How to use internal interface for hypervisor http://developer.cisco.com/c/message_boards/find_thread?p_l_id=&threadId=5857279 2013-05-21T22:46:14Z 2013-05-21T22:46:14Z Ken Coley http://developer.cisco.com/c/message_boards/find_message?p_l_id=&messageId=5857293 2012-05-10T01:21:33Z 2012-05-10T01:21:33Z

Reboot the router made the ESXi config now work as well. Everything is back to the old mode. So I can restart testing tomorrow morning. -Ken

Ken Coley 2012-05-10T01:21:33Z Ken Coley http://developer.cisco.com/c/message_boards/find_message?p_l_id=&messageId=5857291 2012-05-09T19:37:28Z 2012-05-09T19:37:28Z

Ok, I will try this again. Thanks, Ken

Ken Coley 2012-05-09T19:37:28Z Brett Tiller http://developer.cisco.com/c/message_boards/find_message?p_l_id=&messageId=5857289 2012-05-09T19:35:30Z 2012-05-09T19:35:30Z

Ken, I've got vmnic0 set to IP 192.168.3.5. I've got my VM as 192.168.3.10. The VM resides with vmnic0. -Brett

Brett Tiller 2012-05-09T19:35:30Z Ken Coley http://developer.cisco.com/c/message_boards/find_message?p_l_id=&messageId=5857287 2012-05-09T19:34:08Z 2012-05-09T19:34:08Z

Manuka, I tried setting IP address to 192.168.1.252 and the gateway to 192.168.1.254 and it didn't work. I tried setting IP address to 192.168.5.253 and the gateway to 192.168.5.254 and that also didn't work. So I am at a loss on how it is supposed to work. -Ken

Ken Coley 2012-05-09T19:34:08Z Manuka Jayakody http://developer.cisco.com/c/message_boards/find_message?p_l_id=&messageId=5857285 2012-05-09T18:12:06Z 2012-05-09T18:12:06Z

Ken, Just to clarify. Do you have your ESXi default-gateway set to 192.168.5.254 ? -Manuka

Manuka Jayakody 2012-05-09T18:12:06Z Ken Coley http://developer.cisco.com/c/message_boards/find_message?p_l_id=&messageId=5857283 2012-05-09T17:10:39Z 2012-05-09T17:10:39Z

Brett, Thanks for the info, but what then is your ESXi settings? My BMC (or CIMC) works just fine, its the ESXi management console I can not get to remotely. -Ken

Ken Coley 2012-05-09T17:10:39Z Brett Tiller http://developer.cisco.com/c/message_boards/find_message?p_l_id=&messageId=5857281 2012-05-09T02:01:17Z 2012-05-09T02:01:17Z

Ken, I ran some tests in my lab. Your configuration looks correct; however I think your ethernet connections might be the issue. In my lab the M port on the UCSE server is connected to the switch. This connection keeps the BMC data separate and bypasses the router so that no cpu cycles are utlized on it for BMC processing. The default-gateway as you specified as 192.168.1.254 would be a router interface that is also connected to the switch as well. My interface configuration looks like: interface GigabitEthernet0/0 ip address 192.168.1.60 255.255.255.0 duplex auto speed auto no cdp enable interface ucse2/0 ip address 192.168.3.1 255.255.255.0 ip nat inside ip virtual-reassembly in imc ip address 192.168.1.61 255.255.255.0 default-gateway 192.168.1.60 imc access-port dedicated Please let me know if the wiring changes fix the issue. If this configuration doesn't suit your needs, please provide details of what you are trying to do. Thanks, Brett

Brett Tiller 2012-05-09T02:01:17Z Ken Coley http://developer.cisco.com/c/message_boards/find_message?p_l_id=&messageId=5857278 2012-06-12T19:47:46Z 2012-05-08T18:13:55Z

If I have the UCSE external interface being used for CIMC, can I still use the internal interface ucse2/0 for hypervisor management.  If so, then my config is:   interface ucse2/0  ip address 192.168.5.254 255.255.255.0  ip nat inside  ip virtual-reassembly in  imc ip address 192.168.1.253 255.255.255.0 default-gateway 192.168.1.254  imc access-port dedicated   But if I configure my ESXi vmnic0 to 192.168.5.253, it does not work.  Any suggestions.   -Ken

Ken Coley 2012-05-08T18:13:55Z