Configuring the Quality Level to be Transmitted (Lowest)

Configuring ITU-T Option 1: Primary Reference Clock

Configuring ITU-T Option 1: Primary Reference Clock

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "fsyncMgrSynceEntity": {
          "children": [
            {
              "fsyncMgrSynceEthif": {
                "attributes": {
                  "freqsync": "yes",
                  "id": "eth1/3",
                  "qltxexactoptype": "op1",
                  "qltxexactval": "fsync-ql-common-none",
                  "qltxhval": "fsync-ql-o1-sec",
                  "qltxlval": "fsync-ql-o1-prc"
                }
              }
            }
          ]
        }
      },
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/3"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <fsyncmgr-items>
    <if-items>
      <MgrSynceEthif-list>
        <id>eth1/3</id>
        <freqsync>true</freqsync>
        <qltxexactoptype>op1</qltxexactoptype>
        <qltxexactval>fsync-ql-common-none</qltxexactval>
        <qltxhval>fsync-ql-o1-sec</qltxhval>
        <qltxlval>fsync-ql-o1-prc</qltxlval>
      </MgrSynceEthif-list>
    </if-items>
  </fsyncmgr-items>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/3</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

interface ethernet 1/3
  frequency synchronization
   quality transmit lowest itu-t option 1 PRC highest SEC

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

fsyncMgrSynceEthif Properties

The following table contains information about the fsyncMgrSynceEthif properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

l1PhysIf Properties

The following table contains information about the l1PhysIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting ITU-T Option 1: Primary Reference Clock

Deleting ITU-T Option 1: Primary Reference Clock

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "fsyncMgrSynceEntity": {
          "children": [
            {
              "fsyncMgrSynceEthif": {
                "attributes": {
                  "freqsync": "yes",
                  "id": "eth1/3",
                  "qltxexactoptype": "none",
                  "qltxexactval": "fsync-ql-common-none",
                  "qltxhval": "fsync-ql-common-none",
                  "qltxlval": "fsync-ql-common-none"
                }
              }
            }
          ]
        }
      },
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/3"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <fsyncmgr-items>
    <if-items>
      <MgrSynceEthif-list>
        <id>eth1/3</id>
        <freqsync>true</freqsync>
        <qltxexactoptype>none</qltxexactoptype>
        <qltxexactval>fsync-ql-common-none</qltxexactval>
        <qltxhval>fsync-ql-common-none</qltxhval>
        <qltxlval>fsync-ql-common-none</qltxlval>
      </MgrSynceEthif-list>
    </if-items>
  </fsyncmgr-items>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/3</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

interface ethernet 1/3
  frequency synchronization
   no quality transmit lowest itu-t option 1 PRC highest SEC

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

fsyncMgrSynceEthif Properties

The following table contains information about the fsyncMgrSynceEthif properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

l1PhysIf Properties

The following table contains information about the l1PhysIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring ITU-T Option 2, Generation 1: Stratum 3

Configuring ITU-T Option 2, Generation 1: Stratum 3

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "fsyncMgrSynceEntity": {
          "children": [
            {
              "fsyncMgrSynceEthif": {
                "attributes": {
                  "freqsync": "yes",
                  "id": "eth1/3",
                  "qltxexactoptype": "op2g1",
                  "qltxexactval": "fsync-ql-common-none",
                  "qltxhval": "fsync-ql-o2-g1-stu",
                  "qltxlval": "fsync-ql-o2-g1-st3"
                }
              }
            }
          ]
        }
      },
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/3"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <fsyncmgr-items>
    <if-items>
      <MgrSynceEthif-list>
        <id>eth1/3</id>
        <freqsync>true</freqsync>
        <qltxexactoptype>op2g1</qltxexactoptype>
        <qltxexactval>fsync-ql-common-none</qltxexactval>
        <qltxhval>fsync-ql-o2-g1-stu</qltxhval>
        <qltxlval>fsync-ql-o2-g1-st3</qltxlval>
      </MgrSynceEthif-list>
    </if-items>
  </fsyncmgr-items>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/3</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

interface ethernet 1/3
  frequency synchronization
   quality transmit lowest itu-t option 2 generation 1 ST3 highest STU

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

fsyncMgrSynceEthif Properties

The following table contains information about the fsyncMgrSynceEthif properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

l1PhysIf Properties

The following table contains information about the l1PhysIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting ITU-T Option 2, Generation 1: Stratum 3

Deleting ITU-T Option 2, Generation 1: Stratum 3

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "fsyncMgrSynceEntity": {
          "children": [
            {
              "fsyncMgrSynceEthif": {
                "attributes": {
                  "freqsync": "yes",
                  "id": "eth1/3",
                  "qltxexactoptype": "none",
                  "qltxexactval": "fsync-ql-common-none",
                  "qltxhval": "fsync-ql-common-none",
                  "qltxlval": "fsync-ql-common-none"
                }
              }
            }
          ]
        }
      },
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/3"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <fsyncmgr-items>
    <if-items>
      <MgrSynceEthif-list>
        <id>eth1/3</id>
        <freqsync>true</freqsync>
        <qltxexactoptype>none</qltxexactoptype>
        <qltxexactval>fsync-ql-common-none</qltxexactval>
        <qltxhval>fsync-ql-common-none</qltxhval>
        <qltxlval>fsync-ql-common-none</qltxlval>
      </MgrSynceEthif-list>
    </if-items>
  </fsyncmgr-items>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/3</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

interface ethernet 1/3
  frequency synchronization
   no quality transmit lowest itu-t option 2 generation 1 ST3 highest STU

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

fsyncMgrSynceEthif Properties

The following table contains information about the fsyncMgrSynceEthif properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

l1PhysIf Properties

The following table contains information about the l1PhysIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring ITU-T Option 1: Enhanced Primary Reference Timing Clock

Configuring ITU-T Option 1: Enhanced Primary Reference Timing Clock

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "fsyncMgrSynceEntity": {
          "children": [
            {
              "fsyncMgrSynceEthif": {
                "attributes": {
                  "freqsync": "yes",
                  "id": "eth1/3",
                  "qltxexactoptype": "op2g2",
                  "qltxexactval": "fsync-ql-common-none",
                  "qltxhval": "fsync-ql-o2-g2-tnc",
                  "qltxlval": "fsync-ql-o2-g2-eprtc"
                }
              }
            }
          ]
        }
      },
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/3"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <fsyncmgr-items>
    <if-items>
      <MgrSynceEthif-list>
        <id>eth1/3</id>
        <freqsync>true</freqsync>
        <qltxexactoptype>op2g2</qltxexactoptype>
        <qltxexactval>fsync-ql-common-none</qltxexactval>
        <qltxhval>fsync-ql-o2-g2-tnc</qltxhval>
        <qltxlval>fsync-ql-o2-g2-eprtc</qltxlval>
      </MgrSynceEthif-list>
    </if-items>
  </fsyncmgr-items>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/3</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

interface ethernet 1/3
  frequency synchronization
   quality transmit lowest itu-t option 2 generation 2 ePRTC highest TNC

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

fsyncMgrSynceEthif Properties

The following table contains information about the fsyncMgrSynceEthif properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

l1PhysIf Properties

The following table contains information about the l1PhysIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting ITU-T Option 1: Enhanced Primary Reference Timing Clock

Deleting ITU-T Option 1: Enhanced Primary Reference Timing Clock

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "fsyncMgrSynceEntity": {
          "children": [
            {
              "fsyncMgrSynceEthif": {
                "attributes": {
                  "freqsync": "yes",
                  "id": "eth1/3",
                  "qltxexactoptype": "none",
                  "qltxexactval": "fsync-ql-common-none",
                  "qltxhval": "fsync-ql-common-none",
                  "qltxlval": "fsync-ql-common-none"
                }
              }
            }
          ]
        }
      },
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/3"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <fsyncmgr-items>
    <if-items>
      <MgrSynceEthif-list>
        <id>eth1/3</id>
        <freqsync>true</freqsync>
        <qltxexactoptype>none</qltxexactoptype>
        <qltxexactval>fsync-ql-common-none</qltxexactval>
        <qltxhval>fsync-ql-common-none</qltxhval>
        <qltxlval>fsync-ql-common-none</qltxlval>
      </MgrSynceEthif-list>
    </if-items>
  </fsyncmgr-items>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/3</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

interface ethernet 1/3
  frequency synchronization
   no quality transmit lowest itu-t option 2 generation 2 ePRTC highest TNC

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

fsyncMgrSynceEthif Properties

The following table contains information about the fsyncMgrSynceEthif properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

l1PhysIf Properties

The following table contains information about the l1PhysIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting the Quality Level to be Transmitted

Deleting the Quality Level to be Transmitted 

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "fsyncMgrSynceEntity": {
          "children": [
            {
              "fsyncMgrSynceEthif": {
                "attributes": {
                  "freqsync": "yes",
                  "id": "eth1/3",
                  "qltxexactoptype": "none",
                  "qltxexactval": "fsync-ql-common-none",
                  "qltxhval": "fsync-ql-common-none",
                  "qltxlval": "fsync-ql-common-none"
                }
              }
            }
          ]
        }
      },
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/3"
                }
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <fsyncmgr-items>
    <if-items>
      <MgrSynceEthif-list>
        <id>eth1/3</id>
        <freqsync>true</freqsync>
        <qltxexactoptype>none</qltxexactoptype>
        <qltxexactval>fsync-ql-common-none</qltxexactval>
        <qltxhval>fsync-ql-common-none</qltxhval>
        <qltxlval>fsync-ql-common-none</qltxlval>
      </MgrSynceEthif-list>
    </if-items>
  </fsyncmgr-items>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/3</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
</System>

Note: This example was added in Release 9.3(5).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

interface ethernet 1/3
  frequency synchronization
   no quality transmit

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

fsyncMgrSynceEthif Properties

The following table contains information about the fsyncMgrSynceEthif properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

l1PhysIf Properties

The following table contains information about the l1PhysIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html