Configuring an IPv6 Labeled-Unicast Address Family

This section uses examples to demonstrate BGP configuration options and to show how the REST APIs correspond to the CLI commands.

Configuring a Route Map to Selectively Unsuppress Suppressed Routes

Configuring a Route Map to Selectively Unsuppress Suppressed Routes

POST http://<mgmt0_IP>/api/mo/sys/bgp/inst.json

{
  "bgpInst": {
    "attributes": {
      "asn": "100"
    },
    "children": [
      {
        "bgpDom": {
          "attributes": {
            "name": "default"
          },
          "children": [
            {
              "bgpPeer": {
                "attributes": {
                  "addr": "1.2.3.4",
                  "inheritContPeerCtrl": ""
                },
                "children": [
                  {
                    "bgpPeerAf": {
                      "attributes": {
                        "inheritContPeerPolicyCtrl": "",
                        "type": "ipv6-lucast",
                        "unSupprMap": "map1"

}}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <unSupprMap>map1</unSupprMap>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
   unsuppress-map map1

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting a Route Map to Selectively Unsuppress Suppressed Routes for a Peer (Values inherited from a Peer Template)

Deleting a Route Map to Selectively Unsuppress Suppressed Routes for a Peer (Values inherited from a Peer Template)

POST http://<mgmt0_IP>/api/mo/sys/bgp/inst.json

{
  "bgpInst": {
    "attributes": {
      "asn": "100"
    },
    "children": [
      {
        "bgpDom": {
          "attributes": {
            "name": "default"
          },
          "children": [
            {
              "bgpPeer": {
                "attributes": {
                  "addr": "1.2.3.4",
                  "inheritContPeerCtrl": ""
                },
                "children": [
                  {
                    "bgpPeerAf": {
                      "attributes": {
                        "inheritContPeerPolicyCtrl": "unsuppr-map",
                        "type": "ipv6-lucast",
                        "unSupprMap": "map1"
                      },
                      "children": [
                        {
                          "bgpPolicyInheritRule": {
                            "attributes": {
                              "name": "pol",
                              "seq": "1"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <inheritContPeerPolicyCtrl>unsuppr-map</inheritContPeerPolicyCtrl>
                  <unSupprMap>map1</unSupprMap>
                  <pol-items>
                    <PolicyInheritRule-list>
                      <name>pol</name>
                      <seq>1</seq>
                    </PolicyInheritRule-list>
                  </pol-items>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
   inherit peer-policy pol 1
   no unsuppress-map map1

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPolicyInheritRule Properties

The following table contains information about the bgpPolicyInheritRule properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Applying an AS-PATH Filter List to Incoming Routes

Applying an AS-PATH Filter List to Incoming Routes 

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

 {
  "topSystem": {
    "children": [
      {
        "rpmEntity": {
          "children": [
            {
              "rtlistRule": {
                "attributes": {
                  "name": "List_A"
                },
                "children": [
                  {
                    "rtlistEntry": {
                      "attributes": {
                        "action": "permit",
                        "order": "10",
                        "regex": "1"
}}}]}}]}},{
        "bgpEntity": {
          "children": [
            {
              "bgpInst": {
                "attributes": {
                  "asn": "123"
                },
                "children": [
                  {
                    "bgpDom": {
                      "attributes": {
                        "name": "default"
                      },
                      "children": [
                        {
                          "bgpPeer": {
                            "attributes": {
                              "addr": "1.2.3.4",
                              "inheritContPeerCtrl": ""
                            },
                            "children": [
                              {
                                "bgpPeerAf": {
                                  "attributes": {
                                    "inheritContPeerPolicyCtrl": "",
                                    "type": "ipv6-lucast"
                                  },
                                  "children": [
                                    {
                                      "bgpFltrCtrlP": {
                                        "attributes": {
                                          "direction": "in",
                                          "list": "List_A"
}}}]}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <rpm-items>
    <accesslist-items>
      <Rule-list>
        <name>List_A</name>
        <ent-items>
          <Entry-list>
            <order>10</order>
            <action>permit</action>
            <regex>1</regex>
          </Entry-list>
        </ent-items>
      </Rule-list>
    </accesslist-items>
  </rpm-items>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <fltrctrl-items>
                    <FltrCtrlP-list>
                      <direction>in</direction>
                      <list>List_A</list>
                    </FltrCtrlP-list>
                  </fltrctrl-items>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

ip as-path access-list List_A seq 10 permit 1
router bgp 123
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
   filter-list List_A in

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference: http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload: https://developer.cisco.com/media/dme/index.html

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Applying an AS-PATH Filter List to Outgoing Routes

Applying an AS-PATH Filter List to Outgoing Routes 

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "rpmEntity": {
          "children": [
            {
              "rtlistRule": {
                "attributes": {
                  "name": "List_A"
                },
                "children": [
                  {
                    "rtlistEntry": {
                      "attributes": {
                        "action": "permit",
                        "order": "10",
                        "regex": "1"
}}}]}}]}},{
        "bgpEntity": {
          "children": [
            {
              "bgpInst": {
                "attributes": {
                  "asn": "123"
                },
                "children": [
                  {
                    "bgpDom": {
                      "attributes": {
                        "name": "default"
                      },
                      "children": [
                        {
                          "bgpPeer": {
                            "attributes": {
                              "addr": "1.2.3.4",
                              "inheritContPeerCtrl": ""
                            },
                            "children": [
                              {
                                "bgpPeerAf": {
                                  "attributes": {
                                    "inheritContPeerPolicyCtrl": "",
                                    "type": "ipv6-lucast"
                                  },
                                  "children": [
                                    {
                                      "bgpFltrCtrlP": {
                                        "attributes": {
                                          "direction": "out",
                                          "list": "List_A"
}}}]}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <rpm-items>
    <accesslist-items>
      <Rule-list>
        <name>List_A</name>
        <ent-items>
          <Entry-list>
            <order>10</order>
            <action>permit</action>
            <regex>1</regex>
          </Entry-list>
        </ent-items>
      </Rule-list>
    </accesslist-items>
  </rpm-items>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <fltrctrl-items>
                    <FltrCtrlP-list>
                      <direction>out</direction>
                      <list>List_A</list>
                    </FltrCtrlP-list>
                  </fltrctrl-items>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

ip as-path access-list List_A seq 10 permit 1
router bgp 123
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
   filter-list List_A out

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

rtlistRule Properties

The following table contains information about the rtlistRule properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

rtlistEntry Properties

The following table contains information about the rtlistEntry properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpFltrCtrlP Properties

The following table contains information about the bgpFltrCtrlP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Applying a Prefix List to Incoming Routes

Applying a Prefix List to Incoming Routes 

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "rpmEntity": {
          "children": [
            {
              "rtpfxRuleV4": {
                "attributes": {
                  "name": "List_1"
                },
                "children": [
                  {
                    "rtpfxEntry": {
                      "attributes": {
                        "action": "permit",
                        "criteria": "exact",
                        "fromPfxLen": "0",
                        "order": "10",
                        "pfx": "4.3.2.1/3",
                        "toPfxLen": "0"
}}}]}}]}},{
        "bgpEntity": {
          "children": [
            {
              "bgpInst": {
                "attributes": {
                  "asn": "123"
                },
                "children": [
                  {
                    "bgpDom": {
                      "attributes": {
                        "name": "default"
                      },
                      "children": [
                        {
                          "bgpPeer": {
                            "attributes": {
                              "addr": "1.2.3.4",
                              "inheritContPeerCtrl": ""
                            },
                            "children": [
                              {
                                "bgpPeerAf": {
                                  "attributes": {
                                    "inheritContPeerPolicyCtrl": "",
                                    "type": "ipv6-lucast"
                                  },
                                  "children": [
                                    {
                                      "bgpPfxCtrlP": {
                                        "attributes": {
                                          "direction": "in",
                                          "list": "List_1"
}}}]}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <rpm-items>
    <pfxlistv4-items>
      <RuleV4-list>
        <name>List_1</name>
        <ent-items>
          <Entry-list>
            <order>10</order>
            <action>permit</action>
            <criteria>exact</criteria>
            <fromPfxLen>0</fromPfxLen>
            <pfx>4.3.2.1/3</pfx>
            <toPfxLen>0</toPfxLen>
          </Entry-list>
        </ent-items>
      </RuleV4-list>
    </pfxlistv4-items>
  </rpm-items>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <pfxctrl-items>
                    <PfxCtrlP-list>
                      <direction>in</direction>
                      <list>List_1</list>
                    </PfxCtrlP-list>
                  </pfxctrl-items>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

ip prefix-list List_1 seq 10 permit 4.3.2.1/3
router bgp 123
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
   prefix-list List_1 in

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

rtpfxRuleV4 Properties

The following table contains information about the rtpfxRuleV4 properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

rtpfxEntry Properties

The following table contains information about the rtpfxEntry properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPfxCtrlP Properties

The following table contains information about the bgpPfxCtrlP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Applying a Prefix List to Outgoing Routes

Applying a Prefix List to Outgoing Routes 

POST http://<mgmt0_IP>/api/mo/sys.json

{
  "topSystem": {
    "children": [
      {
        "rpmEntity": {
          "children": [
            {
              "rtpfxRuleV4": {
                "attributes": {
                  "name": "List_1"
                },
                "children": [
                  {
                    "rtpfxEntry": {
                      "attributes": {
                        "action": "permit",
                        "criteria": "exact",
                        "fromPfxLen": "0",
                        "order": "10",
                        "pfx": "4.3.2.1/3",
                        "toPfxLen": "0"
}}}]}}]}},{
        "bgpEntity": {
          "children": [
            {
              "bgpInst": {
                "attributes": {
                  "asn": "123"
                },
                "children": [
                  {
                    "bgpDom": {
                      "attributes": {
                        "name": "default"
                      },
                      "children": [
                        {
                          "bgpPeer": {
                            "attributes": {
                              "addr": "1.2.3.4",
                              "inheritContPeerCtrl": ""
                            },
                            "children": [
                              {
                                "bgpPeerAf": {
                                  "attributes": {
                                    "inheritContPeerPolicyCtrl": "",
                                    "type": "ipv6-lucast"
                                  },
                                  "children": [
                                    {
                                      "bgpPfxCtrlP": {
                                        "attributes": {
                                          "direction": "out",
                                          "list": "List_1"
}}}]}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <rpm-items>
    <pfxlistv4-items>
      <RuleV4-list>
        <name>List_1</name>
        <ent-items>
          <Entry-list>
            <order>10</order>
            <action>permit</action>
            <criteria>exact</criteria>
            <fromPfxLen>0</fromPfxLen>
            <pfx>4.3.2.1/3</pfx>
            <toPfxLen>0</toPfxLen>
          </Entry-list>
        </ent-items>
      </RuleV4-list>
    </pfxlistv4-items>
  </rpm-items>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <pfxctrl-items>
                    <PfxCtrlP-list>
                      <direction>out</direction>
                      <list>List_1</list>
                    </PfxCtrlP-list>
                  </pfxctrl-items>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

ip prefix-list List_1 seq 10 permit 4.3.2.1/3
router bgp 123
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
   prefix-list List_1 out

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

rtpfxRuleV4 Properties

The following table contains information about the rtpfxRuleV4 properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

rtpfxEntry Properties

The following table contains information about the rtpfxEntry properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPfxCtrlP Properties

The following table contains information about the bgpPfxCtrlP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring to Advertise Only Active Routes to the Peer

Configuring to Advertise Only Active Routes to the Peer

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "123"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeer": {
                      "attributes": {
                        "addr": "1.2.3.4",
                        "inheritContPeerCtrl": ""
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "ctrl": "suppress-inactive",
                              "inheritContPeerPolicyCtrl": "",
                              "type": "ipv6-lucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <ctrl>suppress-inactive</ctrl>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
  suppress-inactive

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting the Configuration for Advertising Only Active Routes to the Peer

Deleting the Configuration for Advertising Only Active Routes to the Peer

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "123"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeer": {
                      "attributes": {
                        "addr": "1.2.3.4",
                        "inheritContPeerCtrl": ""
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "ctrl": "",
                              "inheritContPeerPolicyCtrl": "",
                              "type": "ipv6-lucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <ctrl></ctrl>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
  no suppress-inactive

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Advertise Only Active Routes to the Peer (Values inherited from a Peer Template)

Advertise Only Active Routes to the Peer (Values inherited from a Peer Template)

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

 {
  "topSystem": {
    "children": [
      {
        "bgpEntity": {
          "children": [
            {
              "bgpInst": {
                "attributes": {
                  "asn": "123"
                },
                "children": [
                  {
                    "bgpDom": {
                      "attributes": {
                        "name": "default"
                      },
                      "children": [
                        {
                          "bgpPeer": {
                            "attributes": {
                              "addr": "1.2.3.4",
                              "inheritContPeerCtrl": ""
                            },
                            "children": [
                              {
                                "bgpPeerAf": {
                                  "attributes": {
                                    "ctrl": "",
                                    "inheritContPeerPolicyCtrl": "",
                                    "type": "ipv6-lucast"
                                  },
                                  "children": [
                                    {
                                      "bgpPolicyInheritRule": {
                                        "attributes": {
                                          "name": "Pol1",
                                          "seq": "123"
                                        }
                                      }
                                    }
                                  ]
                                }
                              }
                            ]
                          }
                        },
                        {
                          "bgpPolicyCont": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "name": "Pol1"
                            }
                          }
                        }
                      ]
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <ctrl></ctrl>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <pol-items>
                    <PolicyInheritRule-list>
                      <name>Pol1</name>
                      <seq>123</seq>
                    </PolicyInheritRule-list>
                  </pol-items>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
          <policycont-items>
            <PolicyCont-list>
              <name>Pol1</name>
              <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
            </PolicyCont-list>
          </policycont-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 template peer-policy Pol1
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
   inherit peer-policy Pol1 123
    default suppress-inactive

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference: http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload: https://developer.cisco.com/media/dme/index.html

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Receive Capability for Additional Paths

Configuring Receive Capability for Additional Paths

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "123"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeer": {
                      "attributes": {
                        "addr": "1.2.3.4",
                        "inheritContPeerCtrl": ""
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "capAddlPaths": "recv",
                              "inheritContPeerPolicyCtrl": "",
                              "type": "ipv6-lucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <capAddlPaths>recv</capAddlPaths>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
  capability additional-paths receive

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Disabling Receive Capability for Additional Paths

Disabling Receive Capability for Additional Paths

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "123"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeer": {
                      "attributes": {
                        "addr": "1.2.3.4",
                        "inheritContPeerCtrl": ""
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "capAddlPaths": "recv-disable",
                              "inheritContPeerPolicyCtrl": "",
                              "type": "ipv6-lucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <capAddlPaths>recv-disable</capAddlPaths>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
  capability additional-paths receive disable

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Receive Capability for Additional Paths

Deleting Receive Capability for Additional Paths

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "123"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeer": {
                      "attributes": {
                        "addr": "1.2.3.4",
                        "inheritContPeerCtrl": ""
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "capAddlPaths": "",
                              "inheritContPeerPolicyCtrl": "",
                              "type": "ipv6-lucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <capAddlPaths></capAddlPaths>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
  no capability additional-paths receive

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Receive Capability for Additional Paths (Values inherited from a Peer Template)

Configuring Receive Capability for Additional Paths (Values inherited from a Peer Template)

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "topSystem": {
    "children": [
      {
        "bgpEntity": {
          "children": [
            {
              "bgpInst": {
                "attributes": {
                  "asn": "123"
                },
                "children": [
                  {
                    "bgpDom": {
                      "attributes": {
                        "name": "default"
                      },
                      "children": [
                        {
                          "bgpPeer": {
                            "attributes": {
                              "addr": "1.2.3.4",
                              "inheritContPeerCtrl": ""
                            },
                            "children": [
                              {
                                "bgpPeerAf": {
                                  "attributes": {
                                    "capAddlPaths": "",
                                    "inheritContPeerPolicyCtrl": "",
                                    "type": "ipv6-lucast"
                                  },
                                  "children": [
                                    {
                                      "bgpPolicyInheritRule": {
                                        "attributes": {
                                          "name": "Pol1",
                                          "seq": "123"
                                        }
                                      }
                                    }
                                  ]
                                }
                              }
                            ]
                          }
                        },
                        {
                          "bgpPolicyCont": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "name": "Pol1"
                            }
                          }
                        }
                      ]
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <capAddlPaths></capAddlPaths>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <pol-items>
                    <PolicyInheritRule-list>
                      <name>Pol1</name>
                      <seq>123</seq>
                    </PolicyInheritRule-list>
                  </pol-items>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
          <policycont-items>
            <PolicyCont-list>
              <name>Pol1</name>
              <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
            </PolicyCont-list>
          </policycont-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 template peer-policy Pol1
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
   inherit peer-policy Pol1 123
    default capability additional-paths receive

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPolicyInheritRule Properties

The following table contains information about the bgpPolicyInheritRule properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPolicyCont Properties

The following table contains information about the bgpPolicyCont properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring a Third-Party Nexthop (If Possible)

Configuring a Third-Party Nexthop (If Possible)

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "123"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeer": {
                      "attributes": {
                        "addr": "1.2.3.4",
                        "inheritContPeerCtrl": ""
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "nhThirdparty": "enabled",
                              "type": "ipv6-lucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <nhThirdparty>enabled</nhThirdparty>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
  next-hop-third-party

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting a Third-Party Nexthop

Deleting a Third-Party Nexthop

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "123"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeer": {
                      "attributes": {
                        "addr": "1.2.3.4",
                        "inheritContPeerCtrl": ""
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "nhThirdparty": "disabled",
                              "type": "ipv6-lucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <nhThirdparty>disabled</nhThirdparty>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
  no next-hop-third-party

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring a Third-Party Nexthop (Values inherited from a Peer Template)

Configuring a Third-Party Nexthop (Values inherited from a Peer Template) 

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "topSystem": {
    "children": [
      {
        "bgpEntity": {
          "children": [
            {
              "bgpInst": {
                "attributes": {
                  "asn": "123"
                },
                "children": [
                  {
                    "bgpDom": {
                      "attributes": {
                        "name": "default"
                      },
                      "children": [
                        {
                          "bgpPeer": {
                            "attributes": {
                              "addr": "1.2.3.4",
                              "inheritContPeerCtrl": "",
                              "peerImp": "peer"
                            },
                            "children": [
                              {
                                "bgpPeerAf": {
                                  "attributes": {
                                    "inheritContPeerPolicyCtrl": "",
                                    "nhThirdparty": "enabled",
                                    "type": "ipv6-lucast"
                                  },
                                  "children": [
                                    {
                                      "bgpPolicyInheritRule": {
                                        "attributes": {
                                          "name": "Pol1",
                                          "seq": "123"
                                        }
                                      }
                                    }
                                  ]
                                }
                              }
                            ]
                          }
                        },
                        {
                          "bgpPolicyCont": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "name": "Pol1"
                            }
                          }
                        }
                      ]
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <peerImp>peer</peerImp>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <nhThirdparty>enabled</nhThirdparty>
                  <pol-items>
                    <PolicyInheritRule-list>
                      <name>Pol1</name>
                      <seq>123</seq>
                    </PolicyInheritRule-list>
                  </pol-items>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
          <policycont-items>
            <PolicyCont-list>
              <name>Pol1</name>
              <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
            </PolicyCont-list>
          </policycont-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 template peer-policy Pol1
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
   inherit peer-policy Pol1 123
    default next-hop-third-party

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPolicyInheritRule Properties

The following table contains information about the bgpPolicyInheritRule properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPolicyCont Properties

The following table contains information about the bgpPolicyCont properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring a Route-Map to Selectively Unsuppress Suppressed Routes

Configuring a Route-Map to Selectively Unsuppress Suppressed Routes 

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "123"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeer": {
                      "attributes": {
                        "addr": "1.2.3.4",
                        "inheritContPeerCtrl": ""
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "ipv6-lucast",
                              "unSupprMap": "Map1"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <unSupprMap>Map1</unSupprMap>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
  unsuppress-map Map1

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting a Configuration that Selectively Unsuppress Suppressed Routes

Deleting a Configuration that Selectively Unsuppress Suppressed Routes 

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "123"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeer": {
                      "attributes": {
                        "addr": "1.2.3.4",
                        "inheritContPeerCtrl": ""
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "ipv6-lucast",
                              "unSupprMap": ""
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <unSupprMap></unSupprMap>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
  no unsuppress-map Map1

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring a Route-Map to Selectively Unsuppress Suppressed Routes (Values inherited from a Peer Template)

Configuring a Route-Map to Selectively Unsuppress Suppressed Routes (Values inherited from a Peer Template)

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "topSystem": {
    "children": [
      {
        "bgpEntity": {
          "children": [
            {
              "bgpInst": {
                "attributes": {
                  "asn": "123"
                },
                "children": [
                  {
                    "bgpDom": {
                      "attributes": {
                        "name": "default"
                      },
                      "children": [
                        {
                          "bgpPeer": {
                            "attributes": {
                              "addr": "1.2.3.4",
                              "inheritContPeerCtrl": ""
                            },
                            "children": [
                              {
                                "bgpPeerAf": {
                                  "attributes": {
                                    "inheritContPeerPolicyCtrl": "",
                                    "type": "ipv6-lucast",
                                    "unSupprMap": ""
                                  },
                                  "children": [
                                    {
                                      "bgpPolicyInheritRule": {
                                        "attributes": {
                                          "name": "Pol1",
                                          "seq": "123"
                                        }
                                      }
                                    }
                                  ]
                                }
                              }
                            ]
                          }
                        },
                        {
                          "bgpPolicyCont": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "name": "Pol1"
                            }
                          }
                        }
                      ]
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <unSupprMap></unSupprMap>
                  <pol-items>
                    <PolicyInheritRule-list>
                      <name>Pol1</name>
                      <seq>123</seq>
                    </PolicyInheritRule-list>
                  </pol-items>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
          <policycont-items>
            <PolicyCont-list>
              <name>Pol1</name>
              <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
            </PolicyCont-list>
          </policycont-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 template peer-policy Pol1  neighbor 1.2.3.4   address-family ipv6 labeled-unicast    inherit peer-policy Pol1 123     default unsuppress-map Map1 `

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPolicyInheritRule Properties

The following table contains information about the bgpPolicyInheritRule properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPolicyCont Properties

The following table contains information about the bgpPolicyCont properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring a Conditioned Route-Map to Advertise Only When Prefix in Condition Exists

Configuring a Conditioned Route-Map to Advertise Only When Prefix in Condition Exists

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "123"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeer": {
                      "attributes": {
                        "addr": "1.2.3.4",
                        "inheritContPeerCtrl": ""
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "ipv6-lucast"
                            },
                            "children": [
                              {
                                "bgpAdvtMap": {
                                  "attributes": {
                                    "condMap": "map1",
                                    "condition": "exist",
                                    "rtMap": "map1"
}}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <advtmap-items>
                    <condMap>map1</condMap>
                    <condition>exist</condition>
                    <rtMap>map1</rtMap>
                  </advtmap-items>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
  advertise-map map1 exist-map map1

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpAdvtMap Properties

The following table contains information about the bgpAdvtMap properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting a Conditioned Route-Map to Advertise Only When Prefix in Condition Exists

Deleting a Conditioned Route-Map to Advertise Only When Prefix in Condition Exists

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "123"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeer": {
                      "attributes": {
                        "addr": "1.2.3.4",
                        "inheritContPeerCtrl": ""
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "ipv6-lucast"
                            },
                            "children": [
                              {
                                "bgpAdvtMap": {
                                  "attributes": {
                                    "status": "deleted"
}}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <advtmap-items xc:operation="delete">
                  </advtmap-items>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
  no advertise-map map1 exist-map map1

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpAdvtMap Properties

The following table contains information about the bgpAdvtMap properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring a Conditioned Route-Map to Advertise Only When Prefix in Condition Does Not Exist

Configuring a Conditioned Route-Map to Advertise Only When Prefix in Condition Does Not Exist

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "123"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeer": {
                      "attributes": {
                        "addr": "1.2.3.4",
                        "inheritContPeerCtrl": ""
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "ipv6-lucast"
                            },
                            "children": [
                              {
                                "bgpAdvtMap": {
                                  "attributes": {
                                    "condMap": "rtmap1",
                                    "condition": "non-exist",
                                    "rtMap": "map1"
}}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <advtmap-items>
                    <condMap>rtmap1</condMap>
                    <condition>non-exist</condition>
                    <rtMap>map1</rtMap>
                  </advtmap-items>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
  advertise-map map1 non-exist-map rtmap1

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpAdvtMap Properties

The following table contains information about the bgpAdvtMap properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting a Conditioned Route-Map to Advertise Only When Prefix in Condition Does Not Exist

Deleting a Conditioned Route-Map to Advertise Only When Prefix in Condition Does Not Exist

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "123"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeer": {
                      "attributes": {
                        "addr": "1.2.3.4",
                        "inheritContPeerCtrl": ""
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "ipv6-lucast"
                            },
                            "children": [
                              {
                                "bgpAdvtMap": {
                                  "attributes": {
                                    "status": "deleted"
}}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <advtmap-items xc:operation="delete">
                  </advtmap-items>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
  no advertise-map map1 non-exist-map rtmap1

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpAdvtMap Properties

The following table contains information about the bgpAdvtMap properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring a Route Map for Conditional Advertisement (Values inherited From a Peer Template)

Configuring a Route Map for Conditional Advertisement (Values inherited From a Peer Template)

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "topSystem": {
    "children": [
      {
        "bgpEntity": {
          "children": [
            {
              "bgpInst": {
                "attributes": {
                  "asn": "123"
                },
                "children": [
                  {
                    "bgpDom": {
                      "attributes": {
                        "name": "default"
                      },
                      "children": [
                        {
                          "bgpPeer": {
                            "attributes": {
                              "addr": "1.2.3.4",
                              "inheritContPeerCtrl": ""
                            },
                            "children": [
                              {
                                "bgpPeerAf": {
                                  "attributes": {
                                    "inheritContPeerPolicyCtrl": "",
                                    "type": "ipv6-lucast"
                                  },
                                  "children": [
                                    {
                                      "bgpAdvtMap": {
                                        "attributes": {
                                          "status": "deleted"
                                        }
                                      }
                                    },
                                    {
                                      "bgpPolicyInheritRule": {
                                        "attributes": {
                                          "name": "Pol1",
                                          "seq": "123"
                                        }
                                      }
                                    }
                                  ]
                                }
                              }
                            ]
                          }
                        },
                        {
                          "bgpPolicyCont": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "name": "Pol1"
                            }
                          }
                        }
                      ]
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}                            

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <advtmap-items xc:operation="delete">
                  </advtmap-items>
                  <pol-items>
                    <PolicyInheritRule-list>
                      <name>Pol1</name>
                      <seq>123</seq>
                    </PolicyInheritRule-list>
                  </pol-items>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
          <policycont-items>
            <PolicyCont-list>
              <name>Pol1</name>
              <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
            </PolicyCont-list>
          </policycont-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 template peer-policy Pol1
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
   inherit peer-policy Pol1 123
    default advertise-map

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpAdvtMap Properties

The following table contains information about the bgpAdvtMap properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPolicyInheritRule Properties

The following table contains information about the bgpPolicyInheritRule properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPolicyCont Properties

The following table contains information about the bgpPolicyCont properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring a Route Map to Specify Criteria for Originating the Default

Configuring a Route Map to Specify Criteria for Originating the Default

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "123"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeer": {
                      "attributes": {
                        "addr": "1.2.3.4",
                        "inheritContPeerCtrl": ""
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "defOrg": "enabled",
                              "defOrgRtMap": "rtmap1",
                              "inheritContPeerPolicyCtrl": "",
                              "type": "ipv6-lucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <defOrg>enabled</defOrg>
                  <defOrgRtMap>rtmap1</defOrgRtMap>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
  default-originate route-map rtmap1

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting a Configured Route Map to Specify Criteria for Originating the Default

Deleting a Configured Route Map to Specify Criteria for Originating the Default

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "123"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeer": {
                      "attributes": {
                        "addr": "1.2.3.4",
                        "inheritContPeerCtrl": ""
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "defOrg": "disabled",
                              "defOrgRtMap": "rtmap1",
                              "inheritContPeerPolicyCtrl": "",
                              "type": "ipv6-lucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <defOrg>disabled</defOrg>
                  <defOrgRtMap>rtmap1</defOrgRtMap>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
  no default-originate route-map rtmap1

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring a Route Map to Specify Criteria for Originating the Default (Values inherited From a Peer Template)

Configuring a Route Map to Specify Criteria for Originating the Default (Values inherited From a Peer Template)

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "topSystem": {
    "children": [
      {
        "bgpEntity": {
          "children": [
            {
              "bgpInst": {
                "attributes": {
                  "asn": "123"
                },
                "children": [
                  {
                    "bgpDom": {
                      "attributes": {
                        "name": "default"
                      },
                      "children": [
                        {
                          "bgpPeer": {
                            "attributes": {
                              "addr": "1.2.3.4",
                              "inheritContPeerCtrl": ""
                            },
                            "children": [
                              {
                                "bgpPeerAf": {
                                  "attributes": {
                                    "defOrg": "disabled",
                                    "defOrgRtMap": "",
                                    "inheritContPeerPolicyCtrl": "",
                                    "type": "ipv6-lucast"
                                  },
                                  "children": [
                                    {
                                      "bgpPolicyInheritRule": {
                                        "attributes": {
                                          "name": "Pol1",
                                          "seq": "123"
                                        }
                                      }
                                    }
                                  ]
                                }
                              }
                            ]
                          }
                        },
                        {
                          "bgpPolicyCont": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "name": "Pol1"
                            }
                          }
                        }
                      ]
                    }
                  }
                ]
              }
            }
          ]
        }
      }
    ]
  }
}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>123</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peer-items>
            <Peer-list>
              <addr>1.2.3.4</addr>
              <inheritContPeerCtrl></inheritContPeerCtrl>
              <af-items>
                <PeerAf-list>
                  <type>ipv6-lucast</type>
                  <defOrg>disabled</defOrg>
                  <defOrgRtMap></defOrgRtMap>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <pol-items>
                    <PolicyInheritRule-list>
                      <name>Pol1</name>
                      <seq>123</seq>
                    </PolicyInheritRule-list>
                  </pol-items>
                </PeerAf-list>
              </af-items>
            </Peer-list>
          </peer-items>
          <policycont-items>
            <PolicyCont-list>
              <name>Pol1</name>
              <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
            </PolicyCont-list>
          </policycont-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 123
 template peer-policy Pol1
 neighbor 1.2.3.4
  address-family ipv6 labeled-unicast
   inherit peer-policy Pol1 123
    default default-originate route-map rtmap1

Note: The property information for this example was added in Release 9.3(3).

Verifying a DME Configuration
The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeer Properties

The following table contains information about the bgpPeer properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPolicyInheritRule Properties

The following table contains information about the bgpPolicyInheritRule properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPolicyCont Properties

The following table contains information about the bgpPolicyCont properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html