Cisco Nexus 3000 and 9000 Series NX-API REST SDK User Guide and API Reference, Release 10.5(x)

Cisco Nexus 3000 and 9000 Series NX-API REST Documentation

Configuring Override of Some PTP Profile Parameters on an Interface

DME

YANG

Copy
POST http://<mgmt0_IP>/api/mo/sys.json
{
  "topSystem": {
    "children": [
      {
        "ptpPtpEntity": {
          "children": [
            {
              "ptpPtpIf": {
                "attributes": {
                  "id": "eth1/3",
                  "profileOverride": "yes"
                }
              }
            }
          ]
        }
      },
      {
        "interfaceEntity": {
          "children": [
            {
              "l1PhysIf": {
                "attributes": {
                  "id": "eth1/3"
                }
              }
            }
          ]
        }
      }
    ]
  }
}
Response
{
    imdata:[]
}

Copy
<System>
  <ptp-items>
    <if-items>
      <PtpIf-list>
        <id>eth1/3</id>
        <profileOverride>true</profileOverride>
      </PtpIf-list>
    </if-items>
  </ptp-items>
  <intf-items>
    <phys-items>
      <PhysIf-list>
        <id>eth1/3</id>
      </PhysIf-list>
    </phys-items>
  </intf-items>
</System>

Configuring an Interface

Configuring Override of Some PTP Profile Parameters on an Interface

Note: This example was added in Release 9.3(5).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

interface ethernet 1/3
ptp profile-override

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

MO	DN
topSystem	sys
ptpPtpEntity	sys/ptp
ptpPtpIf	sys/ptp/if-[eth1/3]
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/3]

ptpPtpIf Properties

The following table contains information about the ptpPtpIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	Interface id of port with PTP configuration	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
profileOverride	scalar:Bool	Allow override of configuration limits imposed by global PTP profile	SELECTION: true or false DEFAULT: false

l1PhysIf Properties

The following table contains information about the l1PhysIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Override of Some PTP Profile Parameters on an Interface

Note: This example was added in Release 9.3(5).

CLI Commands

interface ethernet 1/3
no ptp profile-override

Verifying a DME Configuration

MO	DN
topSystem	sys
ptpPtpEntity	sys/ptp
ptpPtpIf	sys/ptp/if-[eth1/3]
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/3]

ptpPtpIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	Interface id of port with PTP configuration	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
profileOverride	scalar:Bool	Allow override of configuration limits imposed by global PTP profile	SELECTION: true or false DEFAULT: false

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Packet Acceptance and Response Based on Config (Non-Forwardable)

This example is only supported on the N9K-C93180YC-FX3S platform and will take effect when the ethernet transport is configured on an interface.

Note: This example was added in Release 9.3(5).

CLI Commands

interface ethernet 1/3
ptp destination-mac non-forwardable rx-no-match accept

Verifying a DME Configuration

MO	DN
topSystem	sys
ptpPtpEntity	sys/ptp
ptpPtpIf	sys/ptp/if-[eth1/3]
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/3]

ptpPtpIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	Interface id of port with PTP configuration	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
ptpDestinationMac	ptp:PtpDestinationMac (scalar:Enum8)	PTP destination mac forwardable or non-forwardable	SELECTION: 0 - non-forwardable 1 - forwardable DEFAULT: non-forwardable
ptpRxNoMatch	ptp:PtpRxNoMatch (scalar:Enum8)	PTP packets destination MAC with RX packet not matching	SELECTION: 0 - accept 1 - drop 2 - follow-rx DEFAULT: accept

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Packet Acceptance and Response Based on Config (Non-Forwardable)

Note: This example was added in Release 9.3(5).

CLI Commands

interface ethernet 1/3
no ptp destination-mac non-forwardable rx-no-match accept

Verifying a DME Configuration

MO	DN
topSystem	sys
ptpPtpEntity	sys/ptp
ptpPtpIf	sys/ptp/if-[eth1/3]
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/3]

ptpPtpIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	Interface id of port with PTP configuration	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
ptpDestinationMac	ptp:PtpDestinationMac (scalar:Enum8)	PTP destination mac forwardable or non-forwardable	SELECTION: 0 - non-forwardable 1 - forwardable DEFAULT: non-forwardable
ptpRxNoMatch	ptp:PtpRxNoMatch (scalar:Enum8)	PTP packets destination MAC with RX packet not matching	SELECTION: 0 - accept 1 - drop 2 - follow-rx DEFAULT: accept

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Drop Packet and No Response (Non-Forwardable)

This example is only supported on the N9K-C93180YC-FX3S platform and will take effect when the ethernet transport is configured on an interface.

Note: This example was added in Release 9.3(5).

CLI Commands

interface ethernet 1/3
ptp destination-mac non-forwardable rx-no-match drop

Verifying a DME Configuration

MO	DN
topSystem	sys
ptpPtpEntity	sys/ptp
ptpPtpIf	sys/ptp/if-[eth1/3]
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/3]

ptpPtpIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	Interface id of port with PTP configuration	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
ptpDestinationMac	ptp:PtpDestinationMac (scalar:Enum8)	PTP destination mac forwardable or non-forwardable	SELECTION: 0 - non-forwardable 1 - forwardable DEFAULT: non-forwardable
ptpRxNoMatch	ptp:PtpRxNoMatch (scalar:Enum8)	PTP packets destination MAC with RX packet not matching	SELECTION: 0 - accept 1 - drop 2 - follow-rx DEFAULT: accept

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Drop Packet and No Response (Non-Forwardable)

Note: This example was added in Release 9.3(5).

CLI Commands

interface ethernet 1/3
no ptp destination-mac non-forwardable rx-no-match drop

Verifying a DME Configuration

MO	DN
topSystem	sys
ptpPtpEntity	sys/ptp
ptpPtpIf	sys/ptp/if-[eth1/3]
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/3]

ptpPtpIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	Interface id of port with PTP configuration	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
ptpDestinationMac	ptp:PtpDestinationMac (scalar:Enum8)	PTP destination mac forwardable or non-forwardable	SELECTION: 0 - non-forwardable 1 - forwardable DEFAULT: non-forwardable
ptpRxNoMatch	ptp:PtpRxNoMatch (scalar:Enum8)	PTP packets destination MAC with RX packet not matching	SELECTION: 0 - accept 1 - drop 2 - follow-rx DEFAULT: accept

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Packet Acceptance and Response Based on Received Packet (Non-Forwardable)

This example is only supported on the N9K-C93180YC-FX3S platform and will take effect when the ethernet transport is configured on an interface.

Note: This example was added in Release 9.3(5).

CLI Commands

interface ethernet 1/3
ptp destination-mac non-forwardable rx-no-match follow-rx

Verifying a DME Configuration

MO	DN
topSystem	sys
ptpPtpEntity	sys/ptp
ptpPtpIf	sys/ptp/if-[eth1/3]
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/3]

ptpPtpIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	Interface id of port with PTP configuration	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
ptpDestinationMac	ptp:PtpDestinationMac (scalar:Enum8)	PTP destination mac forwardable or non-forwardable	SELECTION: 0 - non-forwardable 1 - forwardable DEFAULT: non-forwardable
ptpRxNoMatch	ptp:PtpRxNoMatch (scalar:Enum8)	PTP packets destination MAC with RX packet not matching	SELECTION: 0 - accept 1 - drop 2 - follow-rx DEFAULT: accept

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Packet Acceptance and Response Based on Received Packet (Non-Forwardable)

Note: This example was added in Release 9.3(5).

CLI Commands

interface ethernet 1/3
no ptp destination-mac non-forwardable rx-no-match follow-rx

Verifying a DME Configuration

MO	DN
topSystem	sys
ptpPtpEntity	sys/ptp
ptpPtpIf	sys/ptp/if-[eth1/3]
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/3]

ptpPtpIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	Interface id of port with PTP configuration	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
ptpDestinationMac	ptp:PtpDestinationMac (scalar:Enum8)	PTP destination mac forwardable or non-forwardable	SELECTION: 0 - non-forwardable 1 - forwardable DEFAULT: non-forwardable
ptpRxNoMatch	ptp:PtpRxNoMatch (scalar:Enum8)	PTP packets destination MAC with RX packet not matching	SELECTION: 0 - accept 1 - drop 2 - follow-rx DEFAULT: accept

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Packet Acceptance and Response Based on Config (Forwardable)

This example is only supported on the N9K-C93180YC-FX3S platform and will take effect when the ethernet transport is configured on an interface.

Note: This example was added in Release 9.3(5).

CLI Commands

interface ethernet 1/3
ptp destination-mac forwardable rx-no-match accept

Verifying a DME Configuration

MO	DN
topSystem	sys
ptpPtpEntity	sys/ptp
ptpPtpIf	sys/ptp/if-[eth1/3]
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/3]

ptpPtpIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	Interface id of port with PTP configuration	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
ptpDestinationMac	ptp:PtpDestinationMac (scalar:Enum8)	PTP destination mac forwardable or non-forwardable	SELECTION: 0 - non-forwardable 1 - forwardable DEFAULT: non-forwardable
ptpRxNoMatch	ptp:PtpRxNoMatch (scalar:Enum8)	PTP packets destination MAC with RX packet not matching	SELECTION: 0 - accept 1 - drop 2 - follow-rx DEFAULT: accept

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Packet Acceptance and Response Based on Config (Forwardable)

Note: This example was added in Release 9.3(5).

CLI Commands

interface ethernet 1/3
no ptp destination-mac forwardable rx-no-match accept

Verifying a DME Configuration

MO	DN
topSystem	sys
ptpPtpEntity	sys/ptp
ptpPtpIf	sys/ptp/if-[eth1/3]
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/3]

ptpPtpIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	Interface id of port with PTP configuration	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
ptpDestinationMac	ptp:PtpDestinationMac (scalar:Enum8)	PTP destination mac forwardable or non-forwardable	SELECTION: 0 - non-forwardable 1 - forwardable DEFAULT: non-forwardable
ptpRxNoMatch	ptp:PtpRxNoMatch (scalar:Enum8)	PTP packets destination MAC with RX packet not matching	SELECTION: 0 - accept 1 - drop 2 - follow-rx DEFAULT: accept

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Drop Packet and No Response (Forwardable)

This example is only supported on the N9K-C93180YC-FX3S platform and will take effect when the ethernet transport is configured on an interface.

Note: This example was added in Release 9.3(5).

CLI Commands

interface ethernet 1/3
ptp destination-mac forwardable rx-no-match drop

Verifying a DME Configuration

MO	DN
topSystem	sys
ptpPtpEntity	sys/ptp
ptpPtpIf	sys/ptp/if-[eth1/3]
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/3]

ptpPtpIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	Interface id of port with PTP configuration	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
ptpDestinationMac	ptp:PtpDestinationMac (scalar:Enum8)	PTP destination mac forwardable or non-forwardable	SELECTION: 0 - non-forwardable 1 - forwardable DEFAULT: non-forwardable
ptpRxNoMatch	ptp:PtpRxNoMatch (scalar:Enum8)	PTP packets destination MAC with RX packet not matching	SELECTION: 0 - accept 1 - drop 2 - follow-rx DEFAULT: accept

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Drop Packet and No Response (Forwardable)

Note: This example was added in Release 9.3(5).

CLI Commands

interface ethernet 1/3
no ptp destination-mac forwardable rx-no-match drop

Verifying a DME Configuration

MO	DN
topSystem	sys
ptpPtpEntity	sys/ptp
ptpPtpIf	sys/ptp/if-[eth1/3]
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/3]

ptpPtpIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	Interface id of port with PTP configuration	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
ptpDestinationMac	ptp:PtpDestinationMac (scalar:Enum8)	PTP destination mac forwardable or non-forwardable	SELECTION: 0 - non-forwardable 1 - forwardable DEFAULT: non-forwardable
ptpRxNoMatch	ptp:PtpRxNoMatch (scalar:Enum8)	PTP packets destination MAC with RX packet not matching	SELECTION: 0 - accept 1 - drop 2 - follow-rx DEFAULT: accept

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Packet Acceptance and Response Based on Received Packet (Forwardable)

This example is only supported on the N9K-C93180YC-FX3S platform and will take effect when the ethernet transport is configured on an interface.

Note: This example was added in Release 9.3(5).

CLI Commands

interface ethernet 1/3
ptp destination-mac forwardable rx-no-match follow-rx

Verifying a DME Configuration

MO	DN
topSystem	sys
ptpPtpEntity	sys/ptp
ptpPtpIf	sys/ptp/if-[eth1/3]
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/3]

ptpPtpIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	Interface id of port with PTP configuration	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
ptpDestinationMac	ptp:PtpDestinationMac (scalar:Enum8)	PTP destination mac forwardable or non-forwardable	SELECTION: 0 - non-forwardable 1 - forwardable DEFAULT: non-forwardable
ptpRxNoMatch	ptp:PtpRxNoMatch (scalar:Enum8)	PTP packets destination MAC with RX packet not matching	SELECTION: 0 - accept 1 - drop 2 - follow-rx DEFAULT: accept

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Packet Acceptance and Response Based on Received Packet (Forwardable)

Note: This example was added in Release 9.3(5).

CLI Commands

interface ethernet 1/3
no ptp destination-mac forwardable rx-no-match follow-rx

Verifying a DME Configuration

MO	DN
topSystem	sys
ptpPtpEntity	sys/ptp
ptpPtpIf	sys/ptp/if-[eth1/3]
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/3]

ptpPtpIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	Interface id of port with PTP configuration	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
ptpDestinationMac	ptp:PtpDestinationMac (scalar:Enum8)	PTP destination mac forwardable or non-forwardable	SELECTION: 0 - non-forwardable 1 - forwardable DEFAULT: non-forwardable
ptpRxNoMatch	ptp:PtpRxNoMatch (scalar:Enum8)	PTP packets destination MAC with RX packet not matching	SELECTION: 0 - accept 1 - drop 2 - follow-rx DEFAULT: accept

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring PTP Ethernet Transport

Note: This example was added in Release 9.3(5).

CLI Commands

interface ethernet 1/3
ptp transport ethernet

Verifying a DME Configuration

MO	DN
topSystem	sys
ptpPtpEntity	sys/ptp
ptpPtpIf	sys/ptp/if-[eth1/3]
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/3]

ptpPtpIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	Interface id of port with PTP configuration	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
transport	ptp:TransportType (scalar:Enum8)	Transport type for PTP interface with default IPv4	SELECTION: 1 - ipv4 2 - eth DEFAULT: ipv4

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting PTP Ethernet Transport

Note: This example was added in Release 9.3(5).

CLI Commands

interface ethernet 1/3
no ptp transport ethernet

Verifying a DME Configuration

MO	DN
topSystem	sys
ptpPtpEntity	sys/ptp
ptpPtpIf	sys/ptp/if-[eth1/3]
interfaceEntity	sys/intf
l1PhysIf	sys/intf/phys-[eth1/3]

ptpPtpIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	Interface id of port with PTP configuration	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100
transport	ptp:TransportType (scalar:Enum8)	Transport type for PTP interface with default IPv4	SELECTION: 1 - ipv4 2 - eth DEFAULT: ipv4

l1PhysIf Properties

Property Name	Data Type	Description	Values
id	nw:IfId (base:IfIndex)	An identifier .	Must match first field in the output of `show intf brief`. Example: Eth1/1 or Vlan100

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Cost Associated With the Interface

Note: The default value is 128 when an 8275-1 profile is configured.

For an example payload, see [Configuring the Cost Associated With the Interface](Configuring the Cost Associated With the Interface).

Configuring a PTP Role

Note: You cannot change the default value of dynamic when an 8275-1 profile is configured.

For an example payload, see [Configuring a Dynamic PTP Role](Configuring a Dynamic PTP Role).

Configuring PTP Transmission

Note: You cannot change the default value of multicast when an 8275-1 profile is configured.

For an example payload, see [Configuring PTP Multicast Transmission](Configuring PTP Multicast Transmission).

Configuring PTP Transport

Note: The default value is ethernet when an 8275-1 profile is configured and can be modified only when a profile-override is applied to interface. The ethernet option is only available on N9K-C93180YC-FX3S platform.

For an example payload, see [Configuring PTP Multicast Transmission](Configuring PTP Multicast Transmission).

Configuring PTP Announce Interval

Note: The default value is -3 when an 8275-1 profile is configured and can be modified only when a profile-override is applied to the interface.

For an example payload, see [Configuring PTP Announce Interval](Configuring PTP Announce Interval).

Configuring the PTP Delay Request Minimum Interval

Note: The default value is -4 when an 8275-1 profile is configured and can be modified only when a profile-override is applied to the interface.

For an example payload, see [Configuring the PTP Delay Request Minimum Interval](Configuring the PTP Delay Request Minimum Interval).

Configuring the PTP Sync Interval

Note: The default value is -4 when an 8275-1 profile is configured and can be modified only when a profile-override is applied to the interface.

For an example payload, see [Configuring the PTP Sync Interval](Configuring the PTP Sync Interval).