Configuring OSPFv3

OSPFv3 is an IETF link-state protocol. An OSPFv3 router sends a special message, called a hello packet, out each OSPF-enabled interface to discover other OSPFv3 neighbor routers. Once a neighbor is discovered, the two routers compare information in the Hello packet to determine if the routers have compatible configurations. The neighbor routers attempt to establish adjacency, which means that the routers synchronize their link-state databases to ensure that they have identical OSPFv3 routing information. Adjacent routers share link-state advertisements (LSAs) that include information about the operational state of each link, the cost of the link, and any other neighbor information. The routers then flood these received LSAs out every OSPF-enabled interface so that all OSPFv3 routers eventually have identical link-state databases. When all OSPFv3 routers have identical link-state databases, the network is converged. Each router then uses Dijkstra’s Shortest Path First (SPF) algorithm to build its route table.

Enabling OSPFv3

Enabling OSPFv3

POST http://<mgmt0_IP>/api/mo/sys/fm.json

{
  "fmEntity": {
    "children": [
      {
        "fmOspfv3": {
          "attributes": {
            "adminSt": "enabled"
}}}]}}

{
    imdata:[]
}

<System>
  <fm-items>
    <ospfv3-items>
      <adminSt>enabled</adminSt>
    </ospfv3-items>
  </fm-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

feature ospfv3

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

MO	DN
fmEntity	sys/fm
fmOspfv3	sys/fm/ospfv3

fmOspfv3 Properties

The following table contains information about the fmOspfv3 properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
adminSt	fm:AdminState (scalar:Enum8)	Admin status	SELECTION: 1 - enabled 2 - disabled DEFAULT: disabled

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Disabling OSPFv3

Disabling OSPFv3

POST http://<mgmt0_IP>/api/mo/sys/fm.json

{
  "fmEntity": {
    "children": [
      {
        "fmOspfv3": {
          "attributes": {
            "adminSt": "disabled"
}}}]}}

{
    imdata:[]
}

<System>
  <fm-items>
    <ospfv3-items>
      <adminSt>disabled</adminSt>
    </ospfv3-items>
  </fm-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

no feature ospfv3

Verifying a DME Configuration

MO	DN
fmEntity	sys/fm
fmOspfv3	sys/fm/ospfv3

fmOspfv3 Properties

Property Name	Data Type	Description	Values
adminSt	fm:AdminState (scalar:Enum8)	Admin status	SELECTION: 1 - enabled 2 - disabled DEFAULT: disabled

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Enabling Internet Messaging Program (IMP)

Enabling Internet Messaging Program (IMP)

POST http://<mgmt0_IP>/api/mo/sys/fm.json

{
  "fmEntity": {
    "children": [
      {
        "fmImp": {
          "attributes": {
            "adminSt": "enabled"
}}}]}}

{
    imdata:[]
}

<System>
  <fm-items>
    <imp-items>
      <adminSt>enabled</adminSt>
    </imp-items>
  </fm-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

feature imp

Verifying a DME Configuration

MO	DN
fmEntity	sys/fm
fmImp	sys/fm/imp

fmImp Properties

The following table contains information about the fmImp properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
adminSt	fm:AdminState (scalar:Enum8)	Admin status	SELECTION: 1 - enabled 2 - disabled DEFAULT: disabled

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Disabling Internet Messaging Program (IMP)

Disabling IMP Internet Messaging Program (IMP)

POST http://<mgmt0_IP>/api/mo/sys/fm.json

{
  "fmEntity": {
    "children": [
      {
        "fmImp": {
          "attributes": {
            "adminSt": "disabled"
}}}]}}

{
    imdata:[]
}

<System>
  <fm-items>
    <imp-items>
      <adminSt>disabled</adminSt>
    </imp-items>
  </fm-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

no feature imp

Verifying a DME Configuration

MO	DN
fmEntity	sys/fm
fmImp	sys/fm/imp

fmImp Properties

Property Name	Data Type	Description	Values
adminSt	fm:AdminState (scalar:Enum8)	Admin status	SELECTION: 1 - enabled 2 - disabled DEFAULT: disabled

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring a Routing Process

Configuring a Routing Process

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

router ospfv3 Test_1

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

MO	DN
ospfv3Dom	sys/ospfv3/inst-default/dom-default
ospfv3Inst	sys/ospfv3/inst-default

ospfv3Dom Properties

The following table contains information about the ospfv3Dom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
name	naming:Name256 string:Basic	The name of the object.

ospfv3Inst Properties

The following table contains information about the ospfv3Inst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
name	naming:Name256 string:Basic	The name of the object.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting a Routing Process

Deleting a Routing Process

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
           "name": "Test_1",
            "status": "deleted"
}}}]}}

{
    imdata:[]
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list nc:operation="delete">
        <name>Test_1</name>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(1).

CLI Commands

no router ospfv3 Test_1

MO	DN
ospfv3Inst	sys/ospfv3/inst-Test_1

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 string:Basic	The name of the object.
status	mo:ModificationStatus (scalar:Bitmask32)	Modification status	SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Flush Routes under ospfv3

Configuring Flush Routes under ospfv3

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "flushRoutes": "yes",
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <flushRoutes>true</flushRoutes>
        <dom-items>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

router ospfv3 Test_1
flush-routes

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
flushRoutes	scalar:Bool	Flush routes on non-graceful controlled restart	SELECTION: true or false DEFAULT: false
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Flush Routes Under OSPFv3

Deleting Flush Routes Under OSPFv3

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "flushRoutes": "no",
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <flushRoutes>false</flushRoutes>
        <dom-items>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

router ospfv3 Test_1
no flush-routes

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
flushRoutes	scalar:Bool	Flush routes on non-graceful controlled restart	SELECTION: true or false DEFAULT: false
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Enabling Graceful Restart Planned Only

 Enabling Graceful Restart Planned Only

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3Gr": {
                      "attributes": {
                        "ctrl": "planned-only"
}}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <gr-items>
              <ctrl>planned-only</ctrl>
            </gr-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

router ospfv3 Test_1
graceful-restart planned-only

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3Gr	sys/ospfv3/inst-Test_1/dom-default/gr

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Gr Properties

The following table contains information about the ospfv3Gr properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
ctrl	ospfv3:GrCtrl (scalar:Enum8)	Graceful restart controls like planned, complete and disabled state	SELECTION: 1 - planned-only 2 - complete 3 - disabled DEFAULT: complete

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Disabling Graceful Restart

Disabling Graceful Restart

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3Gr": {
                      "attributes": {
                        "ctrl": "disabled"
}}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <gr-items>
              <ctrl>disabled</ctrl>
            </gr-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

router ospfv3 Test_1
no graceful-restart planned-only

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3Gr	sys/ospfv3/inst-Test_1/dom-default/gr

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Gr Properties

Property Name	Data Type	Description	Values
ctrl	ospfv3:GrCtrl (scalar:Enum8)	Graceful restart controls like planned, complete and disabled state	SELECTION: 1 - planned-only 2 - complete 3 - disabled DEFAULT: complete

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configure Maximum Interval to Restart Gracefully

Configure Maximum Interval to Restart Gracefully

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3Gr": {
                      "attributes": {
                        "gracePeriod": "699"
}}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <gr-items>
              <gracePeriod>699</gracePeriod>
            </gr-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

router ospfv3 Test_1
graceful-restart grace-period 699

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3Gr	sys/ospfv3/inst-Test_1/dom-default/gr

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Gr Properties

Property Name	Data Type	Description	Values
gracePeriod	ospfv3:GrPeriod (scalar:Uint32)	Graceful restart period in seconds starting from 5 to 1800	RANGE: [5 , 1800] DEFAULT: 60

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Maximum Interval to Restart Gracefully

Deleting Maximum Interval to Restart Gracefully

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3Gr": {
                      "attributes": {
                        "gracePeriod": "60"
}}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <gr-items>
              <gracePeriod>60</gracePeriod>
            </gr-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

router ospfv3 Test_1
no graceful-restart grace-period 699

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3Gr	sys/ospfv3/inst-Test_1/dom-default/gr

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Gr Properties

Property Name	Data Type	Description	Values
gracePeriod	ospfv3:GrPeriod (scalar:Uint32)	Graceful restart period in seconds starting from 5 to 1800	RANGE: [5 , 1800] DEFAULT: 60

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Helper-Disable

Configuring Helper-Disable

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3Gr": {
                      "attributes": {
                        "helper": "no"
}}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <gr-items>
              <helper>false</helper>
            </gr-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

router ospfv3 Test_1
graceful-restart helper-disable

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3Gr	sys/ospfv3/inst-Test_1/dom-default/gr

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Gr Properties

Property Name	Data Type	Description	Values
helper	scalar:Bool	Graceful restart helper mode	SELECTION: true or false DEFAULT: true

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Unconfiguring Helper-Disable

Unconfiguring Helper-Disable

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3Gr": {
                      "attributes": {
                        "helper": "yes"
}}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <gr-items>
              <helper>true</helper>
            </gr-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

router ospfv3 Test_1
no graceful-restart helper-disable

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3Gr	sys/ospfv3/inst-Test_1/dom-default/gr

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Gr Properties

Property Name	Data Type	Description	Values
helper	scalar:Bool	Graceful restart helper mode	SELECTION: true or false DEFAULT: true

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring OSPFv3 Router Isolation from the OSPFv3 Perspective

Configuring OSPFv3 Router Isolation from the OSPFv3 Perspective

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "isolate": "yes",
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <isolate>true</isolate>
        <dom-items>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

router ospfv3 Test_1
isolate

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
isolate	scalar:Bool	Isolate this router from OSPFv3 perspective	SELECTION: true or false DEFAULT: false
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Unconfiguring OSPFv3 Router Isolation from the OSPFv3 Perspective

Unconfiguring OSPFv3 Router Isolation from the OSPFv3 Perspective

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "isolate": "no",
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <isolate>false</isolate>
        <dom-items>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

router ospfv3 Test_1
no isolate

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
isolate	scalar:Bool	Isolate this router from OSPFv3 perspective	SELECTION: true or false DEFAULT: false
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Enable name-lookup for OSPFv3

Enable name-lookup for OSPFv3

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default",
                  "nameLookup": "yes"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <nameLookup>true</nameLookup>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

router ospfv3 Test_1
name-lookup

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63
nameLookup	scalar:Bool	Enable Name Lookup for OSPFv3 Neighbors	SELECTION: true or false DEFAULT: false

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Disable name-lookup for OSPFv3

Router Ids as DNS Names

Disable name-lookup for OSPFv3

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default",
                  "nameLookup": "no"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <nameLookup>false</nameLookup>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

router ospfv3 Test_1
no name-lookup

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63
nameLookup	scalar:Bool	Enable Name Lookup for OSPFv3 Neighbors	SELECTION: true or false DEFAULT: false

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Suppressing Routing Updates on the Interface (Interfaces Passive by Default)

Suppressing Routing Updates on the Interface (Interfaces Passive by Default)

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default",
                  "passiveIntfDefault": "yes"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <passiveIntfDefault>true</passiveIntfDefault>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

router ospfv3 Test_1
passive-interface default

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63
passiveIntfDefault	scalar:Bool	Suppress routing updates on the interface	SELECTION: true or false DEFAULT: false

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Unsuppressing Routing Updates on the Interface(Interfaces non-passive by Default)

Unsuppressing Routing Updates on the Interface(Interfaces non-passive by Default)

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default",
                  "passiveIntfDefault": "no"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <passiveIntfDefault>false</passiveIntfDefault>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

router ospfv3 Test_1
no passive-interface default

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63
passiveIntfDefault	scalar:Bool	Suppress routing updates on the interface	SELECTION: true or false DEFAULT: false

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Shutting down ospfv3 instance

shutting down ospfv3 instance

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "adminSt": "disabled",
                  "name": "default"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <adminSt>disabled</adminSt>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

router ospfv3 Test_1
shutdown

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
adminSt	nw:AdminSt (scalar:Enum8)	OSPFv3 VRF administrative state	SELECTION: 1 - enabled 2 - disabled DEFAULT: enabled
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Unconfiguring shutdown of ospfv3 protocol instance

Unconfiguring the OSPFv3 Protocol Instance Shutdown

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "adminSt": "enabled",
                  "name": "default"
}}}]}}]}}

{
    imdata:[]
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <adminSt>enabled</adminSt>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

router ospfv3 Test_1
no shutdown

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
adminSt	nw:AdminSt (scalar:Enum8)	OSPFv3 VRF administrative state	SELECTION: 1 - enabled 2 - disabled DEFAULT: enabled
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Area NSSA with a Route Map Filter Name

Configuring the Area NSSA with a Route Map Filter Name

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3Area": {
                      "attributes": {
                        "id": "1.2.3.4",
                        "redistribute": "no",
                        "summary": "no",
                        "supressFa": "no",
                        "type": "nssa"
                      },
                      "children": [
                        {
                          "ospfv3DefRtLeakP": {
                            "attributes": {
                              "rtMap": "SampleString_123"
}}}]}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>1.2.3.4</id>
                <redistribute>false</redistribute>
                <summary>false</summary>
                <supressFa>false</supressFa>
                <type>nssa</type>
                <defrtleak-items>
                  <rtMap>SampleString_123</rtMap>
                </defrtleak-items>
              </Area-list>
            </area-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
area 1.2.3.4 nssa no-summary no-redistribution default-information-originate route-map SampleString_123

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3Area	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4
ospfv3DefRtLeakP	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4/defrtleak

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

The following table contains information about the ospfv3Area properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters
redistribute	scalar:Bool	Send redistributed LSAs into NSSA area	SELECTION: true or false DEFAULT: true
summary	scalar:Bool	Originate summary LSA into other areas	SELECTION: true or false DEFAULT: true
supressFa	scalar:Bool	Supress forwarding address in translated LSA	SELECTION: true or false DEFAULT: false
type	ospfv3:AreaT (scalar:Enum8)	Configure area type as NSSA or stub	SELECTION: 1 - regular 2 - stub 3 - nssa DEFAULT: regular

ospfv3DefRtLeakP Properties

The following table contains information about the ospfv3DefRtLeakP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
rtMap	string:Basic	The name of the default route leak policy route map. This route map name is used to control distribution.	A sequence of characters

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting the Area NSSA with a Route Map Filter Name

Deleting the Area NSSA with a Route Map Filter Name

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3Area": {
                      "attributes": {
                        "id": "1.2.3.4",
                        "redistribute": "yes",
                        "summary": "yes",
                        "supressFa": "no",
                        "type": "nssa"
                      },
                      "children": [
                        {
                          "ospfv3DefRtLeakP": {
                            "attributes": {
                              "rtMap": "SampleString_123"
}}}]}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>1.2.3.4</id>
                <redistribute>true</redistribute>
                <summary>true</summary>
                <supressFa>false</supressFa>
                <type>nssa</type>
                <defrtleak-items>
                  <rtMap>SampleString_123</rtMap>
                </defrtleak-items>
              </Area-list>
            </area-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
no area 1.2.3.4 nssa no-summary no-redistribution default-information-originate route-map SampleString_123

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3Area	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4
ospfv3DefRtLeakP	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4/defrtleak

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters
redistribute	scalar:Bool	Send redistributed LSAs into NSSA area	SELECTION: true or false DEFAULT: true
summary	scalar:Bool	Originate summary LSA into other areas	SELECTION: true or false DEFAULT: true
supressFa	scalar:Bool	Supress forwarding address in translated LSA	SELECTION: true or false DEFAULT: false
type	ospfv3:AreaT (scalar:Enum8)	Configure area type as NSSA or stub	SELECTION: 1 - regular 2 - stub 3 - nssa DEFAULT: regular

ospfv3DefRtLeakP Properties

Property Name	Data Type	Description	Values
rtMap	string:Basic	The name of the default route leak policy route map. This route map name is used to control distribution.	A sequence of characters

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring to not Send Summary LSAs into a Stub Area

Configuring to not Send Summary LSAs into a Stub Area

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3Area": {
                      "attributes": {
                        "id": "1.2.3.4",
                        "redistribute": "no",
                        "summary": "no",
                        "supressFa": "no",
                        "type": "stub"
}}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>1.2.3.4</id>
                <redistribute>false</redistribute>
                <summary>false</summary>
                <supressFa>false</supressFa>
                <type>stub</type>
              </Area-list>
            </area-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
area 1.2.3.4 stub no-summary

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3Area	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters
redistribute	scalar:Bool	Send redistributed LSAs into NSSA area	SELECTION: true or false DEFAULT: true
summary	scalar:Bool	Originate summary LSA into other areas	SELECTION: true or false DEFAULT: true
supressFa	scalar:Bool	Supress forwarding address in translated LSA	SELECTION: true or false DEFAULT: false
type	ospfv3:AreaT (scalar:Enum8)	Configure area type as NSSA or stub	SELECTION: 1 - regular 2 - stub 3 - nssa DEFAULT: regular

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Send Summary LSAs into Stub Area

Configuring Send Summary LSAs into Stub Area

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3Area": {
                      "attributes": {
                        "id": "1.2.3.4",
                        "redistribute": "no",
                        "summary": "yes",
                        "supressFa": "no",
                        "type": "stub"
}}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>1.2.3.4</id>
                <redistribute>false</redistribute>
                <summary>true</summary>
                <supressFa>false</supressFa>
                <type>stub</type>
              </Area-list>
            </area-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
no area 1.2.3.4 stub no-summary

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3Area	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters
redistribute	scalar:Bool	Send redistributed LSAs into NSSA area	SELECTION: true or false DEFAULT: true
summary	scalar:Bool	Originate summary LSA into other areas	SELECTION: true or false DEFAULT: true
supressFa	scalar:Bool	Supress forwarding address in translated LSA	SELECTION: true or false DEFAULT: false
type	ospfv3:AreaT (scalar:Enum8)	Configure area type as NSSA or stub	SELECTION: 1 - regular 2 - stub 3 - nssa DEFAULT: regular

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring BFD under router instance

Configuring BFD under router instance

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "bfdCtrl": "yes",
                  "name": "default"
}}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <bfdCtrl>true</bfdCtrl>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
bfd

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
bfdCtrl	scalar:Bool	Holds the controls for bfd	SELECTION: true or false DEFAULT: false
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting BFD under router instance

Deleting BFD under router instance

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "bfdCtrl": "no",
                  "name": "default"
}}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <bfdCtrl>false</bfdCtrl>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
no bfd

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
bfdCtrl	scalar:Bool	Holds the controls for bfd	SELECTION: true or false DEFAULT: false
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring discard route external

Configuring discard route external

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "discardRouteExt": "yes",
                  "name": "default"
}}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <discardRouteExt>true</discardRouteExt>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
discard-route external

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
discardRouteExt	scalar:Bool	Holds the controls for discard-route external	SELECTION: true or false DEFAULT: true
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting discard route external

Deleting discard route external

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "discardRouteExt": "no",
                  "name": "default"
}}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <discardRouteExt>false</discardRouteExt>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
no discard-route external

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
discardRouteExt	scalar:Bool	Holds the controls for discard-route external	SELECTION: true or false DEFAULT: true
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring discard route internal

Configuring discard route internal

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "discardRouteInt": "yes",
                  "name": "default"
}}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <discardRouteInt>true</discardRouteInt>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
discard-route internal

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
discardRouteInt	scalar:Bool	Holds the controls for discard-route internal	SELECTION: true or false DEFAULT: true
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting discard route internal

Deleting discard route internal

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "discardRouteInt": "no",
                  "name": "default"
}}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <discardRouteInt>false</discardRouteInt>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
no discard-route internal

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
discardRouteInt	scalar:Bool	Holds the controls for discard-route internal	SELECTION: true or false DEFAULT: true
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Log Adjacency Change Details

Configuring Log Adjacency Change Details

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "adjChangeLogLevel": "detail",
                  "name": "default"
}}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <adjChangeLogLevel>detail</adjChangeLogLevel>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
log-adjacency-changes detail

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
adjChangeLogLevel	ospfv3:AdjChangeLogLevel (scalar:Enum8)	Adjacency change logging level	SELECTION: 0 - none 1 - brief 2 - detail DEFAULT: none
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Log Adjacency Change Details

Deleting Log Adjacency Change Details

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "adjChangeLogLevel": "none",
                  "name": "default"
}}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <adjChangeLogLevel>none</adjChangeLogLevel>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
no log-adjacency-changes detail

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
adjChangeLogLevel	ospfv3:AdjChangeLogLevel (scalar:Enum8)	Adjacency change logging level	SELECTION: 0 - none 1 - brief 2 - detail DEFAULT: none
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring maxLsa attributes

Configuring maxLsa attributes

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3MaxLsaP": {
                      "attributes": {
                        "ignoreCount": "1",
                        "ignoreTime": "1106",
                        "logWarning": "reject",
                        "maxLsa": "1",
                        "resetTime": "1106",
                        "thresholdVal": "34"
}}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <maxlsa-items>
              <ignoreCount>1</ignoreCount>
              <ignoreTime>1106</ignoreTime>
              <logWarning>reject</logWarning>
              <maxLsa>1</maxLsa>
              <resetTime>1106</resetTime>
              <thresholdVal>34</thresholdVal>
            </maxlsa-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
max-lsa 1 34 ignore-time 1106 ignore-count 1 reset-time 1106

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3MaxLsaP	sys/ospfv3/inst-Test_1/dom-default/maxlsa

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3MaxLsaP Properties

The following table contains information about the ospfv3MaxLsaP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
ignoreCount	ospf:SleepCnt (scalar:Uint32)	Set count on how many times adjacencies can be suppressed	RANGE: [1 , 4294967295] DEFAULT: 5
ignoreTime	ospf:SleepIntvl (scalar:Uint16)	Set time during which all adjacencies are suppressed	RANGE: [1 , 1440] DEFAULT: 5
logWarning	ospfv3:MaxLsaAct (scalar:Enum8)	Log a warning message when limit is exceeded	SELECTION: 0 - reject 1 - log DEFAULT: reject
maxLsa	ospf:MaxLsa (scalar:Uint32)	Set maximum number of non self-generated LSAs	RANGE: [1 , 4294967295]
resetTime	ospf:ResetIntvl (scalar:Uint32)	Set number of minutes after which ignore-count is reset to zero	RANGE: [1 , 1440] DEFAULT: 10
thresholdVal	ospf:MaxLsaThresh (scalar:Uint16)	Max LSA threshold percentage value at which to generate a warning message	RANGE: [1 , 100] DEFAULT: 75

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting the maxLsa attributes

Deleting the maxLsa attributes

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3MaxLsaP": {
                      "attributes": {
                        "status": "deleted"
}}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <maxlsa-items nc:operation="delete">
            </maxlsa-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
no max-lsa 1 34 ignore-time 1106 ignore-count 1 reset-time 1106

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3MaxLsaP	sys/ospfv3/inst-Test_1/dom-default/maxlsa

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3MaxLsaP Properties

Property Name	Data Type	Description	Values
status	mo:ModificationStatus (scalar:Bitmask32)	The upgrade status. This property is for internal use only.	SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring to Log a Warning Message When the maxLsa Limit is Exceeded

Configuring to Log a Warning Message When the maxLsa Limit is Exceeded

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3MaxLsaP": {
                      "attributes": {
                        "ignoreCount": "5",
                        "ignoreTime": "5",
                        "logWarning": "log",
                        "maxLsa": "1",
                        "resetTime": "10",
                        "thresholdVal": "34"
}}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <maxlsa-items>
              <ignoreCount>5</ignoreCount>
              <ignoreTime>5</ignoreTime>
              <logWarning>log</logWarning>
              <maxLsa>1</maxLsa>
              <resetTime>10</resetTime>
              <thresholdVal>34</thresholdVal>
            </maxlsa-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
max-lsa 1 34 warning-only

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3MaxLsaP	sys/ospfv3/inst-Test_1/dom-default/maxlsa

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3MaxLsaP Properties

Property Name	Data Type	Description	Values
ignoreCount	ospf:SleepCnt (scalar:Uint32)	Set count on how many times adjacencies can be suppressed	RANGE: [1 , 4294967295] DEFAULT: 5
ignoreTime	ospf:SleepIntvl (scalar:Uint16)	Set time during which all adjacencies are suppressed	RANGE: [1 , 1440] DEFAULT: 5
logWarning	ospfv3:MaxLsaAct (scalar:Enum8)	Log a warning message when limit is exceeded	SELECTION: 0 - reject 1 - log DEFAULT: reject
maxLsa	ospf:MaxLsa (scalar:Uint32)	Set maximum number of non self-generated LSAs	RANGE: [1 , 4294967295]
resetTime	ospf:ResetIntvl (scalar:Uint32)	Set number of minutes after which ignore-count is reset to zero	RANGE: [1 , 1440] DEFAULT: 10
thresholdVal	ospf:MaxLsaThresh (scalar:Uint16)	Max LSA threshold percentage value at which to generate a warning message	RANGE: [1 , 100] DEFAULT: 75

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting to Log a Warning Message When the maxLsa Limit is Exceeded

Deleting to Log a Warning Message When the maxLsa Limit is Exceeded

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3MaxLsaP": {
                      "attributes": {
                        "status": "deleted"
}}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <maxlsa-items nc:operation="delete">
            </maxlsa-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
no max-lsa 1 34 warning-only

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3MaxLsaP	sys/ospfv3/inst-Test_1/dom-default/maxlsa

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3MaxLsaP Properties

Property Name	Data Type	Description	Values
status	mo:ModificationStatus (scalar:Bitmask32)	The upgrade status. This property is for internal use only.	SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring max-metric router-lsa attributes

Configuring  max-metric router-lsa attributes

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3MaxMetricLsaP": {
                      "attributes": {
                        "awaitConvBgpAsn": "none",
                        "externalLsa": "yes",
                        "interAreaPrefixLsa": "yes",
                        "maxMetricExtLsaValue": "9664106",
                        "maxMetricSumLsaValue": "9664106",
                        "onStartup": "yes",
                        "startupIntvl": "59882",
                        "stubPrefixLsa": "yes"
}}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <maxmetriclsa-items>
              <awaitConvBgpAsn>none</awaitConvBgpAsn>
              <externalLsa>true</externalLsa>
              <interAreaPrefixLsa>true</interAreaPrefixLsa>
              <maxMetricExtLsaValue>9664106</maxMetricExtLsaValue>
              <maxMetricSumLsaValue>9664106</maxMetricSumLsaValue>
              <onStartup>true</onStartup>
              <startupIntvl>59882</startupIntvl>
              <stubPrefixLsa>true</stubPrefixLsa>
            </maxmetriclsa-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
max-metric router-lsa external-lsa 9664106 stub-prefix-lsa on-startup 59882 inter-area-prefix-lsa 9664106

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3MaxMetricLsaP	sys/ospfv3/inst-Test_1/dom-default/maxmetriclsa

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3MaxMetricLsaP Properties

The following table contains information about the ospfv3MaxMetricLsaP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
awaitConvBgpAsn	rtleak:Asn (string:Basic)	At startup, advertise max metric until convergence of BGP ASN	A sequence of characters DEFAULT: none
externalLsa	scalar:Bool	Set this to max-metric External LSAs	SELECTION: true or false
interAreaPrefixLsa	scalar:Bool	Set this to max-metric Inter-area-prefix LSAs	SELECTION: true or false
maxMetricExtLsaValue	ospf:MaxMetric (scalar:Uint32)	Maximum metric value for external LSAs	RANGE: [0 , 16777215]
maxMetricSumLsaValue	ospf:MaxMetric (scalar:Uint32)	Maximum metric value for Inter-area-prefix/Summary LSAs	RANGE: [0 , 16777215]
onStartup	scalar:Bool	Max metric advertised should be effective only at startup	SELECTION: true or false
startupIntvl	ospf:StartupIntvl (scalar:Uint32)	Wait period in seconds after which max metric should be advertised at startup	RANGE: [5 , 86400] DEFAULT: 600
stubPrefixLsa	scalar:Bool	Advertise Max metric for Stub links as well	SELECTION: true or false

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting max-metric router-lsa attributes

Deleting max-metric router-lsa attributes

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3MaxMetricLsaP": {
                      "attributes": {
                        "status": "deleted"
}}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <maxmetriclsa-items nc:operation="delete">
            </maxmetriclsa-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
no max-metric router-lsa external-lsa 9664106 stub-prefix-lsa on-startup 59882 inter-area-prefix-lsa 9664106

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3MaxMetricLsaP	sys/ospfv3/inst-Test_1/dom-default/maxmetriclsa

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3MaxMetricLsaP Properties

Property Name	Data Type	Description	Values
status	mo:ModificationStatus (scalar:Bitmask32)	The upgrade status. This property is for internal use only.	SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the LSA Arrival

Configuring the LSA Arrival

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3LsaCtrl": {
                      "attributes": {
                        "arrivalIntvl": "456817"
}}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <lsactrl-items>
              <arrivalIntvl>456817</arrivalIntvl>
            </lsactrl-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
timers lsa-arrival 456817

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3LsaCtrl	sys/ospfv3/inst-Test_1/dom-default/lsactrl

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3LsaCtrl Properties

The following table contains information about the ospfv3LsaCtrl properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
arrivalIntvl	ospfv3:LsaArrivalIntvl (scalar:Uint32)	Minimum interval between arrival of a LSA	RANGE: [10 , 600000] DEFAULT: 1000

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting the LSA Arrival

Deleting the LSA Arrival

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3LsaCtrl": {
                      "attributes": {
                        "arrivalIntvl": "1000"
}}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <lsactrl-items>
              <arrivalIntvl>1000</arrivalIntvl>
            </lsactrl-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
no timers lsa-arrival 456817

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3LsaCtrl	sys/ospfv3/inst-Test_1/dom-default/lsactrl

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3LsaCtrl Properties

Property Name	Data Type	Description	Values
arrivalIntvl	ospfv3:LsaArrivalIntvl (scalar:Uint32)	Minimum interval between arrival of a LSA	RANGE: [10 , 600000] DEFAULT: 1000

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Suppress of Forwarding Address in Translated LSAs

Configuring Suppress of Forwarding Address in Translated LSAs

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3Area": {
                      "attributes": {
                        "id": "1.2.3.4",
                        "nssaTransRole": "always",
                        "supressFa": "yes"
}}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>1.2.3.4</id>
                <nssaTransRole>always</nssaTransRole>
                <supressFa>true</supressFa>
              </Area-list>
            </area-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
area 1.2.3.4 nssa translate type7 always supress-fa

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3Area	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters
nssaTransRole	ospf:NssaTransRole (scalar:Enum8)	Not-so-stubby area(NSSA) translator role	SELECTION: 1 - always 2 - candidate 3 - never DEFAULT: candidate
supressFa	scalar:Bool	Supress forwarding address in translated LSA	SELECTION: true or false DEFAULT: false

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Suppress of Forwarding Address in Translated LSAs

Deleting Suppress of Forwarding Address in Translated LSAs

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3Area": {
                      "attributes": {
                        "id": "1.2.3.4",
                        "nssaTransRole": "candidate",
                        "supressFa": "no"
}}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>1.2.3.4</id>
                <nssaTransRole>candidate</nssaTransRole>
                <supressFa>false</supressFa>
              </Area-list>
            </area-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
no area 1.2.3.4 nssa translate type7 always supress-fa

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3Area	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters
nssaTransRole	ospf:NssaTransRole (scalar:Enum8)	Not-so-stubby area(NSSA) translator role	SELECTION: 1 - always 2 - candidate 3 - never DEFAULT: candidate
supressFa	scalar:Bool	Supress forwarding address in translated LSA	SELECTION: true or false DEFAULT: false

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configure authentication ipsec spi spi_id md5 authentication key

Configure authentication ipsec spi spi_id md5 authentication key

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "TEST_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3DomAuthNewP": {
                      "attributes": {
                        "authKey": "762bc328e3bdf23528634c34c4ee38d6e2113d0f74c1176d75968a592447ede0",
                        "authKeyEncrType": "3des",
                        "authType": "md5",
                        "spi": "4294967295"
}}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <auth-items>
              <authKey>762bc328e3bdf23528634c34c4ee38d6e2113d0f74c1176d75968a592447ede0</authKey>
              <authKeyEncrType>3des</authKeyEncrType>
              <authType>md5</authType>
              <spi>4294967295</spi>
            </auth-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
authentication ipsec spi 4294967295 md5 3 762bc328e3bdf23528634c34c4ee38d6e2113d0f74c1176d75968a592447ede0

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-TEST_1
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-default
ospfv3DomAuthNewP	sys/ospfv3/inst-TEST_1/dom-default/auth

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3DomAuthNewP Properties

The following table contains information about the ospfv3DomAuthNewP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
authKey	ospfv3:AuthKey (string:Password)	Key used for authentication
authKeyEncrType	ospfv3:AuthKeyEncrType (scalar:Enum8)	Authentication key encryption type which can be Cleartext, 3DES or CiscoType7	SELECTION: 0 - cleartext 3 - 3des 7 - cisco-type-7 DEFAULT: cleartext
authType	ospfv3:DomAuthType (scalar:Enum8)	Authentication types which can be md5 or sha1.	SELECTION: 0 - none 1 - md5 2 - sha1
spi	ospfv3:AuthSpi (scalar:Uint32)	Security Parameter Index	RANGE: [256 , 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Delete authentication ipsec spi spi_id md5 authentication key

Delete authentication ipsec spi spi_id md5 authentication key

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "TEST_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3DomAuthNewP": {
                      "attributes": {
                        "status": "deleted"
}}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <auth-items nc:operation="delete">
            </auth-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
no authentication ipsec spi 4294967295 md5 3 762bc328e3bdf23528634c34c4ee38d6e2113d0f74c1176d75968a592447ede0

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-TEST_1
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-default
ospfv3DomAuthNewP	sys/ospfv3/inst-TEST_1/dom-default/auth

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3DomAuthNewP Properties

Property Name	Data Type	Description	Values
status	mo:ModificationStatus (scalar:Bitmask32)	The upgrade status. This property is for internal use only.	SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configure authentication ipsec spi spi_id sha1 authentication key

Configure authentication ipsec spi spi_id sha1 authentication key

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "TEST_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3DomAuthNewP": {
                      "attributes": {
                        "authKey": "762bc328e3bdf23528634c34c4ee38d6e2113d0f74c1176de0d74f6a52d2265ad9f49aae9d7afc93",
                        "authKeyEncrType": "3des",
                        "authType": "sha1",
                        "spi": "10002"
}}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <auth-items>
              <authKey>762bc328e3bdf23528634c34c4ee38d6e2113d0f74c1176de0d74f6a52d2265ad9f49aae9d7afc93</authKey>
              <authKeyEncrType>3des</authKeyEncrType>
              <authType>sha1</authType>
              <spi>10002</spi>
            </auth-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
authentication ipsec spi 10002 sha1 3 762bc328e3bdf23528634c34c4ee38d6e2113d0f74c1176de0d74f6a52d2265ad9f49aae9d7afc93

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-TEST_1
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-default
ospfv3DomAuthNewP	sys/ospfv3/inst-TEST_1/dom-default/auth

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3DomAuthNewP Properties

Property Name	Data Type	Description	Values
authKey	ospfv3:AuthKey (string:Password)	Key used for authentication
authKeyEncrType	ospfv3:AuthKeyEncrType (scalar:Enum8)	Authentication key encryption type which can be Cleartext, 3DES or CiscoType7	SELECTION: 0 - cleartext 3 - 3des 7 - cisco-type-7 DEFAULT: cleartext
authType	ospfv3:DomAuthType (scalar:Enum8)	Authentication types which can be md5 or sha1.	SELECTION: 0 - none 1 - md5 2 - sha1
spi	ospfv3:AuthSpi (scalar:Uint32)	Security Parameter Index	RANGE: [256 , 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Delete authentication ipsec spi spi_id sha1 authentication key

Delete authentication ipsec spi spi_id  sha1 authentication key

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "TEST_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3DomAuthNewP": {
                      "attributes": {
                        "status": "deleted"
}}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <auth-items nc:operation="delete">
            </auth-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
no authentication ipsec spi 10002 sha1 3 762bc328e3bdf23528634c34c4ee38d6e2113d0f74c1176de0d74f6a52d2265ad9f49aae9d7afc93

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-TEST_1
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-default
ospfv3DomAuthNewP	sys/ospfv3/inst-TEST_1/dom-default/auth

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3DomAuthNewP Properties

Property Name	Data Type	Description	Values
status	mo:ModificationStatus (scalar:Bitmask32)	The upgrade status. This property is for internal use only.	SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring area authentication ipsec spi spi_id sha1 authentication key

Configuring area authentication ipsec spi spi_id sha1 authentication key

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
"ospfv3Entity": {
  "children": [
    {
      "ospfv3Inst": {
        "attributes": {
          "name": "TEST_1"
        },
        "children": [
          {
            "ospfv3Dom": {
              "attributes": {
                "name": "default"
              },
              "children": [
                {
                  "ospfv3Area": {
                    "attributes": {
                      "id": "0.0.0.101"
                    },
                    "children": [
                      {
                        "ospfv3AreaAuthNewP": {
                          "attributes": {
                            "authKey": "762bc328e3bdf23528634c34c4ee38d6
e2113d0f74c1176de0d74f6a52d2265ad9f49aae9d7afc93",
                            "authKeyEncrType": "3des",
                            "authType": "sha1",
                            "spi": "10002"
}}}]}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>0.0.0.101</id>
                <auth-items>
                  <authKey>762bc328e3bdf23528634c34c4ee38d6e2113d0f74c1176de0d74
f6a52d2265ad9f49aae9d7afc93</authKey>
                  <authKeyEncrType>3des</authKeyEncrType>
                  <authType>sha1</authType>
                  <spi>10002</spi>
                </auth-items>
              </Area-list>
            </area-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
area 0.0.0.101 authentication ipsec spi 10002 sha1 3 762bc328e3bdf23528634c34c4ee38d6e2113d0f74c1176de0d74f6a52d2265ad9f49aae9d7afc93

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-TEST_1
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-default
ospfv3Area	sys/ospfv3/inst-TEST_1/dom-default/area-0.0.0.101
ospfv3AreaAuthNewP	sys/ospfv3/inst-TEST_1/dom-default/area-0.0.0.101/auth

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters

ospfv3AreaAuthNewP Properties

The following table contains information about the ospfv3AreaAuthNewP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
status	mo:ModificationStatus (scalar:Bitmask32)	The upgrade status. This property is for internal use only.	SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Delete area authentication ipsec spi spi_id sha1 authentication key

Delete area authentication ipsec spi spi_id sha1 authentication key

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "TEST_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3Area": {
                      "attributes": {
                        "id": "0.0.0.101"
                      },
                      "children": [
                        {
                          "ospfv3AreaAuthNewP": {
                            "attributes": {
                              "status": "deleted"
}}}]}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>0.0.0.101</id>
                <auth-items nc:operation="delete">
                </auth-items>
              </Area-list>
            </area-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
no area 0.0.0.101 authentication ipsec spi 10002 sha1 3 762bc328e3bdf23528634c34c4ee38d6e2113d0f74c1176de0d74f6a52d2265ad9f49aae9d7afc93

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-TEST_1
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-default
ospfv3Area	sys/ospfv3/inst-TEST_1/dom-default/area-0.0.0.101
ospfv3AreaAuthNewP	sys/ospfv3/inst-TEST_1/dom-default/area-0.0.0.101/auth

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters

ospfv3AreaAuthNewP Properties

Property Name	Data Type	Description	Values
status	mo:ModificationStatus (scalar:Bitmask32)	The upgrade status. This property is for internal use only.	SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configure area authentication disable

Configure area authentication disable

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "TEST_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3Area": {
                      "attributes": {
                        "id": "0.0.0.101"
                      },
                      "children": [
                        {
                          "ospfv3AreaAuthNewP": {
                            "attributes": {
                              "authType": "disable"
}}}]}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>0.0.0.101</id>
                <auth-items>
                  <authType>disable</authType>
                </auth-items>
              </Area-list>
            </area-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
area 0.0.0.101 authentication disable

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-TEST_1
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-default
ospfv3Area	sys/ospfv3/inst-TEST_1/dom-default/area-0.0.0.101
ospfv3AreaAuthNewP	sys/ospfv3/inst-TEST_1/dom-default/area-0.0.0.101/auth

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters

ospfv3AreaAuthNewP Properties

Property Name	Data Type	Description	Values
authType	ospfv3:AuthType (scalar:Enum8)	Authentication types which can be md5, sha1 or disable.	SELECTION: 0 - none 1 - md5 2 - sha1 3 - disable

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configure area authentication ipsec spi spi_id md5 authentication key

Configure area authentication ipsec spi spi_id md5 authentication key

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "TEST_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3Area": {
                      "attributes": {
                        "id": "0.0.0.101"
                      },
                      "children": [
                        {
                          "ospfv3AreaAuthNewP": {
                            "attributes": {
                              "authKey": "762bc328e3bdf23528634c34c4ee38d6e2113d0f74c1176d75968a592447ede0",
                              "authKeyEncrType": "3des",
                              "authType": "md5",
                              "spi": "10000"
}}}]}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>0.0.0.101</id>
                <auth-items>
                  <authKey>762bc328e3bdf23528634c34c4ee38d6e2113d0f74c1176d75968a592447ede0</authKey>
                  <authKeyEncrType>3des</authKeyEncrType>
                  <authType>md5</authType>
                  <spi>10000</spi>
                </auth-items>
              </Area-list>
            </area-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
area 0.0.0.101 authentication ipsec spi 10000 md5 3 762bc328e3bdf23528634c34c4ee38d6e2113d0f74c1176d75968a592447ede0

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-TEST_1
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-default
ospfv3Area	sys/ospfv3/inst-TEST_1/dom-default/area-0.0.0.101
ospfv3AreaAuthNewP	sys/ospfv3/inst-TEST_1/dom-default/area-0.0.0.101/auth

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters

ospfv3AreaAuthNewP Properties

Property Name	Data Type	Description	Values
authKey	ospfv3:AuthKey (string:Password)	Key used for authentication
authKeyEncrType	ospfv3:AuthKeyEncrType (scalar:Enum8)	Authentication key encryption type which can be Cleartext, 3DES or CiscoType7	SELECTION: 0 - cleartext 3 - 3des 7 - cisco-type-7 DEFAULT: cleartext
authType	ospfv3:AuthType (scalar:Enum8)	Authentication types which can be md5, sha1 or disable.	SELECTION: 0 - none 1 - md5 2 - sha1 3 - disable
spi	ospfv3:AuthSpi (scalar:Uint32)	Security Parameter Index	RANGE: [256 , 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Delete area authentication ipsec spi spi_id md5 authentication key

Delete area authentication ipsec spi spi_id md5 authentication key

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "TEST_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      },
                      "children": [
                        {
                          "ospfv3Area": {
                            "attributes": {
                              "id": "0.0.0.101"
                            },
                            "children": [
                              {
                                "ospfv3AreaAuthNewP": {
                                  "attributes": {
                                    "status": "deleted"
                                  }
                                }
                              }
                            ]
                          }
                        }
                      ]
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>0.0.0.101</id>
                <auth-items nc:operation="delete">
                </auth-items>
              </Area-list>
            </area-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
no area 0.0.0.101 authentication ipsec spi 10000 md5 3 762bc328e3bdf23528634c34c4ee38d6e2113d0f74c1176d75968a592447ede0

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-TEST_1
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-default
ospfv3Area	sys/ospfv3/inst-TEST_1/dom-default/area-0.0.0.101
ospfv3AreaAuthNewP	sys/ospfv3/inst-TEST_1/dom-default/area-0.0.0.101/auth

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters

ospfv3AreaAuthNewP Properties

Property Name	Data Type	Description	Values
status	mo:ModificationStatus (scalar:Bitmask32)	The upgrade status. This property is for internal use only.	SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configure area authentication ipsec spi spi_id| sha1 authentication key

Configure area authentication ipsec spi spi_id| sha1 authentication key

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "TEST_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3Area": {
                      "attributes": {
                        "id": "0.0.0.101"
                      },
                      "children": [
                        {
                          "ospfv3AreaAuthNewP": {
                            "attributes": {
                              "authKey": "762bc328e3bdf23528634c34c4ee38d6e2113d0f74c1176de0d74f6a52d2265ad9f49aae9d7afc93",
                              "authKeyEncrType": "3des",
                              "authType": "sha1",
                              "spi": "10000"
}}}]}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>0.0.0.101</id>
                <auth-items>
                  <authKey>762bc328e3bdf23528634c34c4ee38d6e2113d0f74c1176de0d74f6a52d2265ad9f49aae9d7afc93</authKey>
                  <authKeyEncrType>3des</authKeyEncrType>
                  <authType>sha1</authType>
                  <spi>10000</spi>
                </auth-items>
              </Area-list>
            </area-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
area 0.0.0.101 authentication ipsec spi 10000 sha1 3 762bc328e3bdf23528634c34c4ee38d6e2113d0f74c1176de0d74f6a52d2265ad9f49aae9d7afc93

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-TEST_1
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-default
ospfv3Area	sys/ospfv3/inst-TEST_1/dom-default/area-0.0.0.101
ospfv3AreaAuthNewP	sys/ospfv3/inst-TEST_1/dom-default/area-0.0.0.101/auth

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters

ospfv3AreaAuthNewP Properties

Property Name	Data Type	Description	Values
authKey	ospfv3:AuthKey (string:Password)	Key used for authentication
authKeyEncrType	ospfv3:AuthKeyEncrType (scalar:Enum8)	Authentication key encryption type which can be Cleartext, 3DES or CiscoType7	SELECTION: 0 - cleartext 3 - 3des 7 - cisco-type-7 DEFAULT: cleartext
authType	ospfv3:AuthType (scalar:Enum8)	Authentication types which can be md5, sha1 or disable.	SELECTION: 0 - none 1 - md5 2 - sha1 3 - disable
spi	ospfv3:AuthSpi (scalar:Uint32)	Security Parameter Index	RANGE: [256 , 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting area authentication ipsec spi spi_id| sha1 authentication key

Deleting area authentication ipsec spi spi_id| sha1 authentication key

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
"ospfv3Entity": {
"children": [
{
  "ospfv3Inst": {
    "attributes": {
      "name": "TEST_1"
    },
    "children": [
      {
        "ospfv3Dom": {
          "attributes": {
            "name": "default"
          },
          "children": [
            {
              "ospfv3Area": {
                "attributes": {
                  "id": "0.0.0.101"
                },
                "children": [
                  {
                    "ospfv3AreaAuthNewP": {
                      "attributes": {
                        "status": "deleted"

}}}]}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>0.0.0.101</id>
                <auth-items nc:operation="delete">
                </auth-items>
              </Area-list>
            </area-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
no area 0.0.0.101 authentication ipsec spi 10000 sha1 3 762bc328e3bdf23528634c34c4ee38d6e2113d0f74c1176de0d74f6a52d2265ad9f49aae9d7afc93

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-TEST_1
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-default
ospfv3Area	sys/ospfv3/inst-TEST_1/dom-default/area-0.0.0.101
ospfv3AreaAuthNewP	sys/ospfv3/inst-TEST_1/dom-default/area-0.0.0.101/auth

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters

ospfv3AreaAuthNewP Properties

Property Name	Data Type	Description	Values
authKey	ospfv3:AuthKey (string:Password)	Key used for authentication
authKeyEncrType	ospfv3:AuthKeyEncrType (scalar:Enum8)	Authentication key encryption type which can be Cleartext, 3DES or CiscoType7	SELECTION: 0 - cleartext 3 - 3des 7 - cisco-type-7 DEFAULT: cleartext
authType	ospfv3:AuthType (scalar:Enum8)	Authentication types which can be md5, sha1 or disable.	SELECTION: 0 - none 1 - md5 2 - sha1 3 - disable
spi	ospfv3:AuthSpi (scalar:Uint32)	Security Parameter Index	RANGE: [256 , 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring to Never Translate LSAs

Configuring to Never Translate LSAs

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3Area": {
                      "attributes": {
                        "id": "1.2.3.4",
                        "nssaTransRole": "never",
                        "supressFa": "no"
}}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>1.2.3.4</id>
                <nssaTransRole>never</nssaTransRole>
                <supressFa>false</supressFa>
              </Area-list>
            </area-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
area 1.2.3.4 nssa translate type7 never

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3Area	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters
nssaTransRole	ospf:NssaTransRole (scalar:Enum8)	Not-so-stubby area(NSSA) translator role	SELECTION: 1 - always 2 - candidate 3 - never DEFAULT: candidate
supressFa	scalar:Bool	Supress forwarding address in translated LSA	SELECTION: true or false DEFAULT: false

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting to Never Translate LSAs

Deleting to Never Translate LSAs

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3Area": {
                      "attributes": {
                        "id": "1.2.3.4",
                        "nssaTransRole": "candidate",
                        "supressFa": "no"
}}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>1.2.3.4</id>
                <nssaTransRole>candidate</nssaTransRole>
                <supressFa>false</supressFa>
              </Area-list>
            </area-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
no area 1.2.3.4 nssa translate type7 never

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3Area	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters
nssaTransRole	ospf:NssaTransRole (scalar:Enum8)	Not-so-stubby area(NSSA) translator role	SELECTION: 1 - always 2 - candidate 3 - never DEFAULT: candidate
supressFa	scalar:Bool	Supress forwarding address in translated LSA	SELECTION: true or false DEFAULT: false

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Reference Bandwidth in Mbps/Gbps

Configuring the Reference Bandwidth in Mbps/Gbps

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "bwRef": "1039771",
                  "bwRefUnit": "mbps",
                  "name": "default"
}}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <bwRef>1039771</bwRef>
            <bwRefUnit>mbps</bwRefUnit>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
auto-cost reference-bandwidth 1039771 Mbps

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
bwRef	ospfv3:BwRef (scalar:Uint32)	Bandwidth reference value, holds the range from 1-4000000 if unit is mbps and holds range from 1-4000 if unit is gbps	RANGE: [0, 4294967295] DEFAULT: 40000
bwRefUnit	ospfv3:BwRefUnit (scalar:Enum8)	Bandwidth reference unit (Mbps or Gbps)	SELECTION: 0 - mbps 1 - gbps DEFAULT: mbps
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting the Reference Bandwidth in Mbps/Gbps

Deleting the Reference Bandwidth in Mbps/Gbps

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "bwRef": "40000",
                  "bwRefUnit": "mbps",
                  "name": "default"
}}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <bwRef>40000</bwRef>
            <bwRefUnit>mbps</bwRefUnit>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
no auto-cost reference-bandwidth 1039771 Mbps

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
bwRef	ospfv3:BwRef (scalar:Uint32)	Bandwidth reference value, holds the range from 1-4000000 if unit is mbps and holds range from 1-4000 if unit is gbps	RANGE: [0, 4294967295] DEFAULT: 40000
bwRefUnit	ospfv3:BwRefUnit (scalar:Enum8)	Bandwidth reference unit (Mbps or Gbps)	SELECTION: 0 - mbps 1 - gbps DEFAULT: mbps
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Cost for Range of networks

Configuring the Cost for Range of networks

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      },
                      "children": [
                        {
                          "ospfv3Area": {
                            "attributes": {
                              "id": "1.2.3.4"
                            },
                            "children": [
                              {
                                "ospfv3AreaAf": {
                                  "attributes": {
                                    "type": "ipv6-ucast"
                                  },
                                  "children": [
                                    {
                                      "ospfv3InterAreaRtSum": {
                                        "attributes": {
                                          "addr": "1:2::3:4/24",
                                          "cost": "15278324",
                                          "ctrl": "no-advertise"
                                        }
                                      }
                                    }
                                  ]
                                }
                              }
                            ]
                          }
                        },
                        {
                          "ospfv3DomAf": {
                            "attributes": {
                              "type": "ipv6-ucast"
                            }
                          }
                        }
                      ]
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>1.2.3.4</id>
                <areaaf-items>
                  <AreaAf-list>
                    <type>ipv6-ucast</type>
                    <iartsum-items>
                      <InterAreaRtSum-list>
                        <addr>1:2::3:4/24</addr>
                        <cost>15278324</cost>
                        <ctrl>no-advertise</ctrl>
                      </InterAreaRtSum-list>
                    </iartsum-items>
                  </AreaAf-list>
                </areaaf-items>
              </Area-list>
            </area-items>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
address-family ipv6 unicast
area 1.2.3.4 range 1:2::3:4/24 not-advertise cost 15278324

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3Area	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4
ospfv3AreaAf	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4/areaaf-ipv6-ucast
ospfv3InterAreaRtSum	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4/areaaf-ipv6-ucast/iartsum-[1:2::3:4/24]
ospfv3DomAf	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters

ospfv3AreaAf Properties

The following table contains information about the ospfv3AreaAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	Unicast IP address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

ospfv3InterAreaRtSum Properties

The following table contains information about the ospfv3InterAreaRtSum properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
addr	address:Ip	Address	Value must match ipv4 or ipv6 known format
cost	ospf:SumCost (scalar:Uint32)	Area range cost for route summarization	RANGE: [0 , 16777216] DEFAULT: unspecified
ctrl	ospf:SumControl (scalar:Bitmask8)	Summary address no advertise	SELECTION: 0 - unspecified 1 - no-advertise DEFAULT: unspecified

ospfv3DomAf Properties

The following table contains information about the ospfv3DomAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Delete the Cost for Range of networks

Delete the Cost for Range of networks

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      },
                      "children": [
                        {
                          "ospfv3Area": {
                            "attributes": {
                              "id": "1.2.3.4"
                            },
                            "children": [
                              {
                                "ospfv3AreaAf": {
                                  "attributes": {
                                    "type": "ipv6-ucast"
                                  },
                                  "children": [
                                    {
                                      "ospfv3InterAreaRtSum": {
                                        "attributes": {
                                          "addr": "1:2::3:4/24",
                                          "cost": "15278324",
                                          "ctrl": "no-advertise"
                                        }
                                      }
                                    }
                                  ]
                                }
                              }
                            ]
                          }
                        },
                        {
                          "ospfv3DomAf": {
                            "attributes": {
                              "type": "ipv6-ucast"
                            }
                          }
                        }
                      ]
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>1.2.3.4</id>
                <areaaf-items>
                  <AreaAf-list>
                    <type>ipv6-ucast</type>
                    <iartsum-items>
                      <InterAreaRtSum-list>
                        <addr>1:2::3:4/24</addr>
                        <cost>15278324</cost>
                        <ctrl>no-advertise</ctrl>
                      </InterAreaRtSum-list>
                    </iartsum-items>
                  </AreaAf-list>
                </areaaf-items>
              </Area-list>
            </area-items>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
address-family ipv6 unicast
no area 1.2.3.4 range 1:2::3:4/24 not-advertise cost 15278324

Configuring the Summary Address as Not Advertise

Configuring the Summary Address as Not Advertise

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      },
                      "children": [
                        {
                          "ospfv3DomAf": {
                            "attributes": {
                              "type": "ipv6-ucast"
                            },
                            "children": [
                              {
                                "ospfv3ExtRtSum": {
                                  "attributes": {
                                    "addr": "1:2::3:4/24",
                                    "ctrl": "no-advertise",
                                    "tag": "0"
                                  }
                                }
                              }
                            ]
                          }
                        }
                      ]
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
**Note:** Only one instance, either ctrl or tag can be used at a time. 	
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
                <extrtsum-items>
                  <ExtRtSum-list>
                    <addr>1:2::3:4/24</addr>
                    <ctrl>no-advertise</ctrl>
                    <tag>0</tag>
                  </ExtRtSum-list>
                </extrtsum-items>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
address-family ipv6 unicast
summary-address 1:2::3:4/24 not-advertise

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3DomAf	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast
ospfv3ExtRtSum	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast/extrtsum-[1:2::3:4/24]

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3DomAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

ospfv3ExtRtSum Properties

The following table contains information about the ospfv3ExtRtSum properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
addr	address:Ip	Address	Value must match ipv4 or ipv6 known format
ctrl	ospf:SumControl (scalar:Bitmask8)	Summary address no advertise	SELECTION: 0 - unspecified 1 - no-advertise DEFAULT: unspecified
tag	ospf:RtTag (scalar:Uint32)	Route tag of external route	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting the Summary Address as Not Advertise

Deleting the Summary Address as Not Advertise

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3DomAf": {
                      "attributes": {
                        "type": "ipv6-ucast"
                      },
                      "children": [
                        {
                          "ospfv3ExtRtSum": {
                            "attributes": {
                              "addr": "1:2::3:4/24",
                              "status": "deleted"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
                <extrtsum-items>
                  <ExtRtSum-list nc:operation="delete">
                    <addr>1:2::3:4/24</addr>
                  </ExtRtSum-list>
                </extrtsum-items>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
address-family ipv6 unicast
no summary-address 1:2::3:4/24 not-advertise

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3DomAf	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast
ospfv3ExtRtSum	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast/extrtsum-[1:2::3:4/24]

ospfv3ExtRtSum Properties

Property Name	Data Type	Description	Values
addr	address:Ip	Address	Value must match ipv4 or ipv6 known format
status	mo:ModificationStatus (scalar:Bitmask32)	The upgrade status. This property is for internal use only.	SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3DomAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Summary Address

Configuring the Summary Address

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3DomAf": {
                      "attributes": {
                        "type": "ipv6-ucast"
                      },
                      "children": [
                        {
                          "ospfv3ExtRtSum": {
                            "attributes": {
                              "addr": "1:2::3:4/24",
                              "ctrl": "",
                              "tag": "1"
}}}]}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
                <extrtsum-items>
                  <ExtRtSum-list>
                    <addr>1:2::3:4/24</addr>
                    <ctrl></ctrl>
                    <tag>1</tag>
                  </ExtRtSum-list>
                </extrtsum-items>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
address-family ipv6 unicast
summary-address 1:2::3:4/24 tag 1

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3DomAf	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast
ospfv3ExtRtSum	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast/extrtsum-[1:2::3:4/24]

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3DomAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

ospfv3ExtRtSum Properties

Property Name	Data Type	Description	Values
addr	address:Ip	Address	Value must match ipv4 or ipv6 known format
ctrl	ospf:SumControl (scalar:Bitmask8)	Summary address no advertise	SELECTION: 0 - unspecified 1 - no-advertise DEFAULT: unspecified
tag	ospf:RtTag (scalar:Uint32)	Route tag of external route	RANGE: [0, 4294967295]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting the Summary Address

Deleting the Summary Address

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3DomAf": {
                      "attributes": {
                        "type": "ipv6-ucast"
                      },
                      "children": [
                        {
                          "ospfv3ExtRtSum": {
                            "attributes": {
                              "addr": "1:2::3:4/24",
                              "status": "deleted"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
                <extrtsum-items>
                  <ExtRtSum-list nc:operation="delete">
                    <addr>1:2::3:4/24</addr>
                  </ExtRtSum-list>
                </extrtsum-items>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
address-family ipv6 unicast
no summary-address 1:2::3:4/24 tag 1

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3DomAf	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast
ospfv3ExtRtSum	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast/extrtsum-[1:2::3:4/24]

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3DomAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

ospfv3ExtRtSum Properties

Property Name	Data Type	Description	Values
addr	address:Ip	Address	Value must match ipv4 or ipv6 known format
status	mo:ModificationStatus (scalar:Bitmask32)	The upgrade status. This property is for internal use only.	SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Table Map Filter

Configuring Table Map Filter

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3DomAf": {
                      "attributes": {
                        "type": "ipv6-ucast"
                      },
                      "children": [
                        {
                          "ospfv3RibLeakP": {
                            "attributes": {
                              "always": "no",
                              "rtMap": "SampleString_123"
}}}]}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
                <ribleak-items>
                  <always>false</always>
                  <rtMap>SampleString_123</rtMap>
                </ribleak-items>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
address-family ipv6 unicast
table-map SampleString_123 filter

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3DomAf	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast
ospfv3RibLeakP	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast/ribleak

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3DomAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

ospfv3RibLeakP Properties

The following table contains information about the ospfv3RibLeakP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
always	rtleak:Always (scalar:Bool)	Filter routes into RIB	SELECTION: true or false DEFAULT: true
rtMap	string:Basic	Route Map	A sequence of characters

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Table Map Filter

Deleting Table Map Filter

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3DomAf": {
                      "attributes": {
                        "type": "ipv6-ucast"
                      },
                      "children": [
                        {
                          "ospfv3RibLeakP": {
                            "attributes": {
                              "status": "deleted"
}}}]}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
                <ribleak-items nc:operation="delete">
                </ribleak-items>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
address-family ipv6 unicast
no table-map SampleString_123 filter

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3DomAf	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast
ospfv3RibLeakP	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast/ribleak

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3DomAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

ospfv3RibLeakP Properties

Property Name	Data Type	Description	Values
status	mo:ModificationStatus (scalar:Bitmask32)	The upgrade status. This property is for internal use only.	SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring area level filter-list route-map

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      },
                      "children": [
                        {
                          "ospfv3Area": {
                            "attributes": {
                              "id": "1.2.3.4"
                            },
                            "children": [
                              {
                                "ospfv3AreaAf": {
                                  "attributes": {
                                    "type": "ipv6-ucast"
                                  },
                                  "children": [
                                    {
                                      "ospfv3LsaLeakCtrlP": {
                                        "attributes": {
                                          "direction": "in",
                                          "rtMap": "SampleString_123"
                                        }
                                      }
                                    }
                                  ]
                                }
                              }
                            ]
                          }
                        },
                        {
                          "ospfv3DomAf": {
                            "attributes": {
                              "type": "ipv6-ucast"
                            }
                          }
                        }
                      ]
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>1.2.3.4</id>
                <areaaf-items>
                  <AreaAf-list>
                    <type>ipv6-ucast</type>
                    <lsaleakctrlp-items>
                      <LsaLeakCtrlP-list>
                        <direction>in</direction>
                        <rtMap>SampleString_123</rtMap>
                      </LsaLeakCtrlP-list>
                    </lsaleakctrlp-items>
                  </AreaAf-list>
                </areaaf-items>
              </Area-list>
            </area-items>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
address-family ipv6 unicast
area 1.2.3.4 filter-list route-map SampleString_123 in

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3Area	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4
ospfv3AreaAf	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4/areaaf-ipv6-ucast
ospfv3LsaLeakCtrlP	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4/areaaf-ipv6-ucast/lsaleakctrlp-in
ospfv3DomAf	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters

ospfv3AreaAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	Unicast IP address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

ospfv3LsaLeakCtrlP Properties

The following table contains information about the ospfv3LsaLeakCtrlP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
direction	rtleak:RtCtrlDir (scalar:Enum8)	Direction: Specifies whether to apply this policy in the incoming or outgoing direction.	SELECTION: 0 - in 1 - out DEFAULT: in
rtMap	string:Basic	The name of the default route leak policy route map. This route map name is used to control distribution.	A sequence of characters

ospfv3DomAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting area level filter-list route-map

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      },
                      "children": [
                        {
                          "ospfv3Area": {
                            "attributes": {
                              "id": "1.2.3.4"
                            },
                            "children": [
                              {
                                "ospfv3AreaAf": {
                                  "attributes": {
                                    "type": "ipv6-ucast"
                                  },
                                  "children": [
                                    {
                                      "ospfv3LsaLeakCtrlP": {
                                        "attributes": {
                                          "direction": "in",
                                          "rtMap": "SampleString_123"
                                        }
                                      }
                                    }
                                  ]
                                }
                              }
                            ]
                          }
                        },
                        {
                          "ospfv3DomAf": {
                            "attributes": {
                              "type": "ipv6-ucast"
                            }
                          }
                        }
                      ]
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>1.2.3.4</id>
                <areaaf-items>
                  <AreaAf-list>
                    <type>ipv6-ucast</type>
                    <lsaleakctrlp-items>
                      <LsaLeakCtrlP-list>
                        <direction>in</direction>
                        <rtMap>SampleString_123</rtMap>
                      </LsaLeakCtrlP-list>
                    </lsaleakctrlp-items>
                  </AreaAf-list>
                </areaaf-items>
              </Area-list>
            </area-items>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
address-family ipv6 unicast
no area 1.2.3.4 filter-list route-map SampleString_123 in

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3Area	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4
ospfv3AreaAf	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4/areaaf-ipv6-ucast
ospfv3LsaLeakCtrlP	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4/areaaf-ipv6-ucast/lsaleakctrlp-in
ospfv3DomAf	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters

ospfv3AreaAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	Unicast IP address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

ospfv3LsaLeakCtrlP Properties

Property Name	Data Type	Description	Values
direction	rtleak:RtCtrlDir (scalar:Enum8)	Direction: Specifies whether to apply this policy in the incoming or outgoing direction.	SELECTION: 0 - in 1 - out DEFAULT: in
rtMap	string:Basic	The name of the default route leak policy route map. This route map name is used to control distribution.	A sequence of characters

ospfv3DomAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Filter Networks Sent from This Area

Configuring Filter Networks Sent from This Area

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      },
                      "children": [
                        {
                          "ospfv3Area": {
                            "attributes": {
                              "id": "1.2.3.4"
                            },
                            "children": [
                              {
                                "ospfv3AreaAf": {
                                  "attributes": {
                                    "type": "ipv6-ucast"
                                  },
                                  "children": [
                                    {
                                      "ospfv3LsaLeakCtrlP": {
                                        "attributes": {
                                          "direction": "out",
                                          "rtMap": "SampleString_123"
                                        }
                                      }
                                    }
                                  ]
                                }
                              }
                            ]
                          }
                        },
                        {
                          "ospfv3DomAf": {
                            "attributes": {
                              "type": "ipv6-ucast"
                            }
                          }
                        }
                      ]
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>1.2.3.4</id>
                <areaaf-items>
                  <AreaAf-list>
                    <type>ipv6-ucast</type>
                    <lsaleakctrlp-items>
                      <LsaLeakCtrlP-list>
                        <direction>out</direction>
                        <rtMap>SampleString_123</rtMap>
                      </LsaLeakCtrlP-list>
                    </lsaleakctrlp-items>
                  </AreaAf-list>
                </areaaf-items>
              </Area-list>
            </area-items>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
address-family ipv6 unicast
area 1.2.3.4 filter-list route-map SampleString_123 out

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3Area	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4
ospfv3AreaAf	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4/areaaf-ipv6-ucast
ospfv3LsaLeakCtrlP	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4/areaaf-ipv6-ucast/lsaleakctrlp-out
ospfv3DomAf	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters

ospfv3AreaAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	Unicast IP address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

ospfv3LsaLeakCtrlP Properties

Property Name	Data Type	Description	Values
direction	rtleak:RtCtrlDir (scalar:Enum8)	Direction: Specifies whether to apply this policy in the incoming or outgoing direction.	SELECTION: 0 - in 1 - out DEFAULT: in
rtMap	string:Basic	The name of the default route leak policy route map. This route map name is used to control distribution.	A sequence of characters

ospfv3DomAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Filter Networks Sent from This Area

Deleting Filter Networks Sent from This Area

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      },
                      "children": [
                        {
                          "ospfv3Area": {
                            "attributes": {
                              "id": "1.2.3.4"
                            },
                            "children": [
                              {
                                "ospfv3AreaAf": {
                                  "attributes": {
                                    "type": "ipv6-ucast"
                                  },
                                  "children": [
                                    {
                                      "ospfv3LsaLeakCtrlP": {
                                        "attributes": {
                                          "direction": "out",
                                          "rtMap": "SampleString_123"
                                        }
                                      }
                                    }
                                  ]
                                }
                              }
                            ]
                          }
                        },
                        {
                          "ospfv3DomAf": {
                            "attributes": {
                              "type": "ipv6-ucast"
                            }
                          }
                        }
                      ]
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>1.2.3.4</id>
                <areaaf-items>
                  <AreaAf-list>
                    <type>ipv6-ucast</type>
                    <lsaleakctrlp-items>
                      <LsaLeakCtrlP-list>
                        <direction>out</direction>
                        <rtMap>SampleString_123</rtMap>
                      </LsaLeakCtrlP-list>
                    </lsaleakctrlp-items>
                  </AreaAf-list>
                </areaaf-items>
              </Area-list>
            </area-items>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
address-family ipv6 unicast
no area 1.2.3.4 filter-list route-map SampleString_123 out

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3Area	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4
ospfv3AreaAf	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4/areaaf-ipv6-ucast
ospfv3LsaLeakCtrlP	sys/ospfv3/inst-Test_1/dom-default/area-1.2.3.4/areaaf-ipv6-ucast/lsaleakctrlp-out
ospfv3DomAf	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters

ospfv3AreaAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	Unicast IP address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

ospfv3LsaLeakCtrlP Properties

Property Name	Data Type	Description	Values
direction	rtleak:RtCtrlDir (scalar:Enum8)	Direction: Specifies whether to apply this policy in the incoming or outgoing direction.	SELECTION: 0 - in 1 - out DEFAULT: in
rtMap	string:Basic	The name of the default route leak policy route map. This route map name is used to control distribution.	A sequence of characters

ospfv3DomAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring to Log a Warning Message When redistribution prefix Limit is Exceeded

Configuring to Log a Warning Message When redistribution prefix Limit is Exceeded

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3DomAf": {
                      "attributes": {
                        "type": "ipv6-ucast"
                      },
                      "children": [
                        {
                          "ospfv3LeakCtrlP": {
                            "attributes": {
                              "ctrl": "warning",
                              "duration": "300",
                              "max": "46706",
                              "retries": "1",
                              "thresh": "56"
}}}]}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
                <leakctrl-items>
                  <ctrl>warning</ctrl>
                  <duration>300</duration>
                  <max>46706</max>
                  <retries>1</retries>
                  <thresh>56</thresh>
                </leakctrl-items>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
address-family ipv6 unicast
redistribute maximum-prefix 46706 56 warning-only

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3DomAf	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast
ospfv3LeakCtrlP	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast/leakctrl

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3DomAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

ospfv3LeakCtrlP Properties

The following table contains information about the ospfv3LeakCtrlP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
ctrl	rtleak:Ctrl (scalar:Enum8)	The control state.	SELECTION: 0 - unspecified 1 - warning 2 - withdraw DEFAULT: unspecified
duration	rtleak:Duration (scalar:Uint16)	Duration	RANGE: [60 , 600] DEFAULT: 300
max	rtleak:MaxPfx (scalar:Uint16)	Maximum Limit	RANGE: [1 , 0xffff]
retries	rtleak:Retries (scalar:Uint16)	The number of attempts that a provider, method, or route is tried.	RANGE: [1 , 12] DEFAULT: 1
thresh	rtleak:Thresh (scalar:UByte)	The threshold for a maximum number of prefixes before a warning is issued. For example, if the maximum number is 10 and the threshold is set at 70%, a warning is issued when the number of prefixes exceeds 7 (70%).	RANGE: [1 , 100] DEFAULT: 75

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting to Log a Warning Message When redistribution prefix Limit is Exceeded

Deleting to Log a Warning Message When redistribution prefix Limit is Exceeded

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3DomAf": {
                      "attributes": {
                        "type": "ipv6-ucast"
                      },
                      "children": [
                        {
                          "ospfv3LeakCtrlP": {
                            "attributes": {
                              "status": "deleted"
}}}]}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
                <leakctrl-items nc:operation="delete">
                </leakctrl-items>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
address-family ipv6 unicast
no redistribute maximum-prefix 46706 56 warning-only

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3DomAf	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast
ospfv3LeakCtrlP	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast/leakctrl

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3DomAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

ospfv3LeakCtrlP Properties

Property Name	Data Type	Description	Values
status	mo:ModificationStatus (scalar:Bitmask32)	The upgrade status. This property is for internal use only.	SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring to Withdraw All Redistributed Routes

Configuring to Withdraw All Redistributed Routes

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3DomAf": {
                      "attributes": {
                        "type": "ipv6-ucast"
                      },
                      "children": [
                        {
                          "ospfv3LeakCtrlP": {
                            "attributes": {
                              "ctrl": "withdraw",
                              "duration": "555",
                              "max": "46706",
                              "retries": "10",
                              "thresh": "56"
}}}]}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
                <leakctrl-items>
                  <ctrl>withdraw</ctrl>
                  <duration>555</duration>
                  <max>46706</max>
                  <retries>10</retries>
                  <thresh>56</thresh>
                </leakctrl-items>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
address-family ipv6 unicast
redistribute maximum-prefix 46706 56 withdraw 10 555

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3DomAf	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast
ospfv3LeakCtrlP	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast/leakctrl

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3DomAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

ospfv3LeakCtrlP Properties

Property Name	Data Type	Description	Values
ctrl	rtleak:Ctrl (scalar:Enum8)	The control state.	SELECTION: 0 - unspecified 1 - warning 2 - withdraw DEFAULT: unspecified
duration	rtleak:Duration (scalar:Uint16)	Duration	RANGE: [60 , 600] DEFAULT: 300
max	rtleak:MaxPfx (scalar:Uint16)	Maximum Limit	RANGE: [1 , 0xffff]
retries	rtleak:Retries (scalar:Uint16)	The number of attempts that a provider, method, or route is tried.	RANGE: [1 , 12] DEFAULT: 1
thresh	rtleak:Thresh (scalar:UByte)	The threshold for a maximum number of prefixes before a warning is issued. For example, if the maximum number is 10 and the threshold is set at 70%, a warning is issued when the number of prefixes exceeds 7 (70%).	RANGE: [1 , 100] DEFAULT: 75

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting to Withdraw All Redistributed Routes

Deleting to Withdraw All Redistributed Routes

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3DomAf": {
                      "attributes": {
                        "type": "ipv6-ucast"
                      },
                      "children": [
                        {
                          "ospfv3LeakCtrlP": {
                            "attributes": {
                              "status": "deleted"
}}}]}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
                <leakctrl-items nc:operation="delete">
                </leakctrl-items>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
address-family ipv6 unicast
no redistribute maximum-prefix 46706 56 withdraw 10 555

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3DomAf	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast
ospfv3LeakCtrlP	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast/leakctrl

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3DomAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

ospfv3LeakCtrlP Properties

Property Name	Data Type	Description	Values
status	mo:ModificationStatus (scalar:Bitmask32)	The upgrade status. This property is for internal use only.	SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Maximum Paths

Configuring Maximum Paths

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3DomAf": {
                      "attributes": {
                        "maxEcmp": "38",
                        "type": "ipv6-ucast"
}}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
                <maxEcmp>38</maxEcmp>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
address-family ipv6 unicast
maximum-paths 38

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3DomAf	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3DomAf Properties

Property Name	Data Type	Description	Values
maxEcmp	ospfv3:Ecmp (scalar:UByte)	Maximum Equal Cost Multi Path(ECMP)	RANGE: [1 , 64] DEFAULT: 8
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Maximum Paths

Deleting Maximum Paths

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "Test_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3DomAf": {
                      "attributes": {
                        "maxEcmp": "8",
                        "type": "ipv6-ucast"
}}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
                <maxEcmp>8</maxEcmp>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
address-family ipv6 unicast
no maximum-paths 38

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default
ospfv3DomAf	sys/ospfv3/inst-Test_1/dom-default/af-ipv6-ucast

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3DomAf Properties

Property Name	Data Type	Description	Values
maxEcmp	ospfv3:Ecmp (scalar:UByte)	Maximum Equal Cost Multi Path(ECMP)	RANGE: [1 , 64] DEFAULT: 8
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuration of OSPFv3 timers throttle LSA

Configuration of OSPFv3 timers throttle LSA

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

router ospfv3 100
  vrf 200
     timers throttle lsa 5000 30000 30000

DME:
{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "100"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "200"
                      },
                      "children": [
                        {
                          "ospfv3LsaCtrl": {
                            "attributes": {
                              "holdIntvl": "30000",
                              "maxIntvl": "30000",
                              "startIntvl": "5000"
                            }
                          }
                        }
                      ]
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

<System>
  <ospfv3-items>
          <inst-items>
            <Inst-list>
              <name>100</name>
              <dom-items>
                <Dom-list>
                  <name>200</name>
                  <lsactrl-items>
                    <startIntvl>5000</startIntvl>
                    <holdIntvl>30000</holdIntvl>
                    <maxIntvl>30000</maxIntvl>
                  </lsactrl-items>
                </Dom-list>
              </dom-items>
            </Inst-list>
          </inst-items>
        </ospfv3-items>
      </System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 100
vrf 200
timers throttle lsa 5000 30000 30000

Deletion of OSPFv3 timers throttle LSA

Deletion of OSPFv3 timers throttle LSA

  vrf 200
     no timers throttle lsa 5000 30000 30000

DME:
{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "100"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "200"
                      },
                      "children": [
                        {
                          "ospfv3LsaCtrl": {
                            "attributes": {
                              "holdIntvl": "5000",
                              "maxIntvl": "5000",
                              "startIntvl": "0"
                            }
                          }
                        }
                      ]
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

<System>
  <ospfv3-items>
          <inst-items>
            <Inst-list>
              <name>100</name>
              <dom-items>
                <Dom-list>
                  <name>200</name>
                  <lsactrl-items xmlns:nc="urn:ietf:params:xml:ns:netconf:base:1.0" nc:operation="delete">
                    <startIntvl>5000</startIntvl>
                    <holdIntvl>30000</holdIntvl>
                    <maxIntvl>30000</maxIntvl>
                  </lsactrl-items>
                </Dom-list>
              </dom-items>
            </Inst-list>
          </inst-items>
        </ospfv3-items>
      </System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 100
vrf 200
no timers throttle lsa 5000 30000 30000

Configure timers throttle spf start-time hold-time max-time

Configure timers throttle spf start-time hold-time max-time

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "TEST_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3DomAf": {
                      "attributes": {
                        "type": "ipv6-ucast"
                      },
                      "children": [
                        {
                          "ospfv3SpfComp": {
                            "attributes": {
                              "holdIntvl": "600000",
                              "initIntvl": "600000",
                              "maxIntvl": "600000"
}}}]}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
                <spfcomp-items>
                  <holdIntvl>600000</holdIntvl>
                  <initIntvl>600000</initIntvl>
                  <maxIntvl>600000</maxIntvl>
                </spfcomp-items>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
address-family ipv6 unicast
timers throttle spf 600000 600000 600000

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-TEST_1
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-default
ospfv3DomAf	sys/ospfv3/inst-TEST_1/dom-default/af-ipv6-ucast
ospfv3SpfComp	sys/ospfv3/inst-TEST_1/dom-default/af-ipv6-ucast/spfcomp

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3DomAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

ospfv3SpfComp Properties

The following table contains information about the ospfv3SpfComp properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
holdIntvl	ospfv3:SpfCompHoldIntvl (scalar:Uint32)	Minimum hold time interval between SPF calculations	RANGE: [1 , 600000] DEFAULT: 1000
initIntvl	ospfv3:SpfCompInitIntvl (scalar:Uint32)	Initial SPF schedule delay interval	RANGE: [1 , 600000] DEFAULT: 200
maxIntvl	ospfv3:SpfCompMaxIntvl (scalar:Uint32)	Maximum wait time between SPF calculations	RANGE: [1 , 600000] DEFAULT: 5000

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Delete timers throttle spf start-time hold-time max-time

Delete timers throttle spf start-time hold-time max-time

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "TEST_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3DomAf": {
                      "attributes": {
                        "type": "ipv6-ucast"
                      },
                      "children": [
                        {
                          "ospfv3SpfComp": {
                            "attributes": {
                              "status": "deleted"
}}}]}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
                <spfcomp-items nc:operation="delete">
                </spfcomp-items>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
address-family ipv6 unicast
no timers throttle spf 600000 600000 600000

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-TEST_1
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-default
ospfv3DomAf	sys/ospfv3/inst-TEST_1/dom-default/af-ipv6-ucast
ospfv3SpfComp	sys/ospfv3/inst-TEST_1/dom-default/af-ipv6-ucast/spfcomp

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3DomAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

ospfv3SpfComp Properties

Property Name	Data Type	Description	Values
status	mo:ModificationStatus (scalar:Bitmask32)	The upgrade status. This property is for internal use only.	SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configure area default-cost

Configure area default-cost

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "TEST_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      },
                      "children": [
                        {
                          "ospfv3Area": {
                            "attributes": {
                              "id": "0.0.0.100"
                            },
                            "children": [
                              {
                                "ospfv3AreaAf": {
                                  "attributes": {
                                    "cost": "16777215",
                                    "type": "ipv6-ucast"
                                  }
                                }
                              }
                            ]
                          }
                        },
                        {
                          "ospfv3DomAf": {
                            "attributes": {
                              "type": "ipv6-ucast"
                            }
                          }
                        }
                      ]
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>0.0.0.100</id>
                <areaaf-items>
                  <AreaAf-list>
                    <type>ipv6-ucast</type>
                    <cost>16777215</cost>
                  </AreaAf-list>
                </areaaf-items>
              </Area-list>
            </area-items>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
address-family ipv6 unicast
area 0.0.0.100 default-cost 16777215

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-TEST_1
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-default
ospfv3Area	sys/ospfv3/inst-TEST_1/dom-default/area-0.0.0.100
ospfv3AreaAf	sys/ospfv3/inst-TEST_1/dom-default/area-0.0.0.100/areaaf-ipv6-ucast
ospfv3DomAf	sys/ospfv3/inst-TEST_1/dom-default/af-ipv6-ucast

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters

ospfv3AreaAf Properties

Property Name	Data Type	Description	Values
cost	ospfv3:AreaCost (scalar:Uint32)	Specify cost for default inter-area-prefix LSA	RANGE: [0 , 16777215] DEFAULT: unspecified
type	ospfv3:AfT (scalar:Enum8)	Unicast IP address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

ospfv3DomAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Delete area default-cost

Delete area default-cost

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "TEST_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      },
                      "children": [
                        {
                          "ospfv3Area": {
                            "attributes": {
                              "id": "0.0.0.100"
                            },
                            "children": [
                              {
                                "ospfv3AreaAf": {
                                  "attributes": {
                                    "cost": "unspecified",
                                    "type": "ipv6-ucast"
                                  }
                                }
                              }
                            ]
                          }
                        },
                        {
                          "ospfv3DomAf": {
                            "attributes": {
                              "type": "ipv6-ucast"
                            }
                          }
                        }
                      ]
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>0.0.0.100</id>
                <areaaf-items>
                  <AreaAf-list>
                    <type>ipv6-ucast</type>
                    <cost>0</cost>
                  </AreaAf-list>
                </areaaf-items>
              </Area-list>
            </area-items>
            <af-items>
              <DomAf-list>
                <type>ipv6-ucast</type>
              </DomAf-list>
            </af-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
address-family ipv6 unicast
no area 0.0.0.100 default-cost 16777215

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-TEST_1
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-default
ospfv3Area	sys/ospfv3/inst-TEST_1/dom-default/area-0.0.0.100
ospfv3AreaAf	sys/ospfv3/inst-TEST_1/dom-default/area-0.0.0.100/areaaf-ipv6-ucast
ospfv3DomAf	sys/ospfv3/inst-TEST_1/dom-default/af-ipv6-ucast

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters

ospfv3AreaAf Properties

Property Name	Data Type	Description	Values
cost	ospfv3:AreaCost (scalar:Uint32)	Specify cost for default inter-area-prefix LSA	RANGE: [0 , 16777215] DEFAULT: unspecified
type	ospfv3:AfT (scalar:Enum8)	Unicast IP address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

ospfv3DomAf Properties

Property Name	Data Type	Description	Values
type	ospfv3:AfT (scalar:Enum8)	IPv6 unicast address family type	SELECTION: 1 - ipv6-ucast DEFAULT: ipv6-ucast

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring a VRF

Configuring a VRF

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "VRF_1"
                      }
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{

}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>VRF_1</name>
          </Dom-list>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
vrf VRF_1

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-VRF_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring a VRF

Configuring a VRF

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "VRF_1",
                        "status": "deleted"
                      }
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{

}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list nc:operation="delete">
            <name>VRF_1</name>
          </Dom-list>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
no vrf VRF_1

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-VRF_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring NSSA with route-map

Configuring NSSA with route-map

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "VRF_1"
                      },
                      "children": [
                        {
                          "ospfv3Area": {
                            "attributes": {
                              "id": "1.2.3.4",
                              "redistribute": "no",
                              "summary": "no",
                              "supressFa": "no",
                              "type": "nssa"
                            },
                            "children": [
                              {
                                "ospfv3DefRtLeakP": {
                                  "attributes": {
                                    "rtMap": "SampleString_123"
                                  }
                                }
                              }
                            ]
                          }
                        }
                      ]
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>VRF_1</name>
            <area-items>
              <Area-list>
                <id>1.2.3.4</id>
                <redistribute>false</redistribute>
                <summary>false</summary>
                <supressFa>false</supressFa>
                <type>nssa</type>
                <defrtleak-items>
                  <rtMap>SampleString_123</rtMap>
                </defrtleak-items>
              </Area-list>
            </area-items>
          </Dom-list>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
vrf VRF_1
area 1.2.3.4 nssa no-summary no-redistribution default-information-originate route-map SampleString_123

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-VRF_1
ospfv3Area	sys/ospfv3/inst-Test_1/dom-VRF_1/area-1.2.3.4
ospfv3DefRtLeakP	sys/ospfv3/inst-Test_1/dom-VRF_1/area-1.2.3.4/defrtleak
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters
redistribute	scalar:Bool	Send redistributed LSAs into NSSA area	SELECTION: true or false DEFAULT: true
summary	scalar:Bool	Originate summary LSA into other areas	SELECTION: true or false DEFAULT: true
supressFa	scalar:Bool	Supress forwarding address in translated LSA	SELECTION: true or false DEFAULT: false
type	ospfv3:AreaT (scalar:Enum8)	Configure area type as NSSA or stub	SELECTION: 1 - regular 2 - stub 3 - nssa DEFAULT: regular

ospfv3DefRtLeakP Properties

Property Name	Data Type	Description	Values
rtMap	string:Basic	The name of the default route leak policy route map. This route map name is used to control distribution.	A sequence of characters

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting NSSA with route-map

Deleting NSSA with route-map

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "VRF_1"
                      },
                      "children": [
                        {
                          "ospfv3Area": {
                            "attributes": {
                              "id": "1.2.3.4",
                              "redistribute": "yes",
                              "summary": "yes",
                              "supressFa": "no",
                              "type": "nssa"
                            },
                            "children": [
                              {
                                "ospfv3DefRtLeakP": {
                                  "attributes": {
                                    "rtMap": "SampleString_123"
                                  }
                                }
                              }
                            ]
                          }
                        }
                      ]
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>VRF_1</name>
            <area-items>
              <Area-list>
                <id>1.2.3.4</id>
                <redistribute>true</redistribute>
                <summary>true</summary>
                <supressFa>false</supressFa>
                <type>nssa</type>
                <defrtleak-items>
                  <rtMap>SampleString_123</rtMap>
                </defrtleak-items>
              </Area-list>
            </area-items>
          </Dom-list>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
vrf VRF_1
no area 1.2.3.4 nssa no-summary no-redistribution default-information-originate route-map SampleString_123

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-VRF_1
ospfv3Area	sys/ospfv3/inst-Test_1/dom-VRF_1/area-1.2.3.4
ospfv3DefRtLeakP	sys/ospfv3/inst-Test_1/dom-VRF_1/area-1.2.3.4/defrtleak
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters
redistribute	scalar:Bool	Send redistributed LSAs into NSSA area	SELECTION: true or false DEFAULT: true
summary	scalar:Bool	Originate summary LSA into other areas	SELECTION: true or false DEFAULT: true
supressFa	scalar:Bool	Supress forwarding address in translated LSA	SELECTION: true or false DEFAULT: false
type	ospfv3:AreaT (scalar:Enum8)	Configure area type as NSSA or stub	SELECTION: 1 - regular 2 - stub 3 - nssa DEFAULT: regular

ospfv3DefRtLeakP Properties

Property Name	Data Type	Description	Values
rtMap	string:Basic	The name of the default route leak policy route map. This route map name is used to control distribution.	A sequence of characters

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring discard of an External Route

Configuring discard of an External Route

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "discardRouteExt": "yes",
                        "name": "VRF_1"
                      }
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>VRF_1</name>
            <discardRouteExt>true</discardRouteExt>
          </Dom-list>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
vrf VRF_1
discard-route external

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-VRF_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
discardRouteExt	scalar:Bool	Holds the controls for discard-route external	SELECTION: true or false DEFAULT: true
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting discard of an External Route

Deleting discard of an External Route

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "discardRouteExt": "no",
                        "name": "VRF_1"
                      }
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>VRF_1</name>
            <discardRouteExt>false</discardRouteExt>
          </Dom-list>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
vrf VRF_1
no discard-route external

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-VRF_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
discardRouteExt	scalar:Bool	Holds the controls for discard-route external	SELECTION: true or false DEFAULT: true
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring an discard of Internal Route

Configuring discard of Internal Route

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "discardRouteInt": "yes",
                        "name": "VRF_1"
                      }
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>VRF_1</name>
            <discardRouteInt>true</discardRouteInt>
          </Dom-list>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
vrf VRF_1
discard-route internal

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-VRF_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
discardRouteInt	scalar:Bool	Holds the controls for discard-route internal	SELECTION: true or false DEFAULT: true
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting discard of Internal Route

Deleting discard of Internal Route

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "discardRouteInt": "no",
                        "name": "VRF_1"
                      }
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>VRF_1</name>
            <discardRouteInt>false</discardRouteInt>
          </Dom-list>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
vrf VRF_1
no discard-route internal

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-VRF_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
discardRouteInt	scalar:Bool	Holds the controls for discard-route internal	SELECTION: true or false DEFAULT: true
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring maxLsa attributes

Configuring maxLsa attributes

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "VRF_1"
                      },
                      "children": [
                        {
                          "ospfv3MaxLsaP": {
                            "attributes": {
                              "ignoreCount": "1",
                              "ignoreTime": "973",
                              "logWarning": "reject",
                              "maxLsa": "1",
                              "resetTime": "973",
                              "thresholdVal": "23"
                            }
                          }
                        }
                      ]
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>VRF_1</name>
            <maxlsa-items>
              <ignoreCount>1</ignoreCount>
              <ignoreTime>973</ignoreTime>
              <logWarning>reject</logWarning>
              <maxLsa>1</maxLsa>
              <resetTime>973</resetTime>
              <thresholdVal>23</thresholdVal>
            </maxlsa-items>
          </Dom-list>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
vrf VRF_1
max-lsa 1 23 ignore-time 973 ignore-count 1 reset-time 973

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-VRF_1
ospfv3MaxLsaP	sys/ospfv3/inst-Test_1/dom-VRF_1/maxlsa
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3MaxLsaP Properties

Property Name	Data Type	Description	Values
ignoreCount	ospf:SleepCnt (scalar:Uint32)	Set count on how many times adjacencies can be suppressed	RANGE: [1 , 4294967295] DEFAULT: 5
ignoreTime	ospf:SleepIntvl (scalar:Uint16)	Set time during which all adjacencies are suppressed	RANGE: [1 , 1440] DEFAULT: 5
logWarning	ospfv3:MaxLsaAct (scalar:Enum8)	Log a warning message when limit is exceeded	SELECTION: 0 - reject 1 - log DEFAULT: reject
maxLsa	ospf:MaxLsa (scalar:Uint32)	Set maximum number of non self-generated LSAs	RANGE: [1 , 4294967295]
resetTime	ospf:ResetIntvl (scalar:Uint32)	Set number of minutes after which ignore-count is reset to zero	RANGE: [1 , 1440] DEFAULT: 10
thresholdVal	ospf:MaxLsaThresh (scalar:Uint16)	Max LSA threshold percentage value at which to generate a warning message	RANGE: [1 , 100] DEFAULT: 75

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting maxLsa attributes

Deleting maxLsa attributes

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "VRF_1"
                      },
                      "children": [
                        {
                          "ospfv3MaxLsaP": {
                            "attributes": {
                              "status": "deleted"
                            }
                          }
                        }
                      ]
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>VRF_1</name>
            <maxlsa-items nc:operation="delete">
            </maxlsa-items>
          </Dom-list>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
vrf VRF_1
no max-lsa 1 23 ignore-time 973 ignore-count 1 reset-time 973

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-VRF_1
ospfv3MaxLsaP	sys/ospfv3/inst-Test_1/dom-VRF_1/maxlsa
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3MaxLsaP Properties

Property Name	Data Type	Description	Values
status	mo:ModificationStatus (scalar:Bitmask32)	The upgrade status. This property is for internal use only.	SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring to Log a Warning Message When max-lsa Limit is Exceeded

Configuring to Log a Warning Message When max-lsa Limit is Exceeded

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "VRF_1"
                      },
                      "children": [
                        {
                          "ospfv3MaxLsaP": {
                            "attributes": {
                              "ignoreCount": "5",
                              "ignoreTime": "5",
                              "logWarning": "log",
                              "maxLsa": "1",
                              "resetTime": "10",
                              "thresholdVal": "23"
                            }
                          }
                        }
                      ]
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>VRF_1</name>
            <maxlsa-items>
              <ignoreCount>5</ignoreCount>
              <ignoreTime>5</ignoreTime>
              <logWarning>log</logWarning>
              <maxLsa>1</maxLsa>
              <resetTime>10</resetTime>
              <thresholdVal>23</thresholdVal>
            </maxlsa-items>
          </Dom-list>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
vrf VRF_1
max-lsa 1 23 warning-only

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-VRF_1
ospfv3MaxLsaP	sys/ospfv3/inst-Test_1/dom-VRF_1/maxlsa
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3MaxLsaP Properties

Property Name	Data Type	Description	Values
ignoreCount	ospf:SleepCnt (scalar:Uint32)	Set count on how many times adjacencies can be suppressed	RANGE: [1 , 4294967295] DEFAULT: 5
ignoreTime	ospf:SleepIntvl (scalar:Uint16)	Set time during which all adjacencies are suppressed	RANGE: [1 , 1440] DEFAULT: 5
logWarning	ospfv3:MaxLsaAct (scalar:Enum8)	Log a warning message when limit is exceeded	SELECTION: 0 - reject 1 - log DEFAULT: reject
maxLsa	ospf:MaxLsa (scalar:Uint32)	Set maximum number of non self-generated LSAs	RANGE: [1 , 4294967295]
resetTime	ospf:ResetIntvl (scalar:Uint32)	Set number of minutes after which ignore-count is reset to zero	RANGE: [1 , 1440] DEFAULT: 10
thresholdVal	ospf:MaxLsaThresh (scalar:Uint16)	Max LSA threshold percentage value at which to generate a warning message	RANGE: [1 , 100] DEFAULT: 75

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting to Log a Warning Message When max-lsa Limit is Exceeded

Deleting to Log a Warning Message When max-lsa Limit is Exceeded

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "VRF_1"
                      },
                      "children": [
                        {
                          "ospfv3MaxLsaP": {
                            "attributes": {
                              "status": "deleted"
                            }
                          }
                        }
                      ]
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>VRF_1</name>
            <maxlsa-items nc:operation="delete">
            </maxlsa-items>
          </Dom-list>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
vrf VRF_1
no max-lsa 1 23 warning-only

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-VRF_1
ospfv3MaxLsaP	sys/ospfv3/inst-Test_1/dom-VRF_1/maxlsa
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3MaxLsaP Properties

Property Name	Data Type	Description	Values
status	mo:ModificationStatus (scalar:Bitmask32)	The upgrade status. This property is for internal use only.	SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Inter-Area-Prefix LSAs

Configuring Inter-Area-Prefix LSAs

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "VRF_1"
                      },
                      "children": [
                        {
                          "ospfv3MaxMetricLsaP": {
                            "attributes": {
                              "awaitConvBgpAsn": "none",
                              "externalLsa": "yes",
                              "interAreaPrefixLsa": "yes",
                              "maxMetricExtLsaValue": "11531462",
                              "maxMetricSumLsaValue": "11531462",
                              "onStartup": "yes",
                              "startupIntvl": "19270",
                              "stubPrefixLsa": "yes"
                            }
                          }
                        }
                      ]
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>VRF_1</name>
            <maxmetriclsa-items>
              <awaitConvBgpAsn>none</awaitConvBgpAsn>
              <externalLsa>true</externalLsa>
              <interAreaPrefixLsa>true</interAreaPrefixLsa>
              <maxMetricExtLsaValue>11531462</maxMetricExtLsaValue>
              <maxMetricSumLsaValue>11531462</maxMetricSumLsaValue>
              <onStartup>true</onStartup>
              <startupIntvl>19270</startupIntvl>
              <stubPrefixLsa>true</stubPrefixLsa>
            </maxmetriclsa-items>
          </Dom-list>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
vrf VRF_1
max-metric router-lsa external-lsa 11531462 stub-prefix-lsa on-startup 19270 inter-area-prefix-lsa 11531462

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-VRF_1
ospfv3MaxMetricLsaP	sys/ospfv3/inst-Test_1/dom-VRF_1/maxmetriclsa
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3MaxMetricLsaP Properties

Property Name	Data Type	Description	Values
awaitConvBgpAsn	rtleak:Asn (string:Basic)	At startup, advertise max metric until convergence of BGP ASN	A sequence of characters DEFAULT: none
externalLsa	scalar:Bool	Set this to max-metric External LSAs	SELECTION: true or false
interAreaPrefixLsa	scalar:Bool	Set this to max-metric Inter-area-prefix LSAs	SELECTION: true or false
maxMetricExtLsaValue	ospf:MaxMetric (scalar:Uint32)	Maximum metric value for external LSAs	RANGE: [0 , 16777215]
maxMetricSumLsaValue	ospf:MaxMetric (scalar:Uint32)	Maximum metric value for Inter-area-prefix/Summary LSAs	RANGE: [0 , 16777215]
onStartup	scalar:Bool	Max metric advertised should be effective only at startup	SELECTION: true or false
startupIntvl	ospf:StartupIntvl (scalar:Uint32)	Wait period in seconds after which max metric should be advertised at startup	RANGE: [5 , 86400] DEFAULT: 600
stubPrefixLsa	scalar:Bool	Advertise Max metric for Stub links as well	SELECTION: true or false

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Inter-Area-Prefix LSAs

Deleting Inter-Area-Prefix LSAs

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "VRF_1"
                      },
                      "children": [
                        {
                          "ospfv3MaxMetricLsaP": {
                            "attributes": {
                              "status": "deleted"
                            }
                          }
                        }
                      ]
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>VRF_1</name>
            <maxmetriclsa-items nc:operation="delete">
            </maxmetriclsa-items>
          </Dom-list>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
vrf VRF_1
no max-metric router-lsa external-lsa 11531462 stub-prefix-lsa on-startup 19270 inter-area-prefix-lsa 11531462

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-VRF_1
ospfv3MaxMetricLsaP	sys/ospfv3/inst-Test_1/dom-VRF_1/maxmetriclsa
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3MaxMetricLsaP Properties

Property Name	Data Type	Description	Values
status	mo:ModificationStatus (scalar:Bitmask32)	The upgrade status. This property is for internal use only.	SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Minimum Interval Between Arrival of an LSA

Configuring the Minimum Interval Between Arrival of an LSA

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "VRF_1"
                      },
                      "children": [
                        {
                          "ospfv3LsaCtrl": {
                            "attributes": {
                              "arrivalIntvl": "354408"
                            }
                          }
                        }
                      ]
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>VRF_1</name>
            <lsactrl-items>
              <arrivalIntvl>354408</arrivalIntvl>
            </lsactrl-items>
          </Dom-list>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
vrf VRF_1
timers lsa-arrival 354408

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-VRF_1
ospfv3LsaCtrl	sys/ospfv3/inst-Test_1/dom-VRF_1/lsactrl
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3LsaCtrl Properties

Property Name	Data Type	Description	Values
arrivalIntvl	ospfv3:LsaArrivalIntvl (scalar:Uint32)	Minimum interval between arrival of a LSA	RANGE: [10 , 600000] DEFAULT: 1000

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting the Minimum Interval Between Arrival of an LSA

Deleting the Minimum Interval Between Arrival of an LSA

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "Test_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "VRF_1"
                      },
                      "children": [
                        {
                          "ospfv3LsaCtrl": {
                            "attributes": {
                              "arrivalIntvl": "1000"
                            }
                          }
                        }
                      ]
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>Test_1</name>
        <dom-items>
          <Dom-list>
            <name>VRF_1</name>
            <lsactrl-items>
              <arrivalIntvl>1000</arrivalIntvl>
            </lsactrl-items>
          </Dom-list>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 Test_1
vrf VRF_1
no timers lsa-arrival 354408

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-Test_1
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-VRF_1
ospfv3LsaCtrl	sys/ospfv3/inst-Test_1/dom-VRF_1/lsactrl
ospfv3Dom	sys/ospfv3/inst-Test_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3LsaCtrl Properties

Property Name	Data Type	Description	Values
arrivalIntvl	ospfv3:LsaArrivalIntvl (scalar:Uint32)	Minimum interval between arrival of a LSA	RANGE: [10 , 600000] DEFAULT: 1000

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configure authentication disable on a virtual link

Configure authentication disable on a virtual link

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "TEST_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3Area": {
                      "attributes": {
                        "id": "3.3.3.3"
                      },
                      "children": [
                        {
                          "ospfv3Vlink": {
                            "attributes": {
                              "nbrRtrId": "10.10.10.10"
                            },
                            "children": [
                              {
                                "ospfv3VlinkAuthNewP": {
                                  "attributes": {
                                    "authType": "disable"
}}}]}}]}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>3.3.3.3</id>
                <vlink-items>
                  <Vlink-list>
                    <nbrRtrId>10.10.10.10</nbrRtrId>
                    <auth-items>
                      <authType>disable</authType>
                    </auth-items>
                  </Vlink-list>
                </vlink-items>
              </Area-list>
            </area-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
area 3.3.3.3 virtual-link 10.10.10.10
authentication disable

Verifying a DME Configuration

MO	DN
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-TEST_1
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-default
ospfv3Area	sys/ospfv3/inst-TEST_1/dom-default/area-3.3.3.3
ospfv3Vlink	sys/ospfv3/inst-TEST_1/dom-default/area-3.3.3.3/vlink-10.10.10.10
ospfv3VlinkAuthNewP	sys/ospfv3/inst-TEST_1/dom-default/area-3.3.3.3/vlink-10.10.10.10/auth

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3Area Properties

Property Name	Data Type	Description	Values
id	ospfv3:AreaId (string:Basic)	Area Id as an integer or ip address	A sequence of characters

ospfv3Vlink Properties

The following table contains information about the ospfv3Vlink properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
nbrRtrId	ip:RtrId (address:IPv4)	Router id associated with virtual link neighbor	Value must match ipv4 format

ospfv3VlinkAuthNewP Properties

The following table contains information about the ospfv3VlinkAuthNewP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
authType	ospfv3:AuthType (scalar:Enum8)	Authentication types which can be md5, sha1 or disable.	SELECTION: 0 - none 1 - md5 2 - sha1 3 - disable

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Delete authentication disable on a virtual link

Delete authentication disable on a virtual link

POST http://<mgmt0_IP>/api/mo/sys/ospfv3.json

{
  "ospfv3Entity": {
    "children": [
      {
        "ospfv3Inst": {
          "attributes": {
            "name": "TEST_1"
          },
          "children": [
            {
              "ospfv3Dom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "ospfv3Area": {
                      "attributes": {
                        "id": "3.3.3.3"
                      },
                      "children": [
                        {
                          "ospfv3Vlink": {
                            "attributes": {
                              "nbrRtrId": "10.10.10.10"
                            },
                            "children": [
                              {
                                "ospfv3VlinkAuthNewP": {
                                  "attributes": {
                                    "authType": "disable"
}}}]}}]}}]}}]}}]}}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>default</name>
            <area-items>
              <Area-list>
                <id>3.3.3.3</id>
                <vlink-items>
                  <Vlink-list>
                    <nbrRtrId>10.10.10.10</nbrRtrId>
                    <auth-items>
                      <authType>disable</authType>
                    </auth-items>
                  </Vlink-list>
                </vlink-items>
              </Area-list>
            </area-items>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
area 3.3.3.3 virtual-link 10.10.10.10
no authentication disable

Configure timers throttle lsa start-time hold-time max-time

Configure timers throttle lsa start-time hold-time max-time

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "TEST_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "abcdefghijklmnopqrst"
                      },
                      "children": [
                        {
                          "ospfv3LsaCtrl": {
                            "attributes": {
                              "holdIntvl": "30000",
                              "maxIntvl": "30000",
                              "startIntvl": "5000"
                            }
                          }
                        }
                      ]
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>abcdefghijklmnopqrst</name>
            <lsactrl-items>
              <holdIntvl>30000</holdIntvl>
              <maxIntvl>30000</maxIntvl>
              <startIntvl>5000</startIntvl>
            </lsactrl-items>
          </Dom-list>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
vrf abcdefghijklmnopqrst
timers throttle lsa 5000 30000 30000

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-TEST_1
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-abcdefghijklmnopqrst
ospfv3LsaCtrl	sys/ospfv3/inst-TEST_1/dom-abcdefghijklmnopqrst/lsactrl
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3LsaCtrl Properties

Property Name	Data Type	Description	Values
holdIntvl	ospfv3:LsaThHoldIntvl (scalar:Uint32)	LSA generation throttle hold interval	RANGE: [50 , 30000] DEFAULT: 5000
maxIntvl	ospfv3:LsaThMaxIntvl (scalar:Uint32)	LSA generation throttle maximum interval	RANGE: [50 , 30000] DEFAULT: 5000
startIntvl	ospfv3:LsaThStartIntvl (scalar:Uint32)	LSA generation throttle start wait interval	RANGE: [0 , 5000] DEFAULT: 0

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Delete timers throttle lsa start-time hold-time max-time

Delete timers throttle lsa start-time hold-time max-time

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "TEST_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "abcdefghijklmnopqrst"
                      },
                      "children": [
                        {
                          "ospfv3LsaCtrl": {
                            "attributes": {
                              "holdIntvl": "5000",
                              "maxIntvl": "5000",
                              "startIntvl": "0"
                            }
                          }
                        }
                      ]
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>abcdefghijklmnopqrst</name>
            <lsactrl-items>
              <holdIntvl>5000</holdIntvl>
              <maxIntvl>5000</maxIntvl>
              <startIntvl>0</startIntvl>
            </lsactrl-items>
          </Dom-list>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
vrf abcdefghijklmnopqrst
no timers throttle lsa 5000 30000 30000

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-TEST_1
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-abcdefghijklmnopqrst
ospfv3LsaCtrl	sys/ospfv3/inst-TEST_1/dom-abcdefghijklmnopqrst/lsactrl
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3LsaCtrl Properties

Property Name	Data Type	Description	Values
holdIntvl	ospfv3:LsaThHoldIntvl (scalar:Uint32)	LSA generation throttle hold interval	RANGE: [50 , 30000] DEFAULT: 5000
maxIntvl	ospfv3:LsaThMaxIntvl (scalar:Uint32)	LSA generation throttle maximum interval	RANGE: [50 , 30000] DEFAULT: 5000
startIntvl	ospfv3:LsaThStartIntvl (scalar:Uint32)	LSA generation throttle start wait interval	RANGE: [0 , 5000] DEFAULT: 0

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configure timers lsa-group-pacing interval

Configure timers lsa-group-pacing interval

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "TEST_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "abcdefghijklmnopqrst"
                      },
                      "children": [
                        {
                          "ospfv3LsaCtrl": {
                            "attributes": {
                              "gpPacingIntvl": "1800"
                            }
                          }
                        }
                      ]
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>abcdefghijklmnopqrst</name>
            <lsactrl-items>
              <gpPacingIntvl>1800</gpPacingIntvl>
            </lsactrl-items>
          </Dom-list>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
vrf abcdefghijklmnopqrst
timers lsa-group-pacing 1800

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-TEST_1
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-abcdefghijklmnopqrst
ospfv3LsaCtrl	sys/ospfv3/inst-TEST_1/dom-abcdefghijklmnopqrst/lsactrl
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3LsaCtrl Properties

Property Name	Data Type	Description	Values
gpPacingIntvl	ospfv3:LsaGpPacingIntvl (scalar:Uint16)	LSA group pacing interval	RANGE: [1 , 1800] DEFAULT: 10

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Delete timers lsa-group-pacing interval

Delete timers lsa-group-pacing interval

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "ospfv3Entity": {
          "children": [
            {
              "ospfv3Inst": {
                "attributes": {
                  "name": "TEST_1"
                },
                "children": [
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "abcdefghijklmnopqrst"
                      },
                      "children": [
                        {
                          "ospfv3LsaCtrl": {
                            "attributes": {
                              "gpPacingIntvl": "10"
                            }
                          }
                        }
                      ]
                    }
                  },
                  {
                    "ospfv3Dom": {
                      "attributes": {
                        "name": "default"
                      }
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    
}

<System>
  <ospfv3-items>
    <inst-items>
      <Inst-list>
        <name>TEST_1</name>
        <dom-items>
          <Dom-list>
            <name>abcdefghijklmnopqrst</name>
            <lsactrl-items>
              <gpPacingIntvl>10</gpPacingIntvl>
            </lsactrl-items>
          </Dom-list>
          <Dom-list>
            <name>default</name>
          </Dom-list>
        </dom-items>
      </Inst-list>
    </inst-items>
  </ospfv3-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

router ospfv3 TEST_1
vrf abcdefghijklmnopqrst
no timers lsa-group-pacing 1800

Verifying a DME Configuration

MO	DN
topSystem	sys
ospfv3Entity	sys/ospfv3
ospfv3Inst	sys/ospfv3/inst-TEST_1
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-abcdefghijklmnopqrst
ospfv3LsaCtrl	sys/ospfv3/inst-TEST_1/dom-abcdefghijklmnopqrst/lsactrl
ospfv3Dom	sys/ospfv3/inst-TEST_1/dom-default

ospfv3Inst Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 128

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

ospfv3LsaCtrl Properties

Property Name	Data Type	Description	Values
gpPacingIntvl	ospfv3:LsaGpPacingIntvl (scalar:Uint16)	LSA group pacing interval	RANGE: [1 , 1800] DEFAULT: 10

ospfv3Dom Properties

Property Name	Data Type	Description	Values
name	naming:Name256 (string:Basic)	The name of the object.	MAX SIZE: 63

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html