-75-51# reload Reloading the system will terminate all end user sessions. Doing a reload will cause any unsaved configuration data to be lost. Are you sure you want to reload? se-192-168-75-51# MONITOR SHUTDOWN... INIT: Sending processes the TERM signal Shutting down ... rbcp: INFO rbcp daemon output END trace: INFO trace daemon output END platform.config: INFO platform.config server output END Power down. acpi_power_off called Starting VMKernel shutdown ... Shutting down file systems drivers ... Stopping SCSI Device periodic probe and disabling path probe ... Shutting down network devices ... Shutting down device drivers ... Shutting down APs ... Sep 9 16:55:34.491: %LINK-3-UPDOWN: Interface SM1/1, changed state to down Sep 9 16:55:35.491: %LINEPROTO-5-UPDOWN: Line protocol on Interface SM1/1, changed state to down Initializing memory #1. Please wait... Initializing memory #2. Please wait... This may take a minute.... Sep 9 16:55:39.491: %LINK-3-UPDOWN: Interface SM1/1, changed state to up Sep 9 16:55:40.491: %LINEPROTO-5-UPDOWN: Line protocol on Interface SM1/1, changed state to up Serial ATA Port 0 : Hitachi HTE545050B9A300 Serial ATA Port 1 : Hitachi HTE545050B9A300 DDR Memory 4096 MB detected Intel(R) Core(TM)2 Duo CPU L9400 @ 1.86GHz BIOS SM 3.52.6, BIOS Build date: 08/03/2010 Intel(R) Core(TM)2 Duo CPU L9400 @ 1.86GHz BIOS SM 3.52.6, BIOS Build date: 08/03/2010 System now booting... Please wait... Please press P to select Primary Boot Loader ... or S to select Secondary Boot Loader ... or wait to boot from default configuration ... ....................................................................................................... SRE module get located and run.... Now booting from secondary boot loader.... Authenticating boot loader.... Secondary Boot Loader authenticated - booting.... Please enter '**' to change boot configuration: Detect and Initialze network device Backup current platform configurations.... SRE step 1 - SM registration... Sep 9 16:56:33.251: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request Time-out from RBIP response wait loop Sep 9 16:56:53.071: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request Time-out from RBIP response wait loop Sep 9 16:57:12.899: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request Time-out from RBIP response wait loop Sep 9 16:57:32.727: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request Time-out from RBIP response wait loop Sep 9 16:57:52.555: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request Time-out from RBIP response wait loop Sep 9 16:58:12.379: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request Time-out from RBIP response wait loop Sep 9 16:58:32.207: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request Time-out from RBIP response wait loop Sep 9 16:58:52.035: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request Time-out from RBIP response wait loop Sep 9 16:59:11.863: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request Time-out from RBIP response wait loop Sep 9 16:59:31.691: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request Time-out from RBIP response wait loop Sep 9 16:59:51.519: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request Time-out from RBIP response wait loop Sep 9 17:00:11.347: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request Time-out from RBIP response wait loop Sep 9 17:00:31.175: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request Router#SERVice-module SM 1/0 reset Use reset only to recover from shutdown or failed state Warning: May lose data on the the NVRAM, nonvolatile file system or unsaved configuration! Do you want to reset? Sep 9 17:00:51.003: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request Trying to reload Service Module SM1/0. Router# [Resuming connection 1 to 192.168.75.50 ... ] Time-out from RBIP response wait loop Serial ATA Port 0 : Hitachi HTE545050B9A300 Serial ATA Port 1 : Hitachi HTE545050B9A300 DDR Memory 4096 MB detected Intel(R) Core(TM)2 Duo CPU L9400 @ 1.86GHz BIOS SM 3.52.6, BIOS Build date: 08/03/2010 Intel(R) Core(TM)2 Duo CPU L9400 @ 1.86GHz BIOS SM 3.52.6, BIOS Build date: 08/03/2010 System now booting... Please wait... Please press P to select Primary Boot Loader ... or S to select Secondary Boot Loader ... or wait to boot from default configuration ... ....................................................................................................... SRE module get located and run.... Now booting from secondary boot loader.... Authenticating boot loader.... Secondary Boot Loader authenticated - booting.... Please enter '*' to change boot configuration: Detect and Initialze network device Backup current platform configurations.... SRE step 1 - SM registration... Sep 9 17:01:54.255: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request Time-out from RBIP response wait loop *Sep 9 17:02:14.067: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration Request
	Sign in to vote. Flag Please sign in to flag this as inappropriate. Top

Radhika Miriyala Posts: 174 Join Date: 8/12/10 Recent Posts	RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - S Answer 4/19/11 6:39 PM as a reply to SCOTT PITTS. Mark as an Answer Submit Reply with Quote Quick Reply Scott, This seems to be an issue with the Config for the MGF on the IOS side. Can you please give the output of the cli ¿show running-config¿ from the router ? Thanks, Radhika
	Sign in to vote. Flag Please sign in to flag this as inappropriate. Top

SCOTT PITTS Posts: 47 Join Date: 9/1/10 Recent Posts	RE: New Message from SCOTT PITTS in Service Ready Engine Virtualization - S Answer 11/20/10 7:33 AM as a reply to Radhika Miriyala. Mark as an Answer Submit Reply with Quote Quick Reply Router#show config Using 1900 out of 262136 bytes ! ! Last configuration change at 21:06:21 UTC Wed Sep 8 2010 ! version 15.0 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Router ! boot-start-marker boot-end-marker ! ! no aaa new-model ! ! ! memory-size iomem 20 ! no ipv6 cef ip source-route ip cef ! ! ! ! ! multilink bundle-name authenticated ! ! ! ! license udi pid CISCO2911/K9 sn FTX1429A35B hw-module sm 1 ! ! ! vtp version 2 ! redundancy ! ! ! ! ! ! ! ! ! interface GigabitEthernet0/0 ip address 10.11.16.99 255.255.240.0 ip nat outside ip virtual-reassembly duplex auto speed auto ! ! interface GigabitEthernet0/1 no ip address shutdown duplex auto speed auto ! ! interface GigabitEthernet0/2 no ip address shutdown duplex auto speed auto ! ! interface FastEthernet0/3/0 ! ! interface FastEthernet0/3/1 ! ! interface FastEthernet0/3/2 ! ! interface FastEthernet0/3/3 ! ! interface FastEthernet0/3/4 ! ! interface FastEthernet0/3/5 ! ! interface FastEthernet0/3/6 ! ! interface FastEthernet0/3/7 ! ! interface FastEthernet0/3/8 ! ! interface SM1/0 ip address 192.168.75.50 255.255.255.0 ip nat inside ip virtual-reassembly service-module ip address 192.168.75.51 255.255.255.0 !Application: FNDN Running on SM service-module ip default-gateway 192.168.75.50 ! ! interface SM1/1 no ip address ! ! interface Cellular0/1/0 no ip address encapsulation ppp ! ! interface Vlan1 no ip address ! ! ip forward-protocol nd ! no ip http server no ip http secure-server ! ip route 0.0.0.0 0.0.0.0 10.11.16.1 ! ! ! ! ! ! ! control-plane ! ! ! line con 0 line aux 0 line 0/1/0 no exec speed 144000 line 67 no activation-character no exec transport preferred none transport input all transport output pad telnet rlogin lapb-ta mop udptn v120 ssh stopbits 1 flowcontrol software line vty 0 4 login ! scheduler allocate 20000 1000 end
	Sign in to vote. Flag Please sign in to flag this as inappropriate. Top

Showing 1 - 20 of 34 results.

First Previous Next Last