Configuring an ICMP-Echo Operation

Configuring the Frequency in Seconds

Configuring the Frequency in Seconds

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "frequency": "597709"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <frequency>597709</frequency>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

ip sla 1
icmp-echo 1.1.1.1
frequency 597709

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

The following table contains information about the slaIcmpEcho properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
frequency	sla:Frequency (scalar:Uint32)	Frequency of an operation - The interval at which the configured destination is tracked by the probe. Frequency in seconds(default value is 60). Minimum frequency value for an IP SLAs HTTP probe operation is 60 seconds but 1 second for other probes.	RANGE: [0 , 604800] DEFAULT: 60

slaProbe Properties

The following table contains information about the slaProbe properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Default Frequency

Configuring the Default Frequency

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "frequency": "60"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <frequency>60</frequency>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
default frequency

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
frequency	sla:Frequency (scalar:Uint32)	Frequency of an operation - The interval at which the configured destination is tracked by the probe. Frequency in seconds(default value is 60). Minimum frequency value for an IP SLAs HTTP probe operation is 60 seconds but 1 second for other probes.	RANGE: [0 , 604800] DEFAULT: 60

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting the Frequency in Seconds

Deleting the Frequency in Seconds

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "frequency": "60"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <frequency>60</frequency>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
no frequency 597709

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
frequency	sla:Frequency (scalar:Uint32)	Frequency of an operation - The interval at which the configured destination is tracked by the probe. Frequency in seconds(default value is 60). Minimum frequency value for an IP SLAs HTTP probe operation is 60 seconds but 1 second for other probes.	RANGE: [0 , 604800] DEFAULT: 60

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Owner of Entry

Configuring the Owner of Entry

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "owner": "SampleString_123"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <owner>SampleString_123</owner>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
owner SampleString_123

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
owner	string:Basic	Owner string of the probe(Max size 127)	A sequence of characters

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Default Owner

Configuring the Default Owner

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "owner": ""
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <owner></owner>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
default owner

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
owner	string:Basic	Owner string of the probe(Max size 127)	A sequence of characters

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting the Owner of Entry

Deleting the Owner of Entry

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "owner": ""
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <owner></owner>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
no owner SampleString_123

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
owner	string:Basic	Owner string of the probe(Max size 127)	A sequence of characters

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Data Size Request

Configuring the Data Size Request

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "reqDataSize": "9373"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <reqDataSize>9373</reqDataSize>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
request-data-size 9373

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
reqDataSize	sla:ReqDataSize (scalar:Uint32)	Sets the protocol data size in the payload of an IP SLAs operation's request packet.	RANGE: [16 , 17512] DEFAULT: 28

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Request Data Size

Configuring the Request Data Size

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "reqDataSize": "28"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <reqDataSize>28</reqDataSize>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
default request-data-size

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
reqDataSize	sla:ReqDataSize (scalar:Uint32)	Sets the protocol data size in the payload of an IP SLAs operation's request packet.	RANGE: [16 , 17512] DEFAULT: 28

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting the Data Size Request

Deleting the Data Size Request

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "reqDataSize": "28"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <reqDataSize>28</reqDataSize>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
no request-data-size 9373

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
reqDataSize	sla:ReqDataSize (scalar:Uint32)	Sets the protocol data size in the payload of an IP SLAs operation's request packet.	RANGE: [16 , 17512] DEFAULT: 28

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring a User-Defined Tag

Configuring a User-Defined Tag

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "tag": "SampleString_123"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <tag>SampleString_123</tag>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
tag SampleString_123

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
tag	string:Basic	User defined tag string (Max Size 127)	A sequence of characters

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Default User-Defined Tag

Configuring the Default User-Defined Tag

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "tag": ""
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <tag></tag>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
default tag

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
tag	string:Basic	User defined tag string (Max Size 127)	A sequence of characters

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting a User-Defined Tag

Deleting a User-Defined Tag

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "tag": ""
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <tag></tag>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
no tag SampleString_123

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
tag	string:Basic	User defined tag string (Max Size 127)	A sequence of characters

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Operation Threshold

Configuring the Operation Threshold

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "threshold": "10734"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <threshold>10734</threshold>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
threshold 10734

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
threshold	sla:Threshold (scalar:Uint32)	Operation threshold - this is an upper limit for the observed RTT for the probe. RTT value of a probe exceeding the configured threshold will be marked with Overthreshold return code.	RANGE: [1 , 60000] DEFAULT: 5000

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Default Threshold

Configuring the Default Threshold

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "threshold": "5000"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <threshold>5000</threshold>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
default threshold

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
threshold	sla:Threshold (scalar:Uint32)	Operation threshold - this is an upper limit for the observed RTT for the probe. RTT value of a probe exceeding the configured threshold will be marked with Overthreshold return code.	RANGE: [1 , 60000] DEFAULT: 5000

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting the Operation Threshold

Deleting the Operation Threshold

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "threshold": "5000"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <threshold>5000</threshold>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
no threshold 10734

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
threshold	sla:Threshold (scalar:Uint32)	Operation threshold - this is an upper limit for the observed RTT for the probe. RTT value of a probe exceeding the configured threshold will be marked with Overthreshold return code.	RANGE: [1 , 60000] DEFAULT: 5000

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Timeout of an Operation

Configuring the Timeout of an Operation

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "timeout": "477429727"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <timeout>477429727</timeout>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
timeout 477429727

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
timeout	sla:Timeout (scalar:Uint32)	Timeout of an operation - this is the maximum wait time for completing the operation. The probe will be marked with Timeout return code.	RANGE: [0 , 604800000] DEFAULT: 5000

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Default Timeout

Configuring the Default Timeout

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "timeout": "5000"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <timeout>5000</timeout>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
default timeout

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
timeout	sla:Timeout (scalar:Uint32)	Timeout of an operation - this is the maximum wait time for completing the operation. The probe will be marked with Timeout return code.	RANGE: [0 , 604800000] DEFAULT: 5000

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting the Timeout of an Operation

Deleting the Timeout of an Operation

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "timeout": "5000"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <timeout>5000</timeout>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
no timeout 477429727

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
timeout	sla:Timeout (scalar:Uint32)	Timeout of an operation - this is the maximum wait time for completing the operation. The probe will be marked with Timeout return code.	RANGE: [0 , 604800000] DEFAULT: 5000

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Type of Service

Configuring the Type of Service

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "ipTos": "130"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <ipTos>130</ipTos>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
tos 130

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
ipTos	scalar:Uint32	TOS if the probe is tracking IPv4 destination and Traffic Class if the probe is tracking IPv6 destination.	RANGE: [0, 4294967295]

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Default Type of Service

Configuring the Default Type of Service

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "ipTos": "0"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <ipTos>0</ipTos>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
default tos

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
ipTos	scalar:Uint32	TOS if the probe is tracking IPv4 destination and Traffic Class if the probe is tracking IPv6 destination.	RANGE: [0, 4294967295]

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting the Type of Service

Deleting the Type of Service

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "ipTos": "0"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <ipTos>0</ipTos>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
no tos 130

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
ipTos	scalar:Uint32	TOS if the probe is tracking IPv4 destination and Traffic Class if the probe is tracking IPv6 destination.	RANGE: [0, 4294967295]

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Traffic Class

Configuring the Traffic Class

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "ipv6TrafficClass": "243"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <ipv6TrafficClass>243</ipv6TrafficClass>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
traffic-class 243

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
ipv6TrafficClass	scalar:Uint32	TOS if the probe is tracking IPv4 destination and Traffic Class if the probe is tracking IPv6 destination.	RANGE: [0, 4294967295]

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Default Traffic Class

Configuring the Default Traffic Class

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "ipv6TrafficClass": "0"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <ipv6TrafficClass>0</ipv6TrafficClass>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
default traffic-class

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
ipv6TrafficClass	scalar:Uint32	TOS if the probe is tracking IPv4 destination and Traffic Class if the probe is tracking IPv6 destination.	RANGE: [0, 4294967295]

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting the Traffic Class

Deleting the Traffic Class

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "ipv6TrafficClass": "0"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <ipv6TrafficClass>0</ipv6TrafficClass>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
no traffic-class 243

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
ipv6TrafficClass	scalar:Uint32	TOS if the probe is tracking IPv4 destination and Traffic Class if the probe is tracking IPv6 destination.	RANGE: [0, 4294967295]

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring IP SLAs for a VPN Routing/Forwarding Instances

Configuring IP SLAs for a VPN Routing/Forwarding Instances

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "vrf": "SampleString_123"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <vrf>SampleString_123</vrf>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
vrf SampleString_123

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
vrf	l3:VrfName (string:Basic)	vrf on which the probe is configured.	A sequence of characters DEFAULT: default

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Default IP SLAs for a VPN Routing/Forwarding instance

Configuring the Default IP SLAs for a VPN Routing/Forwarding instance

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "vrf": "default"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <vrf>default</vrf>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
default vrf

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
vrf	l3:VrfName (string:Basic)	vrf on which the probe is configured.	A sequence of characters DEFAULT: default

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting IP SLAs for a VPN Routing/Forwarding Instances

Deleting IP SLAs for a VPN Routing/Forwarding Instances

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "vrf": "default"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <vrf>default</vrf>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
no vrf SampleString_123

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
vrf	l3:VrfName (string:Basic)	vrf on which the probe is configured.	A sequence of characters DEFAULT: default

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Data Verification

Configuring Data Verification

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "verifyData": "yes"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <verifyData>true</verifyData>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
verify-data

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
verifyData	scalar:Bool	Verify Data for Corruption. When data verification is enabled, each operation response is checked for corruption. Use the verify-data command with caution during normal operations because it generates unnecessary overhead.	SELECTION: true or false

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Default Data Verification

Configuring Default Data Verification

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "verifyData": "no"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <verifyData>false</verifyData>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
default verify-data

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
verifyData	scalar:Bool	Verify Data for Corruption. When data verification is enabled, each operation response is checked for corruption. Use the verify-data command with caution during normal operations because it generates unnecessary overhead.	SELECTION: true or false

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Data Verification

Deleting Data Verification

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "destip": "1.1.1.1",
                  "verifyData": "no"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <destip>1.1.1.1</destip>
              <verifyData>false</verifyData>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
no verify-data

MO	DN
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho
slaProbe	sys/sla/inst/sender/operation-1

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format
verifyData	scalar:Bool	Verify Data for Corruption. When data verification is enabled, each operation response is checked for corruption. Use the verify-data command with caution during normal operations because it generates unnecessary overhead.	SELECTION: true or false

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Max Number of History Buckets to Collect

Configuring the Max Number of History Buckets to Collect

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "bucketsKept": "18",
                  "destip": "1.1.1.1"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <bucketsKept>18</bucketsKept>
              <destip>1.1.1.1</destip>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
history buckets-kept 18

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

MO	DN
slaSender	sys/sla/inst/sender
slaProbe	sys/sla/inst/sender/operation-1
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [1 , 2147483647]

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
bucketsKept	scalar:Uint32	Bucket size value - Maximum number of history buckets to collect	RANGE: [1 , 60] DEFAULT: 15
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting the Max Number of History Buckets to Collect

Deleting the Max Number of History Buckets to Collect

POST http://<mgmt0_IP>/api/mo/sys/sla/inst/sender.json

{
  "slaSender": {
    "children": [
      {
        "slaProbe": {
          "attributes": {
            "id": "1"
          },
          "children": [
            {
              "slaIcmpEcho": {
                "attributes": {
                  "bucketsKept": "15",
                  "destip": "1.1.1.1"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <sla-items>
    <inst-items>
      <sender-items>
        <operation-items>
          <Probe-list>
            <id>1</id>
            <icmpecho-items>
              <bucketsKept>15</bucketsKept>
              <destip>1.1.1.1</destip>
            </icmpecho-items>
          </Probe-list>
        </operation-items>
      </sender-items>
    </inst-items>
  </sla-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

ip sla 1
icmp-echo 1.1.1.1
no history buckets-kept 18

Verifying a DME Configuration

MO	DN
slaSender	sys/sla/inst/sender
slaProbe	sys/sla/inst/sender/operation-1
slaIcmpEcho	sys/sla/inst/sender/operation-1/icmpecho

slaProbe Properties

Property Name	Data Type	Description	Values
id	scalar:Uint32	Operation index which is unique for each probe, all the probe related configs and the statistics are displayed using this index.	RANGE: [1 , 2147483647]

slaIcmpEcho Properties

Property Name	Data Type	Description	Values
bucketsKept	scalar:Uint32	Bucket size value - Maximum number of history buckets to collect	RANGE: [1 , 60] DEFAULT: 15
destip	address:Ip	Destination IP address which is tracked by the probe.This property is not applicable if the configured probe type is HTTP or DNS. Modifying this property is not allowed in case of icmp-echo probe.	Value must match ipv4 or ipv6 known format

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html