Resetting UDLD

Resetting UDLD

POST http://<mgmt0_IP>/api/mo/sys/action.json

{
     "actionLSubj": {
         "attributes": {
             "dn": "sys/action/lsubj-[sys/udld/inst]"
                  }
                    "children" : [{
                        "udldInstResetLTask" : {
                            "attributes" : {
                                "adminSt" : "start",
                                "dn" : "sys/action/lsubj-[sys/udld/inst]/udldInstResetLTask",
                                "freq": "one-shot"
                                }
                             }
                       }]
             }
       }

{
  "imdata": []
}

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right.

udld reset

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference: http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

For detailed information about classes and attributes in the payload, see the NX-API DME Model Reference: https://developer.cisco.com/media/dme/index.html

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide: https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html

Ping

Ping

POST http://<mgmt0_IP>/api/mo/sys/action.json

{
      "actionLSubj": {
          "attributes": {
              "dn": "sys/action/lsubj-[sys]"
                }
                "children" : [{
                     "topSystemPingLTask" : {
                         "attributes" : {
                            "adminSt" : "start",
                            "dn" : "sys/action/lsubj-[sys]/topSystemPingLTask",
                            "dstIp" : "",
                            "vrf" : "",
                            "ctrl" : "",
                            "numPkt" : "",
                            "pktSz" : "",
                            "timeout" : "",
                            "sendIntvl" : "",
                            "srcIp" : "1.1.1.1",
                            "srcIf" : "",
                            "tos" : "",
                            "ttl" : "",
                            "freq": "one-shot"
                        }

                }
           }]
      }
}

{
  "imdata": []
}

CLI Commands

The CLI commands are equivalent to the payload examples displayed in the pane on the right.

ping ?
  <CR>
  A.B.C.D or Hostname IP address of remote system
  WORD Enter Hostname
  multicast Multicast ping

ping 1.1.1.1 ?
  <CR>
  count Number of pings to send
  df-bit Enable do not fragment bit in IP header
  interval Wait interval seconds between sending each packet
  packet-size Packet size to send
  source Source IP address to use
  source-interface Select source interface
  timeout Specify timeout interval
  vrf Display per-VRF information

For other CLI options, see the Cisco Nexus 9000 Series NX-OS Command Reference: http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-command-reference-list.html

For detailed information about classes and attributes in the payload, see the NX-API DME Model Reference: https://developer.cisco.com/media/dme/index.html

For information about using the payloads, see the Cisco Nexus 9000 Series NX-OS Programmability Guide: https://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/products-programming-reference-guides-list.html