Configuring MPLS LDP on an Interface

Configuring IP over MPLS

Configuring IP over MPLS

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/2"
                }
              }
            }
          ]
        }
      },
      {
        "mplsldpLDP": {
          "attributes": {
            "adminSt": "enabled"
          },
          "children": [
            {
              "mplsldpIf": {
                "attributes": {
                  "id": "eth1/2",
                  "mplsIp": "yes"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/2</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
  <ldp-items>
    <adminSt>enabled</adminSt>
    <if-items>
      <If-list>
        <id>eth1/2</id>
        <mplsIp>true</mplsIp>
      </If-list>
    </if-items>
  </ldp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

mpls ldp configuration
interface ethernet 1/2
mpls ip

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

MO	DN
topSystem	sys
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/2]
mplsldpLDP	sys/ldp
mplsldpIf	sys/ldp/if-[eth1/2]

l1PhysIf Properties

The following table contains information about the l1PhysIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

mplsldpLDP Properties

The following table contains information about the mplsldpLDP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
adminSt	nw:AdminSt (scalar:Enum8)	The administrative state of the object or policy.	SELECTION: 1 - enabled 2 - disabled DEFAULT: enabled

mplsldpIf Properties

The following table contains information about the mplsldpIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
mplsIp	scalar:Bool	The mplsIp property enables MPLS LDP on the specified interface	SELECTION: true or false DEFAULT: false

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting IP over MPLS

Deleting IP over MPLS

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/2"
                }
              }
            }
          ]
        }
      },
      {
        "mplsldpLDP": {
          "attributes": {
            "adminSt": "enabled"
          },
          "children": [
            {
              "mplsldpIf": {
                "attributes": {
                  "id": "eth1/2",
                  "mplsIp": "no"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/2</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
  <ldp-items>
    <adminSt>enabled</adminSt>
    <if-items>
      <If-list>
        <id>eth1/2</id>
        <mplsIp>false</mplsIp>
      </If-list>
    </if-items>
  </ldp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

mpls ldp configuration
interface ethernet 1/2
no mpls ip

Verifying a DME Configuration

MO	DN
topSystem	sys
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/2]
mplsldpLDP	sys/ldp
mplsldpIf	sys/ldp/if-[eth1/2]

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

mplsldpLDP Properties

Property Name	Data Type	Description	Values
adminSt	nw:AdminSt (scalar:Enum8)	The administrative state of the object or policy.	SELECTION: 1 - enabled 2 - disabled DEFAULT: enabled

mplsldpIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
mplsIp	scalar:Bool	The mplsIp property enables MPLS LDP on the specified interface	SELECTION: true or false DEFAULT: false

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring LDP-IGP Synchronization on an Interface

Configuring LDP-IGP Synchronization on an Interface

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/2"
                }
              }
            }
          ]
        }
      },
      {
        "mplsldpLDP": {
          "attributes": {
            "adminSt": "enabled"
          },
          "children": [
            {
              "mplsldpIf": {
                "attributes": {
                  "delayTime": "0",
                  "id": "eth1/2",
                  "igpSync": "yes"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/2</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
  <ldp-items>
    <adminSt>enabled</adminSt>
    <if-items>
      <If-list>
        <id>eth1/2</id>
        <delayTime>0</delayTime>
        <igpSync>true</igpSync>
      </If-list>
    </if-items>
  </ldp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

mpls ldp configuration
interface ethernet 1/2
mpls ldp igp sync

Verifying a DME Configuration

MO	DN
topSystem	sys
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/2]
mplsldpLDP	sys/ldp
mplsldpIf	sys/ldp/if-[eth1/2]

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

mplsldpLDP Properties

Property Name	Data Type	Description	Values
adminSt	nw:AdminSt (scalar:Enum8)	The administrative state of the object or policy.	SELECTION: 1 - enabled 2 - disabled DEFAULT: enabled

mplsldpIf Properties

Property Name	Data Type	Description	Values
delayTime	mplsldp:DelayTime (scalar:Uint16)	Configures a delay time for MPLS LDP IGP synchronization on the specified interface.	RANGE: [0 , 60] DEFAULT: 0
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
igpSync	scalar:Bool	Enables MPLS LDP interior gateway protocol sync	SELECTION: true or false DEFAULT: true

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting LDP-IGP Synchronization on an Interface

Deleting LDP-IGP Synchronization on an Interface

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/2"
                }
              }
            }
          ]
        }
      },
      {
        "mplsldpLDP": {
          "attributes": {
            "adminSt": "enabled"
          },
          "children": [
            {
              "mplsldpIf": {
                "attributes": {
                  "delayTime": "0",
                  "id": "eth1/2",
                  "igpSync": "no"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/2</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
  <ldp-items>
    <adminSt>enabled</adminSt>
    <if-items>
      <If-list>
        <id>eth1/2</id>
        <delayTime>0</delayTime>
        <igpSync>false</igpSync>
      </If-list>
    </if-items>
  </ldp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

mpls ldp configuration
interface ethernet 1/2
no mpls ldp igp sync

Verifying a DME Configuration

MO	DN
topSystem	sys
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/2]
mplsldpLDP	sys/ldp
mplsldpIf	sys/ldp/if-[eth1/2]

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

mplsldpLDP Properties

Property Name	Data Type	Description	Values
adminSt	nw:AdminSt (scalar:Enum8)	The administrative state of the object or policy.	SELECTION: 1 - enabled 2 - disabled DEFAULT: enabled

mplsldpIf Properties

Property Name	Data Type	Description	Values
delayTime	mplsldp:DelayTime (scalar:Uint16)	Configures a delay time for MPLS LDP IGP synchronization on the specified interface.	RANGE: [0 , 60] DEFAULT: 0
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
igpSync	scalar:Bool	Enables MPLS LDP interior gateway protocol sync	SELECTION: true or false DEFAULT: true

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring a Delay Time for LDP IGP Synchronization on the Specified Interface

Configuring a Delay Time for LDP IGP Synchronization on the Specified Interface

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/2"
                }
              }
            }
          ]
        }
      },
      {
        "mplsldpLDP": {
          "attributes": {
            "adminSt": "enabled"
          },
          "children": [
            {
              "mplsldpIf": {
                "attributes": {
                  "delayTime": "30",
                  "id": "eth1/2",
                  "igpSync": "yes"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/2</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
  <ldp-items>
    <adminSt>enabled</adminSt>
    <if-items>
      <If-list>
        <id>eth1/2</id>
        <delayTime>30</delayTime>
        <igpSync>true</igpSync>
      </If-list>
    </if-items>
  </ldp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

mpls ldp configuration
interface ethernet 1/2
mpls ldp igp sync delay 30

Verifying a DME Configuration

MO	DN
topSystem	sys
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/2]
mplsldpLDP	sys/ldp
mplsldpIf	sys/ldp/if-[eth1/2]

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

mplsldpLDP Properties

Property Name	Data Type	Description	Values
adminSt	nw:AdminSt (scalar:Enum8)	The administrative state of the object or policy.	SELECTION: 1 - enabled 2 - disabled DEFAULT: enabled

mplsldpIf Properties

Property Name	Data Type	Description	Values
delayTime	mplsldp:DelayTime (scalar:Uint16)	Configures a delay time for MPLS LDP IGP synchronization on the specified interface.	RANGE: [0 , 60] DEFAULT: 0
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
igpSync	scalar:Bool	Enables MPLS LDP interior gateway protocol sync	SELECTION: true or false DEFAULT: true

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting a Delay Time for LDP IGP Synchronization on the Specified Interface

Deleting a Delay Time for LDP IGP Synchronization on the Specified Interface

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/2"
                }
              }
            }
          ]
        }
      },
      {
        "mplsldpLDP": {
          "attributes": {
            "adminSt": "enabled"
          },
          "children": [
            {
              "mplsldpIf": {
                "attributes": {
                  "delayTime": "0",
                  "id": "eth1/2",
                  "igpSync": "no"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/2</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
  <ldp-items>
    <adminSt>enabled</adminSt>
    <if-items>
      <If-list>
        <id>eth1/2</id>
        <delayTime>0</delayTime>
        <igpSync>false</igpSync>
      </If-list>
    </if-items>
  </ldp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

mpls ldp configuration
interface ethernet 1/2
no mpls ldp igp sync delay 30

Verifying a DME Configuration

MO	DN
topSystem	sys
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/2]
mplsldpLDP	sys/ldp
mplsldpIf	sys/ldp/if-[eth1/2]

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

mplsldpLDP Properties

Property Name	Data Type	Description	Values
adminSt	nw:AdminSt (scalar:Enum8)	The administrative state of the object or policy.	SELECTION: 1 - enabled 2 - disabled DEFAULT: enabled

mplsldpIf Properties

Property Name	Data Type	Description	Values
delayTime	mplsldp:DelayTime (scalar:Uint16)	Configures a delay time for MPLS LDP IGP synchronization on the specified interface.	RANGE: [0 , 60] DEFAULT: 0
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
igpSync	scalar:Bool	Enables MPLS LDP interior gateway protocol sync	SELECTION: true or false DEFAULT: true

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring MPLS LDP Autoconfiguration for IGP Interfaces

Configuring MPLS LDP Autoconfiguration for IGP Interfaces

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/2"
                }
              }
            }
          ]
        }
      },
      {
        "mplsldpLDP": {
          "attributes": {
            "adminSt": "enabled"
          },
          "children": [
            {
              "mplsldpIf": {
                "attributes": {
                  "id": "eth1/2",
                  "igpAuto": "yes"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/2</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
  <ldp-items>
    <adminSt>enabled</adminSt>
    <if-items>
      <If-list>
        <id>eth1/2</id>
        <igpAuto>true</igpAuto>
      </If-list>
    </if-items>
  </ldp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

mpls ldp configuration
interface ethernet 1/2
mpls ldp igp autoconfig

Verifying a DME Configuration

MO	DN
topSystem	sys
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/2]
mplsldpLDP	sys/ldp
mplsldpIf	sys/ldp/if-[eth1/2]

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

mplsldpLDP Properties

Property Name	Data Type	Description	Values
adminSt	nw:AdminSt (scalar:Enum8)	The administrative state of the object or policy.	SELECTION: 1 - enabled 2 - disabled DEFAULT: enabled

mplsldpIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
igpAuto	scalar:Bool	Enables MPLS LDP interior gateway protocol autoconfig	SELECTION: true or false DEFAULT: true

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting MPLS LDP Autoconfiguration for IGP Interfaces

Deleting MPLS LDP Autoconfiguration for IGP Interfaces

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/2"
                }
              }
            }
          ]
        }
      },
      {
        "mplsldpLDP": {
          "attributes": {
            "adminSt": "enabled"
          },
          "children": [
            {
              "mplsldpIf": {
                "attributes": {
                  "id": "eth1/2",
                  "igpAuto": "no"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/2</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
  <ldp-items>
    <adminSt>enabled</adminSt>
    <if-items>
      <If-list>
        <id>eth1/2</id>
        <igpAuto>false</igpAuto>
      </If-list>
    </if-items>
  </ldp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

mpls ldp configuration
interface ethernet 1/2
no mpls ldp igp autoconfig

Verifying a DME Configuration

MO	DN
topSystem	sys
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/2]
mplsldpLDP	sys/ldp
mplsldpIf	sys/ldp/if-[eth1/2]

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

mplsldpLDP Properties

Property Name	Data Type	Description	Values
adminSt	nw:AdminSt (scalar:Enum8)	The administrative state of the object or policy.	SELECTION: 1 - enabled 2 - disabled DEFAULT: enabled

mplsldpIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
igpAuto	scalar:Bool	Enables MPLS LDP interior gateway protocol autoconfig	SELECTION: true or false DEFAULT: true

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring an IP Address to use for LDP Transport Address

Configuring an IP Address to use for LDP Transport Address

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/2"
                }
              }
            }
          ]
        }
      },
      {
        "mplsldpLDP": {
          "attributes": {
            "adminSt": "enabled"
          },
          "children": [
            {
              "mplsldpIf": {
                "attributes": {
                  "discTrnspIntf": "yes",
                  "discTrnspIp": "0.0.0.0",
                  "id": "eth1/2"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/2</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
  <ldp-items>
    <adminSt>enabled</adminSt>
    <if-items>
      <If-list>
        <id>eth1/2</id>
        <discTrnspIntf>true</discTrnspIntf>
        <discTrnspIp>0.0.0.0</discTrnspIp>
      </If-list>
    </if-items>
  </ldp-items>
</System>

conf tconf t

Note: This example was added in Release 9.3(3).

CLI Commands

mpls ldp configuration
interface ethernet 1/2
mpls ldp discovery transport-address interface

Verifying a DME Configuration

MO	DN
topSystem	sys
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/2]
mplsldpLDP	sys/ldp
mplsldpIf	sys/ldp/if-[eth1/2]

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

mplsldpLDP Properties

Property Name	Data Type	Description	Values
adminSt	nw:AdminSt (scalar:Enum8)	The administrative state of the object or policy.	SELECTION: 1 - enabled 2 - disabled DEFAULT: enabled

mplsldpIf Properties

Property Name	Data Type	Description	Values
discTrnspIntf	scalar:Bool	Use interface address for LDP transport address	SELECTION: true or false DEFAULT: false
discTrnspIp	address:Ip	IP address to use for LDP transport address	Value must match ipv4 or ipv6 known format
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting an IP Address to use for LDP Transport Address

Deleting an IP Address to use for LDP Transport Address

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/2"
                }
              }
            }
          ]
        }
      },
      {
        "mplsldpLDP": {
          "attributes": {
            "adminSt": "enabled"
          },
          "children": [
            {
              "mplsldpIf": {
                "attributes": {
                  "discTrnspIntf": "no",
                  "discTrnspIp": "0.0.0.0",
                  "id": "eth1/2"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/2</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
  <ldp-items>
    <adminSt>enabled</adminSt>
    <if-items>
      <If-list>
        <id>eth1/2</id>
        <discTrnspIntf>false</discTrnspIntf>
        <discTrnspIp>0.0.0.0</discTrnspIp>
      </If-list>
    </if-items>
  </ldp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

mpls ldp configuration
interface ethernet 1/2
no mpls ldp discovery transport-address interface

Verifying a DME Configuration

MO	DN
topSystem	sys
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/2]
mplsldpLDP	sys/ldp
mplsldpIf	sys/ldp/if-[eth1/2]

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

mplsldpLDP Properties

Property Name	Data Type	Description	Values
adminSt	nw:AdminSt (scalar:Enum8)	The administrative state of the object or policy.	SELECTION: 1 - enabled 2 - disabled DEFAULT: enabled

mplsldpIf Properties

Property Name	Data Type	Description	Values
discTrnspIntf	scalar:Bool	Use interface address for LDP transport address	SELECTION: true or false DEFAULT: false
discTrnspIp	address:Ip	IP address to use for LDP transport address	Value must match ipv4 or ipv6 known format
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring an Interface LDP Transort Address

Configuring an Interface LDP Transort Address

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/2"
                }
              }
            }
          ]
        }
      },
      {
        "mplsldpLDP": {
          "attributes": {
            "adminSt": "enabled"
          },
          "children": [
            {
              "mplsldpIf": {
                "attributes": {
                  "discTrnspIntf": "no",
                  "discTrnspIp": "1.2.3.4",
                  "id": "eth1/2"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/2</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
  <ldp-items>
    <adminSt>enabled</adminSt>
    <if-items>
      <If-list>
        <id>eth1/2</id>
        <discTrnspIntf>false</discTrnspIntf>
        <discTrnspIp>1.2.3.4</discTrnspIp>
      </If-list>
    </if-items>
  </ldp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

mpls ldp configuration
interface ethernet 1/2
mpls ldp discovery transport-address 1.2.3.4

Verifying a DME Configuration

MO	DN
topSystem	sys
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/2]
mplsldpLDP	sys/ldp
mplsldpIf	sys/ldp/if-[eth1/2]

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

mplsldpLDP Properties

Property Name	Data Type	Description	Values
adminSt	nw:AdminSt (scalar:Enum8)	The administrative state of the object or policy.	SELECTION: 1 - enabled 2 - disabled DEFAULT: enabled

mplsldpIf Properties

Property Name	Data Type	Description	Values
discTrnspIntf	scalar:Bool	Use interface address for LDP transport address	SELECTION: true or false DEFAULT: false
discTrnspIp	address:Ip	IP address to use for LDP transport address	Value must match ipv4 or ipv6 known format
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting an Interface LDP Transort Address

Deleting an Interface LDP Transort Address

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/2"
                }
              }
            }
          ]
        }
      },
      {
        "mplsldpLDP": {
          "attributes": {
            "adminSt": "enabled"
          },
          "children": [
            {
              "mplsldpIf": {
                "attributes": {
                  "discTrnspIntf": "no",
                  "discTrnspIp": "0.0.0.0",
                  "id": "eth1/2"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/2</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
  <ldp-items>
    <adminSt>enabled</adminSt>
    <if-items>
      <If-list>
        <id>eth1/2</id>
        <discTrnspIntf>false</discTrnspIntf>
        <discTrnspIp>0.0.0.0</discTrnspIp>
      </If-list>
    </if-items>
  </ldp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

mpls ldp configuration
interface ethernet 1/2
no mpls ldp discovery transport-address 1.2.3.4

Verifying a DME Configuration

MO	DN
topSystem	sys
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/2]
mplsldpLDP	sys/ldp
mplsldpIf	sys/ldp/if-[eth1/2]

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

mplsldpLDP Properties

Property Name	Data Type	Description	Values
adminSt	nw:AdminSt (scalar:Enum8)	The administrative state of the object or policy.	SELECTION: 1 - enabled 2 - disabled DEFAULT: enabled

mplsldpIf Properties

Property Name	Data Type	Description	Values
discTrnspIntf	scalar:Bool	Use interface address for LDP transport address	SELECTION: true or false DEFAULT: false
discTrnspIp	address:Ip	IP address to use for LDP transport address	Value must match ipv4 or ipv6 known format
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html