Cisco Nexus 3000 and 9000 Series NX-API REST SDK API, Release 9.3(x)

NX-OS 9.3(x)

Cisco Nexus 3000 and 9000 Series NX-API REST Documentation

Querying the Module Temperature Sensor Data

DME

Copy
GET http://<IP_Address>/api/mo/sys/ch/supslot-1/sup/sensor-1.json
{
  "eqptSensor": {
    "attributes": {
      "childAction": "",
      "descr": "FRONT",
      "dn": "sys/ch/supslot-1/sup/sensor-1",
      "id": "1",
      "majorThresh": "70",
      "mfgTm": "not-applicable",
      "minorThresh": "42",
      "modTs": "2017-06-06T22:11:05.299+00:00",
      "model": "FRONT",
      "monPolDn": "",
      "operSt": "normal",
      "persistentOnReload": "false",
      "rev": "n/a",
      "ser": "n/a",
      "status": "",
      "tempValue": "25",
      "type": "inlet",
      "unit": "Celsius",
      "vendor": "Cisco Systems"
    }
  }
}

Environmental Monitoring

Querying the Module Temperature Sensor Data

Provides sensor data for environmental monitors such as temperature gauges.

CLI Commands

The DME payload is the equivalent of the sensor name (descr), MajorThresh (majorThresh), MinorThres (minorThresh), CurTemp (tempValue), status (operSt), and the temperature scale (unit) given in the first row of the show environment temperature module module output table. Compare the payload with the CLI Output.

CLI Output
switch# show environment temperature module 1 Temperature: ----------------------------------------------------------------------- Module Sensor MajorThresh MinorThres CurTemp Status (Celsius) (Celsius) (Celsius) ----------------------------------------------------------------------- 1 FRONT 70 42 25 Ok 1 BACK 80 70 33 Ok 1 CPU 95 80 34 Ok 1 TH 105 90 50 Ok 1 VRM-1 110 100 50 Ok

CLI Output

 switch# show environment temperature module 1    
 Temperature:    
 -----------------------------------------------------------------------    
 Module   Sensor      MajorThresh      MinorThres   CurTemp   Status	  
                        (Celsius)     (Celsius)  (Celsius)    
 ----------------------------------------------------------------------- 
 1       FRONT          70               42          25         Ok   
 1       BACK           80               70          33         Ok    
 1       CPU            95               80          34         Ok    
 1       TH             105              90          50         Ok    
 1       VRM-1          110              100         50         Ok

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

MO	DN
eqptSensor	sys/ch/supslot-{id}/sup/sensor-{id}

eqptSensor Properties

The following table contains information about the eqptSensor properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
childAction	mo:ModificationChildAction scalar:Bitmask32	Delete or ignore. For internal use only.	SELECTION: 16384u - deleteAll 4096u - ignore 8192u - deleteNonPresent DEFAULT: 0
descr	eqpt:Descr	Description of the specified attribute
dn	reference:BinRef	A tag or metadata is a non-hierarchical keyword or term assigned to the fabric module.
id	eqpt:Id (scalar:Uint32)	The item identifier.	RANGE: [1 , 32]
majorThresh	eqpt:TempThresh (scalar:Sint16)	The major threshold of the sensor.	RANGE: [-32768 , 32767]
mfgTm	scalar:Date	The manufacturing time.	SELECTION: 0ull - not-applicable DEFAULT: not-applicable(0ull)
minorThresh	eqpt:TempThresh (scalar:Sint16)	The minor threshold of the sensor.	RANGE: [-32768 , 32767]
modTs	mo:TStamp (scalar:Date)	The time when this object was last modified.	SELECTION: 0 - never DEFAULT: never
model	eqpt:Model (string:Basic)	Model	A sequence of characters
monPolDn	reference:BinRef	The monitoring policy attached to this observable object.
operSt	eqpt:SensorOpSt (scalar:Enum8)	The runtime state.	SELECTION: 0 - fail 1 - normal 2 - minor 3 - major 4 - absent 5 - bad-asic DEFAULT: absent
persistentOnReload	mo:Persistent scalar:Enum8	NO COMMENTS	SELECTION: 0 - false 1 - true DEFAULT: true(1)
rev	eqpt:Revision string:Basic	The revision number.	RANGE: Min: "0" Max: "512" DEFAULT: "0"
ser	eqpt:Serial string:Basic	The serial number.	RANGE: Min: "0" Max: "16"
status	mo:ModificationStatus (scalar:Bitmask32)	The upgrade status. This property is for internal use only.	SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced
tempValue	eqpt:TempValue (scalar:Uint16)	The equipment sensor temperature value	RANGE: [0, 65535] DEFAULT: 0
type	eqpt:SensorT (scalar:Enum8)	The type of sensor.	SELECTION: 1 - cpu 2 - inlet 3 - outlet 4 - hotswap 5 - dimm 6 - phy 7 - sfp 8 - qsfp 9 - asic 10 - pch 11 - cpu-crm 12 - asic-vrm 18 - x86 19 - arm 20 - die DEFAULT: asic
unit	string:Basic	The equipment sensor temperature unit	A sequence of characters
vendor	eqpt:Vendor (string:Basic)	Vendor	A sequence of characters DEFAULT: Cisco Systems, Inc

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Querying the Power Supply Data

Provides system inventory power supply information.

CLI Commands

The DME payload provides information on PID (model), VID (hwVer), and SN (ser) numbers given in the show inventory power_supply output and provides the voltage (volt), ampere input (drawnCurr), and status (operSt) given in the show environment power ampere output. Compare the payload with the CLI Output.

CLI Output
switch# show inventory power_supply NAME: "Power Supply 1", DESCR:"Nexus3000 C3232C Chassis Power Supply" PID: NXA-PAC-650W-PI , VID: V01 , SN: LIT192818FC

CLI Output
switch# show environment power ampere Power Supply: Voltage: 12 Volts Power Actual Actual Total Supply Model Output Input Capacity Status (Ampere) (Ampere) (Ampere) ------- ------------------- ---------- ---------- ---------- ------------ 1 NXA-PAC-650W-PI 6.58 A 0.42 A 54.16 A Ok 2 NXA-PAC-650W-PI 5.92 A 0.39 A 54.16 A Ok

CLI Output

 switch# show environment power ampere      
 Power Supply:    
 Voltage: 12 Volts    
 Power                             Actual      Actual        Total    
 Supply    Model                  Output      Input      Capacity    Status    
                                (Ampere)    (Ampere)     (Ampere)    
 -------  -------------------  ----------  ----------  ----------  ------------   	  
 1        NXA-PAC-650W-PI 
 6.58 A   0.42 A    54.16 A     Ok        
 2        NXA-PAC-650W-PI        5.92 A   0.39 A    54.16 A     Ok

Note: The property information for this example was added in Release 9.3(3).

MO	DN
eqptPsu	sys/ch/psuslot-{id}/psu

eqptPsu Properties

The following table contains information about the eqptPsu properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
almReg	scalar:Uint16	The power supply alarm register.
cap	eqpt:Amps (scalar:Float)	The power supply capacity in milli amps.	A floating number per IEEE-754 standard
childAction	mo:ModificationChildAction scalar:Bitmask32	Delete or ignore. For internal use only.	SELECTION: 16384u - deleteAll 4096u - ignore 8192u - deleteNonPresent DEFAULT: 0
descr	eqpt:Descr	Description of the specified attribute
dn	reference:BinRef	A tag or metadata is a non-hierarchical keyword or term assigned to the fabric module.
drawnCurr	eqpt:Amps (scalar:Float)	The power supply unit actual drawn/output current	A floating number per IEEE-754 standard
fanOpSt	eqpt:OpSt (scalar:Enum8)	The power supply fan's operational status.	SELECTION: 0 - unknown 1 - ok 2 - fail 3 - absent 4 - shut 5 - mismatch DEFAULT: unknown
hwVer	cap:Version (string:Basic)	The hardware version of a card.	A sequence of characters
id	eqpt:Id (scalar:Uint32)	The item identifier.	RANGE: [0, 4294967295]
mfgTm	scalar:Date	Manufacturing Time	DATE FORMAT: %Y-%m-%dT%H:%M:%S.%f%z DEFAULT: not-applicable
modTs	mo:TStamp (scalar:Date)	The time when this object was last modified.	SELECTION: 0 - never DEFAULT: never
model	eqpt:Model (string:Basic)	Model	A sequence of characters
monPolDn	reference:BinRef	The monitoring policy associated with the power supply.
operSt	eqpt:OpSt (scalar:Enum8)	The power supply status.	SELECTION: 0 - unknown 1 - ok 2 - fail 3 - absent 4 - shut 5 - mismatch DEFAULT: unknown
persistentOnReload	mo:Persistent scalar:Enum8	NO COMMENTS	SELECTION: 0 - false 1 - true DEFAULT: true(1)
rev	eqpt:Revision (string:Basic)	Revision	A sequence of characters DEFAULT: 0
ser	eqpt:Serial (naming:Name)	Serial Number	MAX SIZE: 16
status	mo:ModificationStatus (scalar:Bitmask32)	The upgrade status. This property is for internal use only.	SELECTION: 2 - created 4 - modified 8 - deleted 16 - replaced
vSrc	eqpt:VSrc (scalar:Enum8)	The power supply voltage source.	SELECTION: 0 - unknown 1 - 110v 2 - 220v DEFAULT: unknown
vendor	eqpt:Vendor (string:Basic)	Vendor	A sequence of characters DEFAULT: Cisco Systems, Inc
volt	eqpt:Volts (scalar:Float)	The power supply voltage.	A floating number per IEEE-754 standard

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Querying the Transceiver Data

Provides transceiver interface information.

CLI Commands

The DME payload provides the slot and port numbers (dn: sys/intf/phys-{[id]}...), interface name (guiName), part number (guiPN), serial number (guiSN), link length (distIn10mFor50u), and the Cisco extended ID number (xcvrExtId) given in the show interface ethernet slot/port transceiver output. Compare the payload with the CLI Output.

CLI Output
switch# show interface e2/2 transceiver Ethernet2/2 transceiver is present type is QSFP-40G-SR4 name is CISCO part number is AFBR-79EIPZ-CS1 revision is 02 serial number is AVP1606S381 nominal bitrate is 10300 MBit/sec per channel Link length supported for 50/125um OM2 fiber is 30 m Link length supported for 50/125um OM3 fiber is 100 m cisco id is 13 cisco extended id number is 16

CLI Output

 switch# show interface e2/2 transceiver    
 Ethernet2/2    
 transceiver is present    
 type is QSFP-40G-SR4    
 name is CISCO    
 part number is AFBR-79EIPZ-CS1    
 revision is 02    
 serial number is AVP1606S381    
 nominal bitrate is 10300 MBit/sec per channel    
 Link length supported for 50/125um OM2 fiber is 30 m    
 Link length supported for 50/125um OM3 fiber is 100 m    
 cisco id is 13    
 cisco extended id number is 16

Note: The property information for this example was added in Release 9.3(3).

MO	DN
ethpmFcot	sys/intf/phys-{[id]}/phys/fcot

ethpmFcot Properties

The following table contains information about the ethpmFcot properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
baseResvd1	scalar:UByte	Base Reserved Field	RANGE: [0, 255]
baseResvd2	scalar:UByte	Base Reserved Field	RANGE: [0, 255]
baseResvd3	scalar:UByte	Base Reserved Field	RANGE: [0, 255]
baseResvd4	ethpm:SfpReserved4Array (base:Uint8Array)	Base Reserved Field	ARRAY SIZE: 3
brIn100MHz	scalar:UByte	Baud Rate	RANGE: [0, 255]
brMaxMargin	scalar:UByte	Baud Rate Maximum Margin	RANGE: [0, 255]
brMinMargin	scalar:UByte	Baud Rate Minimum Margin	RANGE: [0, 255]
ccex	scalar:UByte	RANGE: [0, 255]
ccid	scalar:UByte	CCID	RANGE: [0, 255]
connectType	scalar:UByte	Connector Type	RANGE: [0, 255]
dateCode	string:Basic	The vendor?s manufacturing date code.	A sequence of characters
description	string:Basic	Fcot description	A sequence of characters
diagMonType	scalar:UByte	RANGE: [0, 255]
distIn100mFor9u	scalar:UByte	Distance	RANGE: [0, 255]
distIn10mFor50u	scalar:UByte	Distance	RANGE: [0, 255]
distIn10mFor60u	scalar:UByte	Distance	RANGE: [0, 255]
distIn1mForCu	scalar:UByte	Distance	RANGE: [0, 255]
distInKmFor9u	scalar:UByte	Distance	RANGE: [0, 255]
dn	reference:BinRef	A tag or metadata is a non-hierarchical keyword or term assigned to the fabric module.
encoding	scalar:UByte	Encoding	RANGE: [0, 255]
enhOption	scalar:UByte	RANGE: [0, 255]
extOption	ethpm:SfpExtendedOptionBytes (base:Uint8Array)	Extended Option	ARRAY SIZE: 2
fCTxType	scalar:UByte	The type of fibre channel transmitter.	RANGE: [0, 255]
fcotNum	scalar:UByte	The FCOT number. The device number that this info belongs to.	RANGE: [0, 255]
fcotStatus	scalar:UByte	Fcot status	RANGE: [0, 255]
fcotType	scalar:UByte	The transceiver type. This property is a numerical value.	RANGE: [0, 255]
flags	ethpm:FcotFlags (scalar:Enum8)	Fcot flags	SELECTION: 0 - unknown 1 - access-failed 2 - checksum-failed 3 - vendor-crc-failed 4 - sfp-speed-mismatch 5 - eth-compalint-failed 6 - unknown-xcvr-type 7 - emphasis-checksum-failed 8 - init-failed 9 - ok-auth-success-no-md5 10 - auth-failed 11 - ok-delayed-auth-success 12 - delayed-auth-failed 13 - ok-no-md5 14 - ok DEFAULT: unknown
gigEthCC	scalar:UByte	RANGE: [0, 255]
guiCiscoEID	NA	NA	NA
guiCiscoPID	NA	NA	NA
guiCiscoPN	NA	NA	NA
guiName	NA	NA	NA
guiPN	NA	NA	NA
guiRev	NA	NA	NA
guiSN	NA	NA	NA
isFcotPresent	scalar:Bool	Fcot presence status	SELECTION: true or false
maxSpeed	scalar:Uint32	The nominal bitrate in MBits per sec.	RANGE: [0, 4294967295]
minSpeed	scalar:Uint32	The minimum speed of the interface.	RANGE: [0, 4294967295]
partNumber	string:Basic	Fcot part number	A sequence of characters
sff8472Compl	scalar:UByte	RANGE: [0, 255]
state	ethpm:FcotState (scalar:Enum8)	Fcot state	SELECTION: 0 - unknown 1 - inserted 2 - removed 3 - hw-failure 4 - inserted-initializing DEFAULT: unknown
type	ethpm:FcotType (scalar:Enum8)	Fcot type	SELECTION: 0 - unknown 1 - xfp 2 - x2 3 - dummy 4 - sfp 5 - qsfp 6 - cfp-40g 7 - cfp-100g 8 - cfp 9 - qsfp28 10 - qsfpdd 11 - cpak 12 - qsfp56 13 - cxp DEFAULT: unknown
typeName	string:Basic	Type Name	A sequence of characters
vendorData	ethpm:X2VendorDataBytes (base:Uint8Array)	ARRAY SIZE: 32
vendorId	ethpm:SfpVendorIdBytes (base:Uint8Array)	Vendor ID	ARRAY SIZE: 3
vendorName	string:Basic	Vendor Name	A sequence of characters
vendorPn	string:Basic	Vendor Part Number	A sequence of characters
vendorRev	string:Basic	Vendor Revision	A sequence of characters
vendorSn	string:Basic	A sequence of characters
versionId	string:Basic	Fcot version id	A sequence of characters
xcvrCode	ethpm:SfpXcvrCodeBytes (base:Uint8Array)	Transceiver Code	ARRAY SIZE: 8
xcvrExtId	scalar:UByte	Transceiver Extended ID	RANGE: [0, 255]
xcvrId	scalar:UByte	Transceiver ID	RANGE: [0, 255]

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Querying the Transceiver Sensor Data

Provides transceiver sensor information.

CLI Commands

The DME payload provides the lane number and voltage (description), curent measurement (value), alarms (highAlarm and lowAlarm), warnings (highWarning and lowWarning), and the sensor unit (unit) given in the show interface ethernet slot/port transceiver output. Compare the payload with the CLI Output.

CLI Output
switch# show interface e2/2 transceiver details Ethernet2/2 transceiver is present type is QSFP-40G-SR4 name is CISCO part number is AFBR-79EIPZ-CS1 revision is 02 serial number is AVP1606S381 nominal bitrate is 10300 MBit/sec per channel Link length supported for 50/125um OM2 fiber is 30 m Link length supported for 50/125um OM3 fiber is 100 m cisco id is 13 cisco extended id number is 16

CLI Output

 switch# show interface e2/2 transceiver details     
 Ethernet2/2                                       
      transceiver is present                        
      type is QSFP-40G-SR4                         
      name is CISCO                                 
      part number is AFBR-79EIPZ-CS1                
      revision is 02                                
      serial number is AVP1606S381                  
      nominal bitrate is 10300 MBit/sec per channel     
      Link length supported for 50/125um OM2 fiber is 30 m     
      Link length supported for 50/125um OM3 fiber is 100 m     
      cisco id is 13                                            
      cisco extended id number is 16

CLI Output
Lane Number:1 Network Lane SFP Detail Diagnostics Information (internal calibration) ---------------------------------------------------------------------------- Current Alarms Warnings Measurement High Low High Low ---------------------------------------------------------------------------- Temperature 24.65 C 75.00 C -5.00 C 70.00 C 0.00 C Voltage 3.40 V 3.63 V 2.97 V 3.46 V 3.09 V Current N/A N/A N/A N/A N/A Tx Power N/A N/A N/A N/A N/A Rx Power N/A N/A N/A N/A N/A Transmit Fault Count = 0 ---------------------------------------------------------------------------- Note: ++ high-alarm; + high-warning; -- low-alarm; - low-warning ...

CLI Output

 Lane Number:1 Network Lane    
        SFP Detail Diagnostics Information (internal calibration)   
   ----------------------------------------------------------------------------    
                Current                Alarms                   Warnings          
                Measurement    High        Low        High         Low   
  ----------------------------------------------------------------------------     
  Temperature   24.65 C       75.00 C     -5.00 C     70.00 C      0.00 C   
  Voltage        3.40 V        3.63 V      2.97 V      3.46 V      3.09 V  
  Current           N/A           N/A       N/A       N/A            N/A   
  Tx Power          N/A           N/A       N/A       N/A            N/A    
  Rx Power          N/A           N/A       N/A       N/A            N/A   
  Transmit Fault Count = 0    
  ----------------------------------------------------------------------------    
  Note: ++  high-alarm; +  high-warning; --  low-alarm; -  low-warning    
 ...

Note: The property information for this example was added in Release 9.3(3).

MO	DN
eqptFcotSensor	sys/intf/phys-{[id]}/phys/fcot/lane-{laneId}-sensor-{sensorId}

eqptFcotSensor Properties

The following table contains information about the eqptFcotSensor properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
description	string:Basic	The transceiver sensor description	A sequence of characters
dn	reference:BinRef	A tag or metadata is a non-hierarchical keyword or term assigned to the fabric module.
highAlarm	scalar:Float	The transceiver sensor high alarm threshold	A floating number per IEEE-754 standard
highWarning	scalar:Float	The transceiver sensor high warning threshold	A floating number per IEEE-754 standard
laneId	scalar:Uint16	The transceiver LANE identifier	RANGE: [0, 65535]
laneType	eqpt:fcotDomLane (scalar:Enum8)	The transceiver LANE type	SELECTION: 0 - basic 1 - extGlobal 2 - extOptical
lowAlarm	scalar:Float	The transceiver sensor low alarm threshold	A floating number per IEEE-754 standard
lowWarning	scalar:Float	The transceiver sensor low warning threshold	A floating number per IEEE-754 standard
sensorId	scalar:Uint16	The transceiver sensor identifier	RANGE: [0, 65535]
unit	string:Basic	The transceiver sensor unit	A sequence of characters
value	scalar:Float	The transceiver sensor current value	A floating number per IEEE-754 standard

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Querying the Temperature Details for the Sensor

Provides transceiver sensor information.

CLI Commands

The DME payload provides the lane number and voltage (description), current measurement (value), alarms (highAlarm and lowAlarm), warnings (highWarning and lowWarning), and the sensor unit (unit) given in the show interface ethernet slot/port transceiver output. Compare the payload with the CLI Output.

CLI Output
switch# show interface e2/2 transceiver details Ethernet2/2 transceiver is present type is QSFP-40G-SR4 name is CISCO part number is AFBR-79EIPZ-CS1 revision is 02 serial number is AVP1606S381 nominal bitrate is 10300 MBit/sec per channel Link length supported for 50/125um OM2 fiber is 30 m Link length supported for 50/125um OM3 fiber is 100 m cisco id is 13 cisco extended id number is 16 Lane Number:1 Network Lane SFP Detail Diagnostics Information (internal calibration) ---------------------------------------------------------------------------- Current Alarms Warnings Measurement High Low High Low ---------------------------------------------------------------------------- Temperature 24.65 C 75.00 C -5.00 C 70.00 C 0.00 C Voltage 3.40 V 3.63 V 2.97 V 3.46 V 3.09 V Current N/A N/A N/A N/A N/A Tx Power N/A N/A N/A N/A N/A Rx Power N/A N/A N/A N/A N/A Transmit Fault Count = 0 ---------------------------------------------------------------------------- Note: ++ high-alarm; + high-warning; -- low-alarm; - low-warning ...

CLI Output

  switch# show interface e2/2 transceiver details   
 Ethernet2/2                                       
      transceiver is present                        
      type is QSFP-40G-SR4                          
      name is CISCO                                 
      part number is AFBR-79EIPZ-CS1               
      revision is 02                                
      serial number is AVP1606S381                  
      nominal bitrate is 10300 MBit/sec per channel     
      Link length supported for 50/125um OM2 fiber is 30 m     
      Link length supported for 50/125um OM3 fiber is 100 m     
      cisco id is 13                                            
      cisco extended id number is 16                           
 Lane Number:1 Network Lane    
        SFP Detail Diagnostics Information (internal calibration)   
   ----------------------------------------------------------------------------      
                Current                Alarms                   Warnings            
                Measurement    High        Low        High         Low      
  ----------------------------------------------------------------------------      
  Temperature   24.65 C       75.00 C   -5.00 C      70.00 C         0.00 C    
  Voltage        3.40 V        3.63 V    2.97 V       3.46 V         3.09 V    
  Current           N/A           N/A       N/A          N/A            N/A    
  Tx Power          N/A           N/A       N/A          N/A            N/A      
  Rx Power          N/A           N/A       N/A          N/A            N/A    
  Transmit Fault Count = 0     
  ----------------------------------------------------------------------------     
  Note: ++  high-alarm; +  high-warning; --  low-alarm; -  low-warning     
 ...

Note: The property information for this example was added in Release 9.3(3).

MO	DN
eqptFcotSensor	sys/intf/phys-{[id]}/phys/fcot/lane-{laneId}-sensor-{sensorId}

eqptFcotSensor Properties

Property Name	Data Type	Description	Values
description	string:Basic	The transceiver sensor description	A sequence of characters
dn	reference:BinRef	A tag or metadata is a non-hierarchical keyword or term assigned to the fabric module.
highAlarm	scalar:Float	The transceiver sensor high alarm threshold	A floating number per IEEE-754 standard
highWarning	scalar:Float	The transceiver sensor high warning threshold	A floating number per IEEE-754 standard
laneId	scalar:Uint16	The transceiver LANE identifier	RANGE: [0, 65535]
laneType	eqpt:fcotDomLane (scalar:Enum8)	The transceiver LANE type	SELECTION: 0 - basic 1 - extGlobal 2 - extOptical
lowAlarm	scalar:Float	The transceiver sensor low alarm threshold	A floating number per IEEE-754 standard
lowWarning	scalar:Float	The transceiver sensor low warning threshold	A floating number per IEEE-754 standard
sensorId	scalar:Uint16	The transceiver sensor identifier	RANGE: [0, 65535]
unit	string:Basic	The transceiver sensor unit	A sequence of characters
value	scalar:Float	The transceiver sensor current value	A floating number per IEEE-754 standard

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html