New and Changed Information

This section provides the list of new features for release 10.4(x).

Release 10.4(3)F

• Configuring ACLs

  • Disabling error-disabled State of an Ethernet Port
  • Disabling the errdisable detect cause for acl-exception

• Configuring ACLs

  • Enabling statistics per-entry for MPLS ACLs

• Configuring VXLAN OAM (NGOAM)

  • Enabling L3 loop-detection on ethernet Interfaces
  • Enabling L3 loop-detection on port-channel Interfaces
  • Displaying Loops Detected on L3 Interfaces

• Querying Configuration (Show Commands)

  • Querying MCAST NAT TCAM Resource Monitoring
  • Querying NBM TCAM Resource Monitoring

• Querying OSPFv3

• VXLAN EVPN Traffic Engineering - Multi-Site Egress Load-Balancing

• VXLAN EVPN Traffic Engineering – RPM support

• Micro-segmentation for VXLAN Fabrics Using Group Policy Option (GPO)

Release 10.4(2)F

• Configuring System Logging
  • Configuring Logging Level NVE
• Configuring TCAM
  • Configuring Hardware Rate Limiter
• Configuring TCAM
  • Configuring TCAM Region
• Configuring MACSec
  • Displaying MACsec Statistics
• Configuring SSH
  • Configuring SSH Algorithm
• Configuring a TCP-Connect Operation
  • Configuring Close-Connection Fin
• Configuring ARP
  • Configuring ARP Cache Limit Per SVI Interface

Release 10.4(1)F

• Configuring QoS Class Maps

  • Configuring Vxlan Outer DSCP Classification

• Configuring QoS Policy Maps

  • Configuring DSCP Value on VXLAN Outer Header

• Configuring EAP Profile

  • Configuring EAP Profile

• Configure VXLAN FHS

  • Configure VXLAN FHS

• Configuring OSPFv3

  • Configure OSPFv3 Instance AH Using keychain
  • Configure OSPFv3 Area AH Using keychain
  • Configure OSPFv3 Virtual Link AH Using keychain
  • Configure OSPFv3 Interface AH Using keychain
  • Configure OSPFv3 Instance ESP Using keychain
  • Configure OSPFv3 Area ESP Using keychain
  • Configure OSPFv3 Virtual Link ESP Using keychain
  • Configure OSPFv3 Interface ESP Using keychain

• Configuring OSPFv3

  • Configuring Multicast Telemetry notification for IGMP

• Querying Configurations (Show Commands)

  • Querying the Current MOTD Banner Message

• IS-IS Operational Commands

  • Querying IS-IS Running Configuration

Release 10.3(2)F

• Configuring EIGRP in Interface Configuration Mode
  • Configuring EIGRP Bandwidth
  • Configuring EIGRP mtu(max packet size used by EIGRP)
  • Configuring EIGRP BFD
  • Configuring EIGRP passive-interface
  • Configuring EIGRP next hop self on interface
  • Configuring EIGRP split horizon
  • Configuring EIGRP Authentication Mode
  • Configuring EIGRP Authentication Key Chain
  • Configuring EIGRP Route Control Policy(distributive-list)
  • Configuring EIGRP Route metric Alteration Policy (offset-list)
  • Configuring EIGRP Route Summarization Policy
• Manageability
  • Configuring GRPC tunnel destination
• Configuring PIM Flooding Mechanism with Source Discovery (PFM-SD)
  • Configuring PFM-SD
  • Configuring PFM-SD Boundary

Release 10.3(1)F

• Configuring EIGRP in Interface Configuration Mode
  • Configuring Interface EIGRP Process
  • Configuring EIGRP Hello interval
  • Configuring EIGRP Hold Interval
  • Configuring EIGRP Bandwidth Percent
  • Configuring EIGRP Interface Admin State
  • Configuring EIGRP Delay

• Configuring Apphosting
  • Enabling Apphosting Feature
  • Disabling Apphosting Feature
  • Configuring Bridge Connections
  • Sharing Management Interfaces
  • Configuring an Application
  • Configuring Docker Run Time Options
  • Managing the Lifecycle of an Application
  • Querying Application States
  • Advanced Apphosting Features
    • Overriding App Resource Configuration
    • Supporting Third-Party Docker Applications
    • Adjusting Application Hosting Disk Size

• Querying Interface and VLAN Counters and Statistics
  • Querying Hardware Debug Counters
  • Querying CPU Tx and Tail Drop Counters
  • Querying SPAN Tx and Tail Drop Counters