Configuring a VPNv4 Unicast Subaddress Family Under a BGP Neighbor (Ethernet Interface)

Configuring Peer Policy Inheritance

Configuring Peer Policy Inheritance 

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "type": "vpnv4-ucast"
                            },
                            "children": [
                              {
                                "bgpPolicyInheritRule": {
                                  "attributes": {
                                    "name": "SampleString_123",
                                    "seq": "8688"
}}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <pol-items>
                    <PolicyInheritRule-list>
                      <name>SampleString_123</name>
                      <seq>8688</seq>
                    </PolicyInheritRule-list>
                  </pol-items>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    inherit peer-policy SampleString_123 8688

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPolicyInheritRule Properties

The following table contains information about the bgpPolicyInheritRule properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Peer Policy Inheritance

Deleting Peer Policy Inheritance 

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "type": "vpnv4-ucast"
                            },
                            "children": [
                              {
                                "bgpPolicyInheritRule": {
                                  "attributes": {
                                    "name": "SampleString_123",
                                    "status": "deleted"
}}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <pol-items>
                    <PolicyInheritRule-list nc:operation="delete">
                      <name>SampleString_123</name>
                    </PolicyInheritRule-list>
                  </pol-items>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    no inherit peer-policy SampleString_123 8688

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPolicyInheritRule Properties

The following table contains information about the bgpPolicyInheritRule properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring As Path Acceptance with My AS Present In It

Configuring As Path Acceptance with My AS Present In It 

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "allowedSelfAsCnt": "7",
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <allowedSelfAsCnt>7</allowedSelfAsCnt>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    allowas-in 7

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting As Path Acceptance with My AS Present In It

Deleting As Path Acceptance with My AS Present In It 

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "allowedSelfAsCnt": "0",
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <allowedSelfAsCnt>0</allowedSelfAsCnt>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    no allowas-in 7

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring to Send Standard and Extended Community Attributes

Configuring to Send Standard and Extended Community Attributes

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "sendComExt": "enabled",
                              "sendComStd": "enabled",
                              "type": "vpnv4-ucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <sendComExt>enabled</sendComExt>
                  <sendComStd>enabled</sendComStd>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    send-community both

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting to Send Standard and Extended Community Attributes

Deleting to Send Standard and Extended Community Attributes

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "sendComExt": "disabled",
                              "sendComStd": "disabled",
                              "type": "vpnv4-ucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <sendComExt>disabled</sendComExt>
                  <sendComStd>disabled</sendComStd>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    no send-community both

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring to Send Standard Community Attributes

Configuring to Send Standard Community Attributes

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "sendComStd": "enabled",
                              "type": "vpnv4-ucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <sendComStd>enabled</sendComStd>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    send-community standard

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting to Send Standard Community Attributes

Deleting to Send Standard Community Attributes

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "sendComStd": "disabled",
                              "type": "vpnv4-ucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <sendComStd>disabled</sendComStd>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    no send-community standard

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Extended Community Attribute

Configuring the Extended Community Attribute

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "sendComExt": "enabled",
                              "type": "vpnv4-ucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <sendComExt>enabled</sendComExt>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    send-community extended

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting the Extended Community Attribute

Deleting the Extended Community Attribute

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "sendComExt": "disabled",
                              "type": "vpnv4-ucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <sendComExt>disabled</sendComExt>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    no send-community extended

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring a Neighbor as Route-Reflector Client

Configuring a Neighbor as Route-Reflector Client

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "ctrl": "rr-client",
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <ctrl>rr-client</ctrl>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    route-reflector-client

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting a Neighbor as Route-Reflector Client

Deleting a Neighbor as Route-Reflector Client

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "ctrl": "",
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <ctrl></ctrl>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    no route-reflector-client

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Default Weight for Routes from a Neighbor

Configuring the Default Weight for Routes from a Neighbor 

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast",
                              "wght": "155"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <wght>155</wght>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    weight 155

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting the Default Weight for Routes from a Neighbor

Deleting the Default Weight for Routes from a Neighbor 

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast",
                              "wght": ""
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <wght></wght>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    no weight 155

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Policy Application to Incoming Routes

Configuring Policy Application to Incoming Routes

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
                            },
                            "children": [
                              {
                                "bgpPfxCtrlP": {
                                  "attributes": {
                                    "direction": "in",
                                    "list": "SampleString_123"
}}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <pfxctrl-items>
                    <PfxCtrlP-list>
                      <direction>in</direction>
                      <list>SampleString_123</list>
                    </PfxCtrlP-list>
                  </pfxctrl-items>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    prefix-list SampleString_123 in

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPfxCtrlP Properties

The following table contains information about the bgpPfxCtrlP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Policy Application to Incoming Routes

Deleting Policy Application to Incoming Routes

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
                            },
                            "children": [
                              {
                                "bgpPfxCtrlP": {
                                  "attributes": {
                                    "direction": "in",
                                    "status": "deleted"
}}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <pfxctrl-items>
                    <PfxCtrlP-list nc:operation="delete">
                      <direction>in</direction>
                    </PfxCtrlP-list>
                  </pfxctrl-items>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    no prefix-list SampleString_123 in

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPfxCtrlP Properties

The following table contains information about the bgpPfxCtrlP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Policy Application (Prefix List)

Configuring Policy Application (Prefix List)

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
                            },
                            "children": [
                              {
                                "bgpPfxCtrlP": {
                                  "attributes": {
                                    "direction": "out",
                                    "list": "SampleString_123"
}}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <pfxctrl-items>
                    <PfxCtrlP-list>
                      <direction>out</direction>
                      <list>SampleString_123</list>
                    </PfxCtrlP-list>
                  </pfxctrl-items>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    prefix-list SampleString_123 out

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPfxCtrlP Properties

The following table contains information about the bgpPfxCtrlP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Policy Application (Prefix List)

Deleting Policy Application (Prefix List)

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
                            },
                            "children": [
                              {
                                "bgpPfxCtrlP": {
                                  "attributes": {
                                    "direction": "out",
                                    "status": "deleted"
}}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <pfxctrl-items>
                    <PfxCtrlP-list nc:operation="delete">
                      <direction>out</direction>
                    </PfxCtrlP-list>
                  </pfxctrl-items>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    no prefix-list SampleString_123 out

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPfxCtrlP Properties

The following table contains information about the bgpPfxCtrlP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring a Policy Application to Incoming Routes

Configuring a Policy Application to Incoming Routes

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
                            },
                            "children": [
                              {
                                "bgpFltrCtrlP": {
                                  "attributes": {
                                    "direction": "in",
                                    "list": "SampleString_123"
}}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <fltrctrl-items>
                    <FltrCtrlP-list>
                      <direction>in</direction>
                      <list>SampleString_123</list>
                    </FltrCtrlP-list>
                  </fltrctrl-items>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    filter-list SampleString_123 in

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpFltrCtrlP Properties

The following table contains information about the bgpFltrCtrlP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting a Policy Application to Incoming Routes

Deleting a Policy Application to Incoming Routes

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
                            },
                            "children": [
                              {
                                "bgpFltrCtrlP": {
                                  "attributes": {
                                    "direction": "in",
                                    "status": "deleted"
}}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <fltrctrl-items>
                    <FltrCtrlP-list nc:operation="delete">
                      <direction>in</direction>
                    </FltrCtrlP-list>
                  </fltrctrl-items>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    no filter-list SampleString_123 in

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpFltrCtrlP Properties

The following table contains information about the bgpFltrCtrlP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Policy Application (Filter List)

Configuring Policy Application (Filter List)

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
                            },
                            "children": [
                              {
                                "bgpFltrCtrlP": {
                                  "attributes": {
                                    "direction": "out",
                                    "list": "SampleString_123"
}}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <fltrctrl-items>
                    <FltrCtrlP-list>
                      <direction>out</direction>
                      <list>SampleString_123</list>
                    </FltrCtrlP-list>
                  </fltrctrl-items>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    filter-list SampleString_123 out

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpFltrCtrlP Properties

The following table contains information about the bgpFltrCtrlP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Policy Application (Filter List)

Deleting Policy Application (Filter List)

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
                            },
                            "children": [
                              {
                                "bgpFltrCtrlP": {
                                  "attributes": {
                                    "direction": "out",
                                    "status": "deleted"
}}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <fltrctrl-items>
                    <FltrCtrlP-list nc:operation="delete">
                      <direction>out</direction>
                    </FltrCtrlP-list>
                  </fltrctrl-items>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    no filter-list SampleString_123 out

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpFltrCtrlP Properties

The following table contains information about the bgpFltrCtrlP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring BGP Connection Restart After a Limit is Exceeded

Configuring BGP Connection Restart After a Limit is Exceeded 

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
                            },
                            "children": [
                              {
                                "bgpMaxPfxP": {
                                  "attributes": {
                                    "action": "restart",
                                    "maxPfx": "1",
                                    "restartTime": "27129",
                                    "thresh": "4"
}}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <maxpfxp-items>
                    <action>restart</action>
                    <maxPfx>1</maxPfx>
                    <restartTime>27129</restartTime>
                    <thresh>4</thresh>
                  </maxpfxp-items>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    maximum-prefix 1 4 restart 27129

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpMaxPfxP Properties

The following table contains information about the bgpMaxPfxP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting BGP Connection Restart After a Limit is Exceeded

Deleting BGP Connection Restart After a Limit is Exceeded 

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
                            },
                            "children": [
                              {
                                "bgpMaxPfxP": {
                                  "attributes": {
                                    "status": "deleted"
}}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <maxpfxp-items nc:operation="delete">
                  </maxpfxp-items>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    no maximum-prefix 1 4 restart 27129

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpMaxPfxP Properties

The following table contains information about the bgpMaxPfxP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring a Warning Message When a Limit is Exceeded

Configuring a Warning Message When a Limit is Exceeded

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
                            },
                            "children": [
                              {
                                "bgpMaxPfxP": {
                                  "attributes": {
                                    "action": "log",
                                    "maxPfx": "1",
                                    "restartTime": "0",
                                    "thresh": "4"
}}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <maxpfxp-items>
                    <action>log</action>
                    <maxPfx>1</maxPfx>
                    <restartTime>0</restartTime>
                    <thresh>4</thresh>
                  </maxpfxp-items>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    maximum-prefix 1 4 warning-only

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpMaxPfxP Properties

The following table contains information about the bgpMaxPfxP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting a Warning Message When a Limit is Exceeded

Deleting a Warning Message When a Limit is Exceeded

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
                            },
                            "children": [
                              {
                                "bgpMaxPfxP": {
                                  "attributes": {
                                    "status": "deleted"
}}}]}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <maxpfxp-items nc:operation="delete">
                  </maxpfxp-items>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    no maximum-prefix 1 4 warning-only

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpMaxPfxP Properties

The following table contains information about the bgpMaxPfxP properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring the Minimum Interval Between Sending BGP Routing Updates

Configuring the Minimum Interval Between Sending BGP Routing Updates 

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "advIntvl": "219",
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <advIntvl>219</advIntvl>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    advertisement-interval 219

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting the Minimum Interval Between Sending BGP Routing Updates

Deleting the Minimum Interval Between Sending BGP Routing Updates 

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "advIntvl": "0",
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <advIntvl>0</advIntvl>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    no advertisement-interval 219

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring Our Address as Nexthop for All Routes

Configuring Our Address as Nexthop for All Routes

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "ctrl": "",
                              "inheritContPeerPolicyCtrl": "",
                              "nhSelfAll": "yes",
                              "type": "vpnv4-ucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <ctrl></ctrl>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <nhSelfAll>true</nhSelfAll>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    next-hop-self all

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting Our Address as Nexthop for All Routes

Deleting Our Address as Nexthop for All Routes

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "ctrl": "",
                              "inheritContPeerPolicyCtrl": "",
                              "nhSelfAll": "no",
                              "type": "vpnv4-ucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <ctrl></ctrl>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <nhSelfAll>false</nhSelfAll>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    no next-hop-self all

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring to Not Advertise Additional Paths (Send Capability)

Configuring to Not Advertise Additional Paths (Send Capability)

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "capAddlPaths": "send-disable",
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <capAddlPaths>send-disable</capAddlPaths>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    capability additional-paths send disable

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting to Not Advertise Additional Paths (Send Capability)

Deleting to Not Advertise Additional Paths (Send Capability)

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "capAddlPaths": "",
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <capAddlPaths></capAddlPaths>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    no capability additional-paths send disable

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring to Not Advertise Additional Paths (Receive Capability)

Configuring to Not Advertise Additional Paths (Receive Capability)

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "capAddlPaths": "recv-disable",
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <capAddlPaths>recv-disable</capAddlPaths>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    capability additional-paths receive disable

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting to Not Advertise Additional Paths (Receive Capability)

Deleting to Not Advertise Additional Paths (Receive Capability)

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "capAddlPaths": "",
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <capAddlPaths></capAddlPaths>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    no capability additional-paths receive disable

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Configuring a Route Map to Selectively Unsuppress Suppressed Routes

Configuring a Route Map to Selectively Unsuppress Suppressed Routes

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast",
                              "unSupprMap": "SampleString_123"
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <unSupprMap>SampleString_123</unSupprMap>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    unsuppress-map SampleString_123

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Deleting a Route Map to Selectively Unsuppress Suppressed Routes

Deleting a Route Map to Selectively Unsuppress Suppressed Routes

POST http://<mgmt0_IP>/api/mo/sys/bgp.json

{
  "bgpEntity": {
    "children": [
      {
        "bgpInst": {
          "attributes": {
            "asn": "100"
          },
          "children": [
            {
              "bgpDom": {
                "attributes": {
                  "name": "default"
                },
                "children": [
                  {
                    "bgpPeerIf": {
                      "attributes": {
                        "id": "eth1/2"
                      },
                      "children": [
                        {
                          "bgpPeerAf": {
                            "attributes": {
                              "inheritContPeerPolicyCtrl": "",
                              "type": "vpnv4-ucast",
                              "unSupprMap": ""
}}}]}}]}}]}}]}}

{
    imdata:[]
}

<System>
  <bgp-items>
    <inst-items>
      <asn>100</asn>
      <dom-items>
        <Dom-list>
          <name>default</name>
          <peerif-items>
            <PeerIf-list>
              <id>eth1/2</id>
              <af-items>
                <PeerAf-list>
                  <type>vpnv4-ucast</type>
                  <inheritContPeerPolicyCtrl></inheritContPeerPolicyCtrl>
                  <unSupprMap></unSupprMap>
                </PeerAf-list>
              </af-items>
            </PeerIf-list>
          </peerif-items>
        </Dom-list>
      </dom-items>
    </inst-items>
  </bgp-items>
</System>

Note: This example was added in Release 9.3(3).

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right. Click the DME tab in the top-left corner of the right pane to view the JSON payload. Click the YANG tab to view the XML payload.

router bgp 100
  neighbor ethernet 1/2
   address-family vpnv4 unicast
    no unsuppress-map SampleString_123

Verifying a DME Configuration

The following table contains the distinguished name (DN) for each managed object (MO) in the DME payload. Issue a GET request using the DN to verify the configuration was posted or to get information about the configured properties of a particular object.

bgpInst Properties

The following table contains information about the bgpInst properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpDom Properties

The following table contains information about the bgpDom properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerIf Properties

The following table contains information about the bgpPeerIf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

bgpPeerAf Properties

The following table contains information about the bgpPeerAf properties in the DME payload. For more information about the properties and MOs, see the NX-API DME Model Reference linked in the Related Documentation section below.

Related Documentation

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference:

http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

See the NX-API DME Model Reference for detailed information about classes and attributes described in the payload:

https://developer.cisco.com/site/nx-os/docs/nexus-model-reference/

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide:

https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html