Configuring IS-IS in Global Configuration Command Mode

Enabling an IP IS-IS Routing Process

Enabling an IP IS-IS Routing Process

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/2"
                }
              }
            }
          ]
        }
      },
      {
        "isisEntity": {
          "children": [
            {
              "isisInternalIf": {
                "attributes": {
                  "id": "eth1/2",
                  "instance": "tag",
                  "v4enable": "yes"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/2</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
  <isis-items>
    <if-items>
      <InternalIf-list>
        <id>eth1/2</id>
        <instance>tag</instance>
        <v4enable>true</v4enable>
      </InternalIf-list>
    </if-items>
  </isis-items>
</System>

Note: This example was added in Release 9.2(2).


CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

interface ethernet 1/2
 ip router isis tag

Note: The property information for this example was added in Release 9.3(3).


Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

MODN
topSystem sys
interfaceEntity sys/intf
l1PhysIf sys/intf/phys-{[id]}
isisEntity sys/isis
isisInternalIf sys/isis/if-{[id]}


l1PhysIf Properties

The following table contains information about the l1PhysIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property NameData TypeDescriptionValues
idnw:IfId
(base:IfIndex)		An identifier .Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100


isisInternalIf Properties

The following table contains information about the isisInternalIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property NameData TypeDescriptionValues
idnw:IfId
(base:IfIndex)		An identifier .Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
instanceisis:InstanceName
(naming:Name)		Instance to which the interface belongs to
MAX SIZE: 16
v4enablescalar:Bool
Enabling ISIS router tag on Interface's IPV4 familySELECTION: true or false
DEFAULT: no


Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Disabling an IP IS-IS Routing Process

Disabling an IP IS-IS Routing Process

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/2"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/2</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
</System>

Note: This example was added in Release 9.2(2).


CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

interface ethernet 1/2
 no ip router isis tag

Note: The property information for this example was added in Release 9.3(3).


Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

MODN
topSystem sys
interfaceEntity sys/intf
l1PhysIf sys/intf/phys-{[id]}


l1PhysIf Properties

The following table contains information about the l1PhysIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property NameData TypeDescriptionValues
idnw:IfId
(base:IfIndex)		An identifier .Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100


Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Enabling an IPv6 IS-IS Routing Process

Enabling an IPv6 IS-IS Routing Process

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/2"
                }
              }
            }
          ]
        }
      },
      {
        "isisEntity": {
          "children": [
            {
              "isisInternalIf": {
                "attributes": {
                  "id": "eth1/2",
                  "instance": "tag",
                  "v6enable": "yes"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/2</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
  <isis-items>
    <if-items>
      <InternalIf-list>
        <id>eth1/2</id>
        <instance>tag</instance>
        <v6enable>true</v6enable>
      </InternalIf-list>
    </if-items>
  </isis-items>
</System>

Note: This example was added in Release 9.2(2).


CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

interface ethernet 1/2
 ipv6 router isis tag

Note: The property information for this example was added in Release 9.3(3).


Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

MODN
topSystem sys
interfaceEntity sys/intf
l1PhysIf sys/intf/phys-{[id]}
isisEntity sys/isis
isisInternalIf sys/isis/if-{[id]}


l1PhysIf Properties

The following table contains information about the l1PhysIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property NameData TypeDescriptionValues
idnw:IfId
(base:IfIndex)		An identifier .Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100


isisInternalIf Properties

The following table contains information about the isisInternalIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property NameData TypeDescriptionValues
idnw:IfId
(base:IfIndex)		An identifier .Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
instanceisis:InstanceName
(naming:Name)		Instance to which the interface belongs to
MAX SIZE: 16
v6enablescalar:Bool
Enabling ISIS router tag on Interface's IPV6 familySELECTION: true or false
DEFAULT: no


Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Disabling an IPv6 IS-IS Routing Process

Disabling an IPv6 IS-IS Routing Process

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/2"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/2</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
</System>

Note: This example was added in Release 9.2(2).


CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

interface ethernet 1/2
 no ipv6 router isis tag

Note: The property information for this example was added in Release 9.3(3).


Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

MODN
topSystem sys
interfaceEntity sys/intf
l1PhysIf sys/intf/phys-{[id]}


l1PhysIf Properties

The following table contains information about the l1PhysIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property NameData TypeDescriptionValues
idnw:IfId
(base:IfIndex)		An identifier .Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100


Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html