On CUBE, is it possible to accept a T38 fax on inbound SIP leg and send to MMOIP T37 store-and-forward to ESMTP server with PVDM2-64, but no TDM card?

I wish to port a hybrid TCL/vXML application from as5400hpx to CUBE (IPIPGW) on as5350xm (with PVDM2-64).  The existing application has T37 onramp functionality using same number for voice/fax (fax detection).  The onRamp fax works when the inbound leg is either TDM or SIP.

The CUBE does have one PVDM2-64, I will add more after initial development and testing.
The CUBE will NOT have any TDM cards, SIP only.

My initial tests have NOT been successful.  I will do more testing and post more details if someone can confirm this is even possible.

 
SHOW VER:

Cisco IOS Software, 5350 Software (C5350-JK9SU2_IVS-M), Version 12.4(24)T1, RELEASE SOFTWARE (fc3)
System image file is "flash:c5350-jk9su2_ivs-mz.124-24.T1.bin"

Cisco AS5350XM (BCM) processor (revision 0x22) with 786431K/262144K bytes of memory.
SB-1 CPU at 750MHz, Implementation 1025, Rev 0.3, 256KB L2 Cache
4 DSPs, 64 Voice resources
512K bytes of NVRAM.
 
 
CONFIG: 

voice-card 1
!
multilink bundle-name authenticated
!
voice service voip
 allow-connections sip to sip
 fax protocol t38 nse ls-redundancy 5 hs-redundancy 2 fallback pass-through g711ulaw
 sip
  rel1xx disable
!
application
  service faxTest http://luann/fax.vxml      <!-  luann does resolve properly and fax.vxml is accessible, no issue here (see below for fax.vxml) ->
 
fax receive called-subscriber PrivateFaxDelivery
fax interface-type fax-mail
mta send server luann port 25      <!-  luann does resolve properly and SMTM is accessible, no issue here ->
mta send with-subject $s$
mta send filename FAX
mta send postmaster postmaster@PrivateFaxDelivery.com
mta send mail-from hostname PrivateFaxDelivery.com
mta send mail-from username $s$
mta send return-receipt-to hostname PrivateFaxDelivery.com
mta send return-receipt-to username Fax@PrivateFaxDelivery.com
 
nls resp-timeout 1
cpd cr-id 1
!
mgcp fax t38 ecm
mgcp behavior g729-variants static-pt
 
dial-peer voice 10 voip
 service faxTest
 incoming called-number T
 codec g711ulaw
 fax protocol t38 ls-redundancy 5 hs-redundancy 2 fallback pass-through g711ulaw
!
dial-peer voice 30 mmoip
 description OUTBOUND FAX-2-EMAIL
 service fax_hop_on out-bound
 destination-pattern 99
 information-type fax
 session target mailto:$e$@PrivateFaxDelivery.com
!
 
--------------------------------
Script Name : fax
       URL  : http://luann/fax.vxml
       Type : Service
       State: Registered
       Life : Configured
       Exec Instances: 0

Script Code Begin:
--------------------------------
VXML Application fax
    URL=http://luann/fax.vxml
    Security Level: not trusted
            0 incoming calls
            0 calls handed off to it
            0 call transfers initiated
            0 pages loaded,  0 successful
            0 prompt play attempts, 0 successful
            0 recorded messages


The VXML Script is:
------------------
<?xml version="1.0" encoding="iso-8859-1"?>
<vxml version="2.0">
  <form>
    <transfer
                        name="mycall"
                        destexpr="'fax://99'"
                        bridge="false"
                        connecttimeout="15s"
                        maxtime="3600s"
                        cisco-mailtoaddress="session.telephone.dnis+'_'+session.telephone.ani" cisco-longpound="true"
                        cisco-desttype="2"
                        cisco-destplan="1" />
  </form>
</vxml>

Can it DETECT fax without using DSP/TDM ?
 
If so, can I SIP redirect the incoming leg to a TDM loop?
 
Also, you say "Don't think will work",  do you KNOW it won't work?
 
Travis

Right, let me ask again.


Is it possible to accept a T38 fax with DSP and without TDM card?

If not, can I detect the T38 fax on non-TDM IPIPGW and if fax detected, then redirect the incoming SIP leg to a fax server ?
 
If none of the above will work, can you please point me in the right direction using IPIPGW with some calls needing fax detection?